Excerpt |
---|
Half-module # | Contains hybrid | Contains sensor | Hybrid glued | Sensor glued | Sent to UCSC | HV wirebonded | Signals wirebonded | QA tested | Results | Sent to SLAC | Mounted to cooling block | Part of module | Notes |
---|
Half-module 0 - THE GIMP | Hybrid 0 | Sensor 1803 | to fixture | lousy | with a prayer | mashed bonds | painfully | ? test 1 | 4 chips bonded, and 4 are alive. 3 of them are both bonded and alive. | ? | never | Module ? | | Half-module 1 | Hybrid 1 | Sensor 568 | 2/23/12(TKN) | 2/23/12(TKN) | 2/23/12(AG) | 2/27/12(FM) | 2/29/12(FM) | 2/28/12 test 1 2/29/12 test 2 3/4/12 test 3 | OK: test 2 Baseline tests by PH show high noise in channel 81 - partial pinhole? | 3/12/12(TKN) | ? | Module |
|
...
...
...
High noise? (To retest) Chan 625 unbonded, 627 |
|
...
dead. High noise is only on run 2 - |
|
...
believed due to noisy electrical contact between CF and baseplate. | | |
|
...
| Cont'ed on next line | Cont'ed No 3 | | | | | | | Chan |
|
...
...
...
...
...
...
...
...
: test 5 (but cal7_8x3_125ns is bad for this run) | 3/23/12(PH) | ? | Module |
|
...
B5 | Needs ITT connector | Half-module 6 | Hybrid 7t | Sensor 138 | 3/18/12(TKN) | 3/18/12(TKN) | 3/19/12 (TKN/VF) | 3/21/12(FM) noticed scratch on Bias/Guard rings. But IV is OK up to 300V. | 3/22/12(FM) | 3/22/12 test 1 3/22/12 test 2 | OK except channels 0 (no response), 134, 639 (noisy response). Channel 0 is bad b/c of the scratch that connects it with bias ring. | 3/23/12(PH) | ? | Module |
|
...
...
? test 1
...
?
...
...
...
...
?
...
? test 1
...
?
...
...
...
...
?
...
?
...
? test 1
...
?
3/23/12(FM) | 3/23/12(FM) | 3/26/12 test 1 | Channel 466 has no response (as on hybrid), else OK. | 3/27/12(OM) |
|
...
...
...
...
?
...
?
...
? test 1
...
?
3/23/12(FM) | 3/23/12(FM) | 3/26/12 test 1 3/27/12 test 2 3/27/12 test 3 3/27/12 test 4 3/28/12 test 5 3/28/12 test 6 | Channels 81 and 83 shorted? Else OK. All channels are OK from test 3 on. | 3/27/12(PH) |
|
...
...
...
...
?
...
?
...
? test 1
...
?
3/23/12(FM) | 3/23/12(FM) | 3/26/12 test 1 3/27/12 test 2 3/27/12 test 3 3/28/12 test 4 3/28/12 test 5 3/28/12 test 6 3/28/12 test 7 3/28/12 test 8 3/28/12 test 9 3/28/12 test 10 3/28/12 test 11 | Shorts between channels 262 and 264 as well as between channels 403 and 405; channel 183 dead and high noise on channel 184; else OK. 262-264 and 403-405 appear to have been fixed as of test 3: test 10 | 3/27/12(PH) |
|
...
...
...
?
...
?
...
? test 1
...
?
...
...
...
...
?
...
?
...
? test 1
...
?
...
...
...
...
...
?
...
?
...
? test 1
...
?
...
...
Hybrid 18t
...
Sensor 157
...
3/23/12(TKN)
...
?
...
?
...
?
...
?
...
? test 1
...
?
...
...
...
...
...
...
?
...
...
To add a half-module, copy the line below into the table and fill in the ?s.
No Format |
---|
|[Half-module ?] | [Hybrid ?] | [Sensor ?] | ? | ? | ? | ? | ? | ? [test 1|Half-module ?, test 1]| ? | ? | ? |[Module ?]| PROCESSING |
|
Add Page |
---|
template | Half-module template |
---|
parent | @self |
---|
prefix | Half-module |
---|
linkText | Add half-module page |
---|
|
Half-module Channel Mapping
Following the DAQ channel ordering and the sensor strip channel numbering the conversion between the two is summarized below.
Link to DAQ page.
hybrid-chip-numbering.png Image Removed