Table of Conents
p19-0 ring tubes up interactive map
Welcome to the interactive map of the first thermomechanical ring prototype at SLAC.
To explore the ring map in interactive mode, use the buttons on the bottom right of the Gliffy diagram macro. They work inline on Chrome; on Safari, you need to enter full screen. Hover your mouse over the image to get the full screen menu option.
Observations, properties, and measurements by Heater ID
Properties
Quads
| Heater ID: Quads, batch | #1 | #2 | #3 | #4 | #5 | #6 | #7 | #8 | #9 | #10 | Uncertainty | Source |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Length (cm) | 4.110 | 4.106 | 4.102 | 4.101 | 4.105 | 4.101 | 4.101 | 4.108 | 4.105 | 4.103 | ±30 μm | Heaters.xlsx |
| Width (cm) | 4.254 | 4.245 | 4.244 | 4.246 | 4.253 | 4.254 | 4.264 | 4.254 | 4.255 | 4.247 | ±30 μm | Heaters.xlsx |
| Thickness (μm) | 310 | 310 | 315 | 312 | 312 | 315 | 312 | 312 | 312 | 312 | ±5 μm | Heaters.xlsx |
| Resistance when wires first bonded (Ω) | 2.4 | 2.4 | 2.4 | 2.6 | 2.4 | 2.5 | 2.5 | 2.3 | 2.4 | 2.4 | ±0.1 Ω | Heaters.xlsx |
| Resistance: mounted on ring, before spray painting (Ω) | 2-3 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | Heaters.xlsx | |
| Mass (g) | ± 0.001 g | |||||||||||
| Module thickness at center, measured with micrometers (μm) | ||||||||||||
| Wire thicknesses, measured with calipers () |
Triplets
| Heater ID: Singles, batch | #1 | #2 | #3 | #4 | #5 | #6 | #7 | #18 | #9 | Uncertainty | Source |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Length (cm) | ±30 μm | Heaters.xlsx | |||||||||
| Width (cm) | ±30 μm | Heaters.xlsx | |||||||||
| Thickness (μm) | ±5 μm | Heaters.xlsx | |||||||||
| Resistance when wires first bonded (Ω) | 2.4 | 2.4 | ±0.1 Ω | Heaters.xlsx | |||||||
| Resistance: mounted on ring, before spray painting (Ω) | 2-3 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | Heaters.xlsx | |
| Mass (g) | ± 0.001 g | ||||||||||
| Module thickness at center, measured with micrometers (μm) | |||||||||||
| Wire thicknesses, measured with calipers () |
Heater visual inspection
Quads
| Heater ID | #1 | #2 | #3 | #4 | #5 | #6 | #7 | #8 | #9 | #10 |
|---|---|---|---|---|---|---|---|---|---|---|
| Before IPA wash & dry rag polish | ||||||||||
| After IPA wash & dry rag polish | ||||||||||
| Comments |
Triplets
| Heater ID | #1 | #2 | #3 | #4 | #5 | #6 | #7 | #18 | #9 |
|---|---|---|---|---|---|---|---|---|---|
| Before IPA wash & dry rag polish | |||||||||
| After IPA wash & dry rag polish | |||||||||
| Comments |
Loading experience
Quads
| Heater ID | #1 | #2 | #3 | #4 | #5 | #6 | #7 | #8 | #9 | #10 |
|---|---|---|---|---|---|---|---|---|---|---|
| Load date | ||||||||||
| Load position | ||||||||||
Shim testing results | ||||||||||
Expected glue layer thickness (μm) | ||||||||||
100-μm shim | ||||||||||
200-μm shim | ||||||||||
Glue batch | ||||||||||
Syringe ID | ||||||||||
Date dispensed | ||||||||||
Dispensing | ||||||||||
Estimated glue mass per star (mg) | ||||||||||
Averaged mass tests | ||||||||||
Time elapsed since syringe fully thawed | ||||||||||
Minutes module held under vacuum (Hold time) | ||||||||||
Triplets
| Heater ID | #1 | #2 | #3 | #4 | #5 | #6 | #7 | #18 | #9 |
|---|---|---|---|---|---|---|---|---|---|
| Load date | |||||||||
| Load position | |||||||||
Shim testing results | |||||||||
Expected glue layer thickness (μm) | |||||||||
100-μm shim | |||||||||
200-μm shim | |||||||||
Glue batch | |||||||||
Syringe ID | |||||||||
Date dispensed | |||||||||
Dispensing | |||||||||
Estimated glue mass per star (mg) | |||||||||
Averaged mass tests | |||||||||
Time elapsed since syringe fully thawed | |||||||||
Minutes module held under vacuum (Hold time) | |||||||||