This page centralizes documentation relating to the module loading, integration, and quality control/assurance testing of the Inner System, part of ATLAS' Inner Tracker Pixels Phase II upgrade project.
Calendar of the personnel on site
Quick access resources for module loading & integration
- Module mechanical drawings (AT2-IP-EP-0009 v4)
- Dummy Heaters information including drawings, dimensions, soldering procedures, and testing
- Quad module properties
- 3D-printed dummy ring properties
- SE4445 cartridges at SLAC: Glue in freezer log
- Access the Electronic Logbook & its documentation
- On-site access during COVID-19
p19-0 Prototypes
p19-0: Coupled ring & L0 stave
Ring loading [Tubes Up] [Tubes Down]
Stave loading [p19-0 stave anatomy]
p19-1
Parts expected to begin arriving at SLAC in July 2021
p19-2
Module loading pages
Building 33: Module loading equipment
Consumable components for mixing and dispensing SE4445
A list of consumables required for mixing SE4445, storing it in syringes, and dispensing it with the Janome robot.
The linked page includes the information required to place orders for each item.
Glue dispensing equipment
Page describing the air dispenser, PC, and Janome robot for glue dispensing. The page labels the equipment. The operations instructions are obsolete. Please follow the latest instructions here.
- In addition, we now have an edge finder we can mount on the robot.
Quad & triplet pick up plates
- CMM measurements from October 23 & 29, 2020; February 25, 2021
- Pickup Plates w- grooves.pdf
- REF-000112056 RD53a Ring_Triplet top view only.pdf
- some dimensions from PF-256-102-70.pdf
- view of PF-256-102-30 PICK UP PLATE SGL-TPL with 20mm slides.pdf
- view of PF-256-102-30 PICK UP PLATE SGL-TPL with 22mm slides.pdf
Equipment manuals
- Nordson EFD Ultimus V dispenser [PDF] [Confluence page]
- Checking the temperature of a syringe with the IR camera [Confluence]
- Janome Points software [Confluence]
- ITk pixel module QC cooling unit [Confluence]
- LBL-loaned Keyence glue mixer
Datasheets
Building 33: Operating procedures
Mixing SE4445 cartridges for storage
- This page describes how to set up and mix SE4445 into smaller syringes for later use in the B33 cleanroom complex gowning area.
Building 33 - Glue freezer monitoring setup
Page describing the setup of the LabJack 7 + thermocouples, as well as monitoring software, PC setup, network setup.
Dispensing SE4445
- Step-by-step procedure for using the Nordson dispenser and robot in B33 to deposit SE4445 in a star pattern.
- Advanced programming concepts for the Janome Points software
- We can only predict so many eventualities: This page describes how to create your own custom Janome Points program file. It breaks down some key concepts (like Janome jargon "Point Job," "PTP," and "palette") as well as how to set up the Janome Points programme.
Running the CMM
- Describes how to operate the CMM in the small clean room in B33
Rework procedure
- Using fishing line and ethanol, we can remove heaters from staves. [Confluence]
SE4445 Glue Layer Analysis
Further documentation and resources
Datasets | Tables of wet and dry dispensing datasets collected after October 2020 |
|---|---|
Related presentations | Contains copies of lab notes and documents in addition to links for relevant presentations between August 2018 and February 2020 |
Module mounting glue options |
|
Integration Pages
|
|
|
B33-CO2 Plant Approved ProcedureCO2-plant equipment information, approved procedures and hazard | B33 - Operating the QC Test BoxProcedures for operating the CO2 Plant and test box equipment | Thermal TestDescription and details on thermal test procedures. |
Discussion on Stavelet strategy [Confluence, 2019-08-21]
2019 requirements for the design and instrumentation in the SLAC test box [Confluence]
Readout and Q/C setups
 |
|
|
|
|
|
|---|---|---|---|---|---|
ITk pixel DAQ readout infrastructure and network at SLAC. This page requires ATLAS-confluence-editor permission | RCE ReadoutRCE test bench documentation for SLAC ITk local setups. More general RCE readout documentations on CERN Twiki RCEDevelopmentLab | YARR ReadoutYARR test bench documentations. | Felix readout documentation for the Felix712 | Direct FELIX readoutFELIX readout system documentations, direct FELIX setups, and test configurations. | General DAQ operation GUI interface and instructions common to all DAQ platforms |
|
|
| |
|---|---|---|---|
Module Q/C PortalModule general info. Test spec and infrastructure. Module inventory. | Cooling Unit for Module QCInformation on cooling unit for module QC | DCS control/monitoringInformation on infrastructure and instructions for LV/HV PSU control and monitoring | DCS InterlockInterlock setup for Lab and B33 integration |
This page centralizes documentation relating to the module loading, integration, and quality control/assurance testing of the Inner System, part of ATLAS' Inner Tracker Pixels Phase II upgrade project.
Calendar of the personnel on site
Quick access resources for module loading & integration
- Module mechanical drawings (AT2-IP-EP-0009 v4)
- Dummy Heaters information including drawings, dimensions, soldering procedures, and testing
- Quad module properties
- 3D-printed dummy ring properties
- Access the Electronic Logbook & its documentation
- On-site access during COVID-19
p19-0 Prototypes
p19-0: Coupled ring & L0 stave
Ring loading [Tubes Up] [Tubes Down]
Stave loading [p19-0 stave anatomy]
p19-1
Parts expected to begin arriving at SLAC in July 2021
p19-2
Module loading pages
Building 33: Module loading equipment
Consumable components for mixing and dispensing SE4445
A list of consumables required for mixing SE4445, storing it in syringes, and dispensing it with the Janome robot.
The linked page includes the information required to place orders for each item.
Glue dispensing equipment
Page describing the air dispenser, PC, and Janome robot for glue dispensing. The page labels the equipment. The operations instructions are obsolete. Please follow the latest instructions here.
- In addition, we now have an edge finder we can mount on the robot.
Quad & triplet pick up plates
- CMM measurements from October 23 & 29, 2020; February 25, 2021
- Pickup Plates w- grooves.pdf
- REF-000112056 RD53a Ring_Triplet top view only.pdf
- some dimensions from PF-256-102-70.pdf
- view of PF-256-102-30 PICK UP PLATE SGL-TPL with 20mm slides.pdf
- view of PF-256-102-30 PICK UP PLATE SGL-TPL with 22mm slides.pdf
Equipment manuals
- Nordson EFD Ultimus V dispenser [PDF] [Confluence page]
- Checking the temperature of a syringe with the IR camera [Confluence]
- Janome Points software [Confluence]
- ITk pixel module QC cooling unit [Confluence]
- LBL-loaned Keyence glue mixer
Datasheets
Building 33: Operating procedures
Mixing SE4445 cartridges for storage
- This page describes how to set up and mix SE4445 into smaller syringes for later use in the B33 cleanroom complex gowning area.
Building 33 - Glue freezer monitoring setup
Page describing the setup of the LabJack 7 + thermocouples, as well as monitoring software, PC setup, network setup.
Dispensing SE4445
- Step-by-step procedure for using the Nordson dispenser and robot in B33 to deposit SE4445 in a star pattern.
- Advanced programming concepts for the Janome Points software
- We can only predict so many eventualities: This page describes how to create your own custom Janome Points program file. It breaks down some key concepts (like Janome jargon "Point Job," "PTP," and "palette") as well as how to set up the Janome Points programme.
Running the CMM
- Describes how to operate the CMM in the small clean room in B33
Rework procedure
- Using fishing line and ethanol, we can remove heaters from staves. [Confluence]
SE4445 Glue Layer Analysis
Further documentation and resources
Datasets | Tables of wet and dry dispensing datasets collected after October 2020 |
|---|---|
Related presentations | Contains copies of lab notes and documents in addition to links for relevant presentations between August 2018 and February 2020 |
Module mounting glue options |
|
Integration Pages
|
|
|
B33-CO2 Plant Approved ProcedureCO2-plant equipment information, approved procedures and hazard | B33 - Operating the QC Test BoxProcedures for operating the CO2 Plant and test box equipment | Thermal TestDescription and details on thermal test procedures. |
Discussion on Stavelet strategy [Confluence, 2019-08-21]
2019 requirements for the design and instrumentation in the SLAC test box [Confluence]
Readout and Q/C setups
|
|
|
|
|
|---|---|---|---|---|
ITk pixel DAQ readout infrastructure and network at SLAC. This page requires ATLAS-confluence-editor permission | RCE ReadoutRCE test bench documentation for SLAC ITk local setups. More general RCE readout documentations on CERN Twiki RCEDevelopmentLab | YARR ReadoutYARR test bench documentations. | FELIX readoutFELIX readout system documentations, direct FELIX setups, and test configurations. | General DAQ operation GUI interface and instructions common to all DAQ platforms |
|
|
| |
|---|---|---|---|
Module Q/C PortalModule general info. Test spec and infrastructure. Module inventory. | Cooling Unit for Module QCInformation on cooling unit for module QC | DCS control/monitoringInformation on infrastructure and instructions for LV/HV PSU control and monitoring | DCS InterlockInterlock setup for Lab and B33 integration |