You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 73 Next »

Names are broken down into the standard parts, DeviceType : Area : Position :  <Instance>:Attribute

Device Type

NameDescription
ACCLUsed for everything in the RF system that is part of the general physics and operations interface at the cavity level
GUNUsed for everything in the gun


Area, Subset of Accelerator With RF Devices

See https://slacspace.slac.stanford.edu/sites/lcls/lcls-2/wd/dsg/Forms/AllItems.aspx, Naming Convention section 6.1.2.2

AreaPhysical Location
GUNBLCLS-II Gun
L0B

LCLS-II L0 Accelerator Region

L1B

LCLS-II L1 Accelerator Region

BC1B

LCLS-II Bunch Compressor 1

L2B

LCLS-II L2 Accelerator Region

BC2B

LCLS-II Bunch Compressor 2

L3BLCLS-II L3 Accelerator Region
SYS2Full LCLS-II Accelerator scope, e.g. global phase offset


Position

See https://slacspace.slac.stanford.edu/sites/lcls/lcls-2/wd/dsg/Forms/AllItems.aspx, Naming Convention section 6.1.2.3.2

The position of the gun is 100. The position of the buncher is 455.

The position of a superconducting cavity is 4 numbers where the first two indicate the cryomodule and the second two the cavity. For example, 0430 is cryomodule 4, cavity 3.

Each cryomodule has 8 cavities. Cavities 1-4 are instrumented in LLRF Rack A. Cavities 5-8 are instrumented in LLRF Rack B.


Cryo Module #

Description

01-35

CM01-CM35, 1.3GHz cavity

H1

3.9GHz Cryomodule 1, located in L1B and follows CM03

H2

3.9GHz Cryomodule 2, located in L1B and follows  H1


Numbering of cavities within a cryomodule:


Instance

The instance field is optional. When used, it specifies a sub-category of signals associated with the device.

Attribute

Attributes that comprise the physics interface. Scalar unless otherwise specified

R/WNameDescription

SRF Example

(CM 2 Cavity 1)

Gun/Buncher Example
R/WRFMODECTRLRF mode control (SEL, SELA, SELAP, SEL Raw, Pulse, Chirp) ACCL:L1B:0210:RFMODECTRL N/A
RRFMODEReadback of current RF mode (SEL, SELA, SELAP, SEL Raw, Pulse, Chirp, Tone) ACCL:L1B:0210:RFMODE
R/WRFCTRLCavity on/off control. Off = LLRF drive set to 0. (SSA control will be different.) ACCL:L1B:0210:RFCTRL
RRFSTATEReadback of cavity RF on/off state ACCL:L1B:0210:RFSTATE

 N/A

RRFREADYFORBEAM

Indicates cavity is in an okay state for beam operation. Possible states:

Ready (numerical 1) = cavity RF is On and mode is SELAP

Not ready (numerical 0) = Ready criteria not met

ACCL:L1B:0210:RFREADYFORBEAM
R/WADES

Operation amplitude setpoint (MV)

(For SRF, this setting is used in SEL, SELA, SELAP modes.)

 ACCL:L1B:0210:ADES
RGDESGradient setpoint (MV/m) - readback only ACCL:L1B:0210:GDES N/A
RSEL_ASETSRF amplitude setpoint in SEL Raw, Pulse, Chirp modes. Is in units of % of full drive scale. ACCL:L1B:0210:SEL_ASET N/A
RAACTMEANMeasured amplitude from cavity probe (MV), averaged over LLRF waveform. Identical to CAV:AMEAN. Typically averaged over ~350 ms, but this can vary depending on waveform settings.
 ACCL:L1B:0210:AACTMEAN
RGACTMEANMeasured gradient from cavity probe (MV/m), averaged over LLRF waveform. Typically averaged over ~350 ms, but this can vary depending on waveform settings.
 ACCL:L1B:0210:GACTMEAN
RADES_MAX

Maximum allowable amplitude (MV). Minimum of SRF, RF, and Ops limits (below).

 ACCL:L1B:0210:ADES_MAX
R/WADES_MAX_SRF

SRF maximum allowable amplitude, set by SRF experts (MV)

 ACCL:L1B:0210:ADES_MAX_SRF
R/WADES_MAX_RFRF maximum allowable amplitude, set by RF experts  (MV) ACCL:L1B:0210:ADES_MAX_RF
R/WADES_MAX_OPSOps maximum allowable amplitude, set by Operations experts (MV) ACCL:L1B:0210:ADES_MAX_OPS
R/WPDESOperation phase setpoint (degrees, where 0 is on-crest by convention). Range -180 to 180.
 ACCL:L1B:0210:PDES
RPACTMEANMeasured phase from cavity probe (degrees), averaged over LLRF waveform. Identical to CAV:PMEAN. Typically averaged over ~350 ms, but this can vary depending on waveform settings. ACCL:L1B:0210:PACTMEAN
R/WPREF

Phase offset (degrees) used by LLRF to convert measured phase to one relative to on-crest operation, adjusted by (gold) beam phasing.  How to use:

  1. Find maximum energy by adjusting PDES
  2. Set PREF to (PREF - PDES) (no cavity phase change will occur)
  3. Set PDES to 0 (no cavity phase change will occur)

PREF is subtracted from PDES before writing phase to hardware. PREF is added to the raw phase readback from hardware.

 ACCL:L1B:0210:PREF
R/WPTOF

Phase offset (degrees) used to adjust for changes in beam time-of-arrival, in particular for changes in bunch compressor path length. Unlike PREF, changing PTOF will immediately change the cavity phase. 

PTOF is subtracted from PDES before writing phase to hardware. PTOF is added to the raw phase readback from hardware.

ACCL:L1B:0210:PTOF
R/WSEL_POFFSEL phase offset setpoint ACCL:L1B:0210:SEL_POFF N/A
RSEL_POFF_RBVSEL phase offset readback ACCL:L1B:0210:SEL_POFF_RBV N/A
RDFACTMeasured detune frequency (Hz)N/A
RDFMeasured detune frequency (Hz) using state space equation, cavity and forward signals - used to drive piezos ACCL:L1B:0210:DF N/A
RDFVALIDMeasured detune frequency (Hz) using state space equation, cavity and forward signals is valid. If it is not valid, its value cannot be used and the resonance system will not automatically change the piezo setting. In order for it to be valid, there must be sufficient cavity signal and it must be within +/- a couple hundred Hz. ACCL:L1B:0210:DFVALID N/A
RDF_FCMeasured detune frequency (Hz) using frequency counter method -  not used in resonance control, larger operating range than DF ACCL:L1B:0210:DF_FC N/A
RCHIRP:DFMeasured detune frequency (Hz) using chirp method -  only active in Chirp and Pulsed modes, primarily for use when cavity is many kHz out of tune, operating range of tens of kHz or more ACCL:L1B:0210:CHIRP:DF N/A
R/WALEMLEM computed integrated RF amplitude (MV) per cavity and per cryomodule ACCL:L1B:0210:ALEM
R/WPLEMLEM computed phase (deg) ACCL:L1B:0210:PLEM
R/WEGLEMLEM computed energy gain (MeV) ACCL:L1B:0210:EGLEM
R/WCHLEMLEM computed chirp (MeV) ACCL:L1B:0210:CHLEM
R/WCAV:FUDGE

Beam-based scale factor applied to cavity probe amplitude readback. Nominal value of 1.

CAV:SCALE = cavity_preliminary_scaling * CAV:FUDGE

CAV:SCALE is applied at the waveform level and so FUDGE is included in scalars like AACT, CAV:AMEAN, CAV:AMIN, CAV:AMAX, etc. and waveforms like CAV:IWF, CAV:QWF, CAV:AWF, etc.

 ACCL:L1B:0210:CAV:FUDGE
RL Cavity design length - constant ACCL:L1B:0210:L N/A
RFREQCavity design frequency - constant ACCL:L1B:0210:FREQ N/A
RIMPEDCavity design shunt impedance - constant ACCL:L1B:0210:IMPED N/A
RPWRDISSCavity dissipated power (W). Calculated by LLRF from Q0 and cavity amplitude. Sent by LLRF to cryo controls.ACCL:L1B:0210:PWRDISS
RQ0Cavity Q0 (unitless), including user fudge factor. This is the value used by HaLO, LLRF calculation of dissipated power, etc. Formula: Q0 = Q0:MEAS * Q0:FUDGEACCL:L1B:0210:Q0
R/WQ0:MEASLast measured cavity Q0 (unitless)ACCL:L1B:0210:Q0:MEAS
R/WQ0:FUDGECavity Q0 fudge factor (unitless). Nominal value of 1. Can be used to adjust Q0 if suspect actual Q0 is not Q0:MEAS, for example due to recent quench.ACCL:L1B:0210:Q0:FUDGE
SRF Interlocks - Per Cavity
 WINTLK_RESET_ALL Reset all latched faults from RFS and Resonance/Interlock chassisACCL:L1B:0210:INTLK_RESET_ALL
 RRFS:INTLK_FIRST Bit mask indicating which interlock fault was first detected by RFS.ACCL:L1B:0210:RFS:INTLK_FIRST N/A
 RRFS:FLTINTLK_FIRST For last captured fault waveform, bit mask indicating which interlock fault was first detected by RFSACCL:L1B:0210:RFS:FLTINTLK_FIRST N/A
RQUENCH_FLT


Cavity quench fault, from RFS chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

ACCL:L1B:0210:QUENCH_FLT
RQUENCH_LTCHACCL:L1B:0210:QUENCH_LTCH
WQUENCH_BYPACCL:L1B:0210:QUENCH_BYP
RQUENCH_BYP_RBVACCL:L1B:0210:QUENCH_BYP_RBV
RQUENCH_CNTTACCL:L1B:0210:QUENCH_CNTT
RQUENCH_CNTYACCL:L1B:0210:QUENCH_CNTY
RQUENCH_CNTACCL:L1B:0210:QUENCH_CNT
RQUENCH_CNTUACCL:L1B:0210:QUENCH_CNTU
RSTEPTEMP_FLT

    

Stepper temperature fault, from Interlock chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

ACCL:L1B:0210:STEPTEMP_FLT
RSTEPTEMP_LTCHACCL:L1B:0210:STEPTEMP_LTCH
WSTEPTEMP_BYP ACCL:L1B:0210:STEPTEMP_BYP
RSTEPTEMP_BYP_RBVACCL:L1B:0210:STEPTEMP_BYP_RBV
RSTEPTEMP_CNTTACCL:L1B:0210:STEPTEMP_CNTT
RSTEPTEMP_CNTYACCL:L1B:0210:STEPTEMP_CNTY
RSTEPTEMP_CNTACCL:L1B:0210:STEPTEMP_CNT
RSTEPTEMP_CNTUACCL:L1B:0210:STEPTEMP_CNTU
RCPLRTEMP1_FLT


Coupler temperature 1 fault, from Interlock chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

ACCL:L1B:0210:CPLRTEMP1_FLT
RCPLRTEMP1_LTCHACCL:L1B:0210:CPLRTEMP1_LTCH
WCPLRTEMP1_BYP ACCL:L1B:0210:CPLRTEMP1_BYP
RCPLRTEMP1_BYP_RBV ACCL:L1B:0210:CPLRTEMP1_BYP_RBV
RCPLRTEMP1_CNTTACCL:L1B:0210:CPLRTEMP1_CNTT
RCPLRTEMP1_CNTYACCL:L1B:0210:CPLRTEMP1_CNTY
RCPLRTEMP1_CNTACCL:L1B:0210:CPLRTEMP1_CNT
RCPLRTEMP1_CNTUACCL:L1B:0210:CPLRTEMP1_CNTU
RCPLRTEMP2_FLT


Coupler temperature 2 fault, from Interlock chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

    		ACCL:L1B:0210:CPLRTEMP2_FLT
RCPLRTEMP2_LTCHACCL:L1B:0210:CPLRTEMP2_LTCH
WCPLRTEMP2_BYPACCL:L1B:0210:CPLRTEMP2_BYP
RCPLRTEMP2_BYP_RBVACCL:L1B:0210:CPLRTEMP2_BYP_RBV
RCPLRTEMP2_CNTTACCL:L1B:0210:CPLRTEMP2_CNTT
RCPLRTEMP2_CNTYACCL:L1B:0210:CPLRTEMP2_CNTY
RCPLRTEMP2_CNTACCL:L1B:0210:CPLRTEMP2_CNT
RCPLRTEMP2_CNTUACCL:L1B:0210:CPLRTEMP2_CNTU
RPLL_FLT

FPGA PLL lock fault, from RFS chassis. Current status, latched status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults. Cannot be bypassed.    

ACCL:L1B:0210:PLL_FLT
RPLL_LTCH ACCL:L1B:0210:PLL_LTCH
RPLL_CNTTACCL:L1B:0210:PLL_CNTT
RPLL_CNTYACCL:L1B:0210:PLL_CNTY
RPLL_CNTACCL:L1B:0210:PLL_CNT
RPLL_CNTUACCL:L1B:0210:PLL_CNTU
RIOCWDOG_FLT


EPICS IOC watchdog fault, from RFS chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

ACCL:L1B:0210:IOCWDOG_FLT
R IOCWDOG_LTCH ACCL:L1B:0210:IOCWDOG_FLT
W IOCWDOG_BYP ACCL:L1B:0210:IOCWDOG_BYP
R IOCWDOG_BYP_RBV ACCL:L1B:0210:IOCWDOG_BYP_RBV 
RIOCWDOG_CNTTACCL:L1B:0210:IOCWDOG_CNTT
RIOCWDOG_CNTYACCL:L1B:0210:IOCWDOG_CNTY
RIOCWDOG_CNTACCL:L1B:0210:IOCWDOG_CNT
RIOCWDOG_CNTUACCL:L1B:0210:IOCWDOG_CNTT
RSSA_FLT


SSA permit fault, from RFS chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

ACCL:L1B:0210:SSA_FLT
R SSA_LTCH ACCL:L1B:0210:SSA_LTCH
W SSA_BYP ACCL:L1B:0210:SSA_BYP
R SSA_BYP_RBV ACCL:L1B:0210:SSA_BYP_RBV
RSSA_CNTTACCL:L1B:0210:SSA_CNTT
RSSA_CNTYACCL:L1B:0210:SSA_CNTY
RSSA_CNTACCL:L1B:0210:SSA_CNT
RSSA_CNTUACCL:L1B:0210:SSA_CNTU
SRF Interlocks - Per Rack (A or B)

RCPLRVAC[A,B]_FLT

   


Coupler vacuum fault, from Interlock chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

    		ACCL:L1B:0200:CPLRVACA_FLT
RCPLRVAC[A,B]_LTCHACCL:L1B:0200:CPLRVACA_LTCH
WCPLRVAC[A,B]_BYP ACCL:L1B:0200:CPLRVACA_BYP
RCPLRVAC[A,B]_BYP_RBV ACCL:L1B:0200:CPLRVACA_BYP_RBV
RCPLRVAC[A,B]_CNTTACCL:L1B:0200:CPLRVACA_CNTT
RCPLRVAC[A,B]_CNTYACCL:L1B:0200:CPLRVACA_CNTY
RCPLRVAC[A,B]_CNTACCL:L1B:0200:CPLRVACA_CNT
RCPLRVAC[A,B]_CNTUACCL:L1B:0200:CPLRVACA_CNTU
RBMLNVAC[A,B]_FLT



Beamline vacuum fault, from Interlock chassis. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

    		ACCL:L1B:0200:BMLNVACA_FLT
RBMLNVAC[A,B]_LTCHACCL:L1B:0200:BMLNVACA_LTCH
WBMLNVAC[A,B]_BYP ACCL:L1B:0200:BMLNVACA_BYP 
RBMLNVAC[A,B]_BYP_RBV ACCL:L1B:0200:BMLNVACA_BYP_RBV
RBMLNVAC[A,B]_CNTTACCL:L1B:0200:BMLNVACA_CNTT
RBMLNVAC[A,B]_CNTYACCL:L1B:0200:BMLNVACA_CNTY
RBMLNVAC[A,B]_CNTACCL:L1B:0200:BMLNVACA_CNT
RBMLNVAC[A,B]_CNTUACCL:L1B:0200:BMLNVACA_CNTU

R

CRYOSUM[A,B]_FLT



Cryo summary fault, from local Cryo PLC. Current status, latched status, bypass command, bypass status, counts of today's faults, yesterday's faults, total faults, a resettable counter's faults.

ACCL:L1B:0200:CRYOSUMA_FLT
RCRYOSUM[A,B]_LTCHACCL:L1B:0200:CRYOSUMA_LTCH
WCRYOSUM[A,B]_BYPACCL:L1B:0200:CRYOSUMA_BYP
RCRYOSUM[A,B]_BYP_RBVACCL:L1B:0200:CRYOSUMA_BYP_RBV
RCRYOSUM[A,B]_CNTTACCL:L1B:0200:CRYOSUMA_CNTT
RCRYOSUM[A,B]_CNTYACCL:L1B:0200:CRYOSUMA_CNTY
RCRYOSUM[A,B]_CNTACCL:L1B:0200:CRYOSUMA_CNT
RCRYOSUM[A,B]_CNTUACCL:L1B:0200:CRYOSUMA_CNTU
   SRF Interlocks - Per Cryomodule - Tentative

 RCRYOSUM_FLT Cryo summary status from local Cryo PLC. Current status ACCL:L1B:0200:CRYOSUM_FLT 
 RHELEVEL_FLT Cryo Helium level status from local Cryo PLC. Current status ACCL:L1B:0200:HELEVEL_FLT
 RHEPRES_FLT Cryo Helium pressure status from local Cryo PLC. Current status ACCL:L1B:0200:HEPRES_FLT
 RCRYOHEARTBEAT_FLT Cryo PLC heartbeat fault. Generated by RF software when cryo data stops updating or updates too slowly ACCL:L1B:0200:CRYOPLC_HEARTBEAT
   SRF Cavity Characterization and Expert Settings
RQLOADEDLoaded QACCL:L1B:0210:QLOADED
RLDCOEFLorentz detuning coefficientACCL:L1B:0210:LDCOEF
RBCOEFMState space B coefficient magnitudeACCL:L1B:0210:BCOEFM
RBCOEFPState space B coefficient phaseACCL:L1B:0210:BCOEFP
RSSA:SLOPESSA curve parameter - slopeACCL:L1B:0210:SSA:SLOPE
RSSA:PEDSSA curve parameter - pedestalACCL:L1B:0210:SSA:PED
RSSA:MINXSSA curve parameter - min x ACCL:L1B:0210:SSA:MINX
RSSA:DRV_MAXMaximum drive to SSA, range 0 to 1. Do not change this directly. It is set by SSA calibration script.ACCL:L1B:0210:DRV_MAX
     
  Waveform Signals

Each SRF cavity has the following waveform signals:

Description PV name, <SIG> in following sectionAmplitude Units Power Units Phase Units
Forward Power FWDsqrt(W) Wdegrees 
Reverse/Reflected Power REVsqrt(W)  Wdegrees 
Cavity Probe CAVMV mWdegrees 
DAC (FPGA internal, input to DAC that drives SSA) DAC% of full DAC scale (% of full DAC scale)^2degrees 
Detune (see below) DFHz  N/A N/A
Drive (RFS chassis loopback) - waveform disabled by defaultDRVsqrt(W)Wdegrees

For SRF systems, these PVs are provided for CAV, FWD, REV, DAC (and DRV only during expert diagnostics/troubleshooting.) Example PVs are for CAV.

R  <SIG>:AWF Signal amplitude waveformACCL:L1B:0210:CAV:AWF
R <SIG>:AMEAN Mean of <SIG>:AWFACCL:L1B:0210:CAV:AMEAN
R <SIG>:ASTD Standard deviation of <SIG>:AWFACCL:L1B:0210:CAV:ASTD
R <SIG>:ARSTD Standard deviation of <SIG>:AWF divided by mean of <SIG>:AWFACCL:L1B:0210:CAV:ARSTD 
R <SIG>:AMIN Minimum of <SIG>:AWFACCL:L1B:0210:CAV:AMIN
R <SIG>:AMAX Maximum of <SIG>:AWFACCL:L1B:0210:CAV:AWF 
 R <SIG>:PWF Signal phase waveformACCL:L1B:0210:CAV:PWF
 R <SIG>:PMEAN Mean of <SIG>:PWFACCL:L1B:0210:CAV:PMEAN 
R <SIG>:PSTD Standard deviation of <SIG>:PWFACCL:L1B:0210:CAV:PSTD 
R  <SIG>:PRSTD Standard deviation of <SIG>:PWF divided by mean of <SIG>:PWFACCL:L1B:0210:CAV:PRSTD  
R <SIG>:PMIN Minimum of <SIG>:PWFACCL:L1B:0210:CAV:PMIN
R <SIG>:PMAX Maximum of <SIG>:PWFACCL:L1B:0210:CAV:PMAX
R <SIG>:PWRWF Signal power waveformACCL:L1B:0210:CAV:PWRWF
R <SIG>:PWRMEAN Mean of <SIG>:PWRWFACCL:L1B:0210:CAV:PWRMEAN
R <SIG>:PWRSTD Standard deviation of <SIG>:PWRWFACCL:L1B:0210:CAV:PWRSTD 
R <SIG>:PWRRSTD Standard deviation of <SIG>:PWRWF divided by mean of <SIG>:PWRWFACCL:L1B:0210:CAV:PWRRSTD
R <SIG>:PWRMIN Minimum of <SIG>:PWRWFACCL:L1B:0210:CAV:PWRMIN
R <SIG>:PWRMAX Maximum of <SIG>:PWRWFACCL:L1B:0210:CAV:PWRMAX
R <SIG>:IWF Signal I waveformACCL:L1B:0210:CAV:IWF
R  <SIG>:QWF Signal Q waveformACCL:L1B:0210:CAV:AWF
R <SIG>:FLTAWF Fault waveform - signal amplitudeACCL:L1B:0210:CAV:FLTAWF
R <SIG>:FLTPWF Fault waveform - signal phaseACCL:L1B:0210:CAV:FLTPWF
Other SRF Waveform Signals:     
RDF:WF Detune frequency waveform. Calculated by software from cavity and forward signals. [Hz]ACCL:L1B:0210:DF:WF
RDF:MEANMean of DF:WFACCL:L1B:0210:DF:MEAN
RDF:STD Standard deviation of DF:WFACCL:L1B:0210:DF:STD 
RDF:MINMinimum of DF:WFACCL:L1B:0210:DF:MIN 
R DF:MAX Maximum of DF:WFACCL:L1B:0210:DF:MAX 
RBW:WF Cavity bandwidth waveform. Calculated by software from cavity and forward signals.  [Hz]ACCL:L1B:0210:BW:WF 
RCTRL:IWFP/I Controller Output I waveform. Calculated by software from cavity and DAC signals. [% of full scale, range -1 to 1]ACCL:L1B:0210:CTRL:IWF 
R CTRL:QWF P/I Controller Output Q waveform. Calculated by software from cavity and DAC signals. [% of full scale, range -1 to 1] ACCL:L1B:0210:CTRL:QWF  
R CTRL:AWF P/I Controller Output amplitude waveform. Calculated by software from cavity and DAC signals. [% of full scale, range -1 to 1] ACCL:L1B:0210:CTRL:AWF  
RCTRL:FLTAWFFault waveform - P/I Controller Output amplitudeACCL:L1B:0210:CTRL:FLTAWF
RCTRL:FLTPWFFault waveform - P/I Controller Output phaseACCL:L1B:0210:CTRL:FLTPWF
R/WACQ_FLT_DELAYFault data trigger control. In % of total waveform data duration. 0% = all data is pre-fault, 100% = all data is post-faultACCL:L1B:0210:ACQ_FLT_DELAY
     
Feedback     
R  AMPFB_GAIN_P_RBV Amplitude feedback proportional gain readback (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_P_RBV
R/W AMPFB_GAIN_P Amplitude feedback proportional gain setting (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_P 
R  AMPFB_GAIN_I_RBV Amplitude feedback integral gain readback (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_I_RBV
R/W AMPFB_GAIN_I Amplitude feedback integral gain setting (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_I 
R  PHAFB_GAIN_P_RBV Phase feedback proportional gain readback (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_P_RBV
R/W PHAFB_GAIN_P Phase feedback proportional gain setting (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_P 
R  PHAFB_GAIN_I_RBV Phase feedback integral gain readback (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_I_RBV
R/W PHAFB_GAIN_I Phase feedback integral gain setting (units not yet determined)ACCL:L1B:0210:AMPFB_GAIN_I 
R  AMPFB_LSUM Amplitude feedback is at lower limit while feedback is active. 0 if true (alarm state), 1 if false (good state)ACCL:L1B:0210:AMPFB_LSUM 
R AMPFB_HSUM Amplitude feedback is at upper limit while feedback is active. 0 if true (alarm state), 1 if false (good state)ACCL:L1B:0210:AMPFB_HSUM 
R AMPFB_SUM Amplitude feedback is at either lower or upper limit while feedback is active. 0 if true (alarm state), 1 if false (good state)ACCL:L1B:0210:AMPFB_SUM 
R PHAFB_LSUM Phase feedback is at lower limit while feedback is active. 0 if true (alarm state), 1 if false (good state)ACCL:L1B:0210:PHAFB_LSUM 
R PHAFB_HSUM Phase feedback is at upper limit while feedback is active. 0 if true (alarm state), 1 if false (good state)ACCL:L1B:0210:PHAFB_HSUM 
RPHAFB_SUMPhase feedback is at either lower or upper limit while feedback is active. 0 if true (alarm state), 1 if false (good state)ACCL:L1B:0210:PHAFB_SUM
RFB_SUMAmplitude or phase feedback is at either lower or upper limit while RFREADYFORBEAM is active. 0 if true (alarm state), 1 if false (good state). This summary's counts of today's faults, yesterday's faults, total faults, a resettable counter faults.ACCL:L1B:0210:FB_SUM
RFB_SUM_CNTTACCL:L1B:0210:FB_SUM_CNTT
RFB_SUM_CNTYACCL:L1B:0210:FB_SUM_CNTY
RFB_SUM_CNTACCL:L1B:0210:FB_SUM_CNT
RFB_SUM_CNTUACCL:L1B:0210:FB_SUM_CNTU

Resonance control


NameDescriptionDescription

SRF Example

(CM2 Cavity 1)SRF Example

Gun/Buncher Example 
R/WSTEP:NSTEPSStepper tuner number of steps per move ACCL:L1B:0210:STEP:NSTEPS
WSTEP:MOV_REQ_NEGRequest stepper tuner move negative STEP:NSTEPS. Write 1 to request ACCL:L1B:0210:STEP:MOV_REQ_NEG
WSTEP:MOV_REQ_POSRequest stepper tuner move positive STEP:NSTEPS. Write 1 to request ACCL:L1B:0210:STEP:MOV_REQ_POS
RSTEP:STATWRDStepper controller status word readback ACCL:L1B:0210:STEP:STATWRD
RSTEP:STATWRD.B0Stepper controller status bit: motor moving; 1 = moving, 0 = not ACCL:L1B:0210:STEP:STATWRD.B0
RSTEP:STATWRD.B2Stepper controller status bit: motor done; 1 = done, 0 = not ACCL:L1B:0210:STEP:STATWRD.B2
RSTEP:STATWRD.B3Stepper controller status bit: at limit B; 1 = at limit, 0 = not. (The limit should never be reached.) ACCL:L1B:0210:STEP:STATWRD.B3
RSTEP:STATWRD.B4Stepper controller status bit: at limit A; 1 = at limit, 0 = not. (The limit should never be reached.) ACCL:L1B:0210:STEP:STATWRD.B4
RSTEP:CTRLWRDStepper controller status word readback ACCL:L1B:0210:STEP:CTRLWRD
RSTEP:CTRLWRD.B5Stepper controller status bit: move direction; 1 if negative, 0 if positive ACCL:L1B:0210:STEP:STATWRD.B0
RSTEP:STATMSG  High-level status message from stepper controller softwareACCL:L1B:0210:STEP:STATMSG 
W PZT:ENABLEPiezo enable/disable control; set to 1 to enable, 0 to disableACCL:L1B:0210:PZT:ENABLE
 RPZT:ENABLESTATPiezo enable/disable status; 1 = enabled, 0 = disabledACCL:L1B:0210:PZT:ENABLESTAT 
W PZT:MODECTRL

Piezo mode control; set to 1 for Integrator (feedback driven by RFS measured detune), 0 for DC control.

Integrator is the correct mode for normal operations.

ACCL:L1B:0210:PZT:MODECTRL
R PZT:MODESTATPiezo mode status; 1 = Integrator, 0 = DCACCL:L1B:0210:PZT:MODESTAT
R PZT:VCalculated piezo voltage ACCL:L1B:0210:PZT:V 
R PZT:DF_RFS Detune measurement sent from RFS to Resonance chassis. This drives the piezo while in Integrator mode.ACCL:L1B:0210:PZT:DF_RFS 
R PZT:DFVALID_RFS 

Detune measurement sent from RFS to Resonance chassis is valid. If it is not valid, the Integrator

will not change the piezo setting

ACCL:L1B:0210:PZT:DFVALID_RFS 
R/W PZT:DAC_SPDC voltage offset setting. Only used while in DC mode.ACCL:L1B:0210:PZT:DAC_SP
R/WPZT:INTEG_SP Optional Integrator setpoint. Can be used to compensate for observed systematic detune offset while in Integrator mode.ACCL:L1B:0210:PZT:INTEG_SP
RPZT:INTEG_SP_RBV Readback of optional Integrator setpoint.ACCL:L1B:0210:PZT:INTEG_SP_RBV
R/WPZT:BIAS

Piezo bias voltage setting. Nominally 25 V. Used to operate piezo away from range limits.

This should not change during normal operations.

ACCL:L1B:0210:PZT:BIAS
RPZT:BIAS_RBV

Readback of piezo bias voltage setting.

ACCL:L1B:0210:PZT:BIAS_RBV
RPZT:INTEG_AT_LIM

Piezo integrator (feedback) is at a limit of its range. This may require moving the stepper to re-center the piezo.

ACCL:L1B:0210:PZT:INTEG_AT_LIM

Deployment and calibration attributes

By default, these should be write-protected during operation


NameDescription

SRF Example

(CM 2 Cavity 1)

 		Gun/Buncher Example 
RAT:GMAXDuring acceptance testing, maximum gradient. [MV/m]ACCL:L1B:0210:AT:GMAXN/A
RAT:AMAXDuring acceptance testing, maximum amplitude. [MV]ACCL:L1B:0210:AT:AMAXN/A
RAT:GUSEDuring acceptance testing, usable gradient. [MV/m]ACCL:L1B:0210:AT:GUSEN/A
RAT:AUSEDuring acceptance testing, usable amplitude. [MV]ACCL:L1B:0210:AT:AUSEN/A
RAT:FEON_GACTDuring acceptance testing, gradient at which field emission begins. [MV/m]ACCL:L1B:0210:AT:FEON_GACTN/A
RAT:FEON_AACTDuring acceptance testing, amplitude at which field emission begins. [MV]ACCL:L1B:0210:AT:FEON_AACTN/A
RAT:LIMITDuring acceptance testing, cavity limiting factor. 0 = Undefined, 1 = Quench, 2 = FE, 3 = SSA trip, 4 = Admin, 5 = RF power, 6 = OtherACCL:L1B:0210:AT:LIMITN/A
RAT:Q0During acceptance testing, cavity Q0 measured at 16 MV/mACCL:L1B:0210:AT:Q0N/A
RAT:QPROBEDuring acceptance testing, cavity probe Q external, coldACCL:L1B:0210:AT:QPROBEN/A
RAT:QHOM_CPLRDuring acceptance testing, Higher Order Mode coupler Q external, coldACCL:L1B:0210:AT:QHOM_CPLRN/A
RAT:QHOM_PICKUPDuring acceptance testing, Higher Order Mode pickup Q external, coldACCL:L1B:0210:AT:QHOM_PICKUPN/A


(from Chris Adolfsen. Garth wonders should this be a calibration attribute rather than physics interface?) Slow tuner start-up position prior to rf turn on - with the piezo voltages zeroed, the cavity would be tuned close to 1.3 GHz after the operating  gradient is established - thus the initial detuning with rf off relative to 1.3 GHz is K*(operating gradient)^2



(from Chris Adolfsen. Garth wonders should this be a calibration attribute rather than physics interface?) Slow tuner park position - this is the position the tuner would be set if one wants to detune the cavity so it does not interact with the beam.



Calibration of the slow tuner (Hz/step) measured in-situ



Calibration of the piezo tuners (Hz/volt) measured in-situ

Per Cryomodule
RSNCryomodule serial numberACCL:L1B:0200:SNN/A

 Signal calibration.

For SRF cavities, the PVs below are provided for CAV, FWD, REV, DRV signals. The SRF PV name examples below use CAV.

 Measured values
R/W  <SIG>:CAL_ADC_10DBMADC counts at 10 dBm. EPICS software uses this to calculate RF power at full scale.ACCL:L1B:0210:CAV:CAL_ADC_10DBM
R/W  <SIG>:CAL_LOSS_CABLEMeasured cable losses used in signal calibration. Positive value in dB.ACCL:L1B:0210:CAV:CAL_LOSS_CABLE
R/W  <SIG>:CAL_LOSS_CPLRMeasured coupler loss used in signal calibration. Positive value in dB.ACCL:L1B:0210:CAV:CAL_LOSS_CPLR
R/W <SIG>:CAL_LOSS_ATTENFixed attenuator used in signal calibration. Positive value in dB.ACCL:L1B:0210:CAV:CAL_LOSS_ATTEN
R/W  <SIG>:CAL_LOSS_OTHERUnattributed measured loss used in signal calibration. Positive value in dB.ACCL:L1B:0210:CAV:CAL_LOSS_OTHER
 EPICS-calculated values 
R <SIG>:CAL_REF_PWRRF power at ADC full scale. [dBm] ACCL:L1B:0210:CAV:CAL_REF_PWR
R  <SIG>:CAL_LOSS_TOTALTotal (of cable, coupler, atten, other) loss used in signal calibration. Positive value in dB. ACCL:L1B:0210:CAV:CAL_LOSS_TOTAL 
R  <SIG>:SCALEFinal calibration scale factor to convert raw ADC counts to amplitude. This also include the beam-based fudge factor ACCL:L1B:0210:CAV:SCALE
For SRF, the signal calibration for Cavity Probe (CAV) can be calculated 2 ways: (1) using the above system losses, power at ADC full scale, and cavity probe Q or (2) calculated from the reverse signal decay. Experts can choose which method they would like to use per cavity
 R/WCAVSCALE_SEL Select between calibration methods: 0 = Qprobe, 1 = RevCalACCL:L1B:0210:CAVSCALE_SEL 
 R/WQPROBE  Cavity probe Q. Used in Qprobe calibration method.ACCL:L1B:0210:QPROBE


Other attributes for operations - Tentative

NameDescription
VChassis power supply voltage
TChassis board temperature
DCSSA enable/disable internal DC power

SSA RF enable, how to distinguish from global RF enable?

PzVout

Output voltage to the piezo tuning motor

PzHzExpected tuning change from PzVout



Expert attributes, not for use on operations screens

NameDescription

Firmware MD5x

BMB7 board serial #


Digitizer board serial #

Chassis serial # and/or Depot number







  • No labels