Two new detectors EPIX10KA2M and EPIX10KAQUAD are composed from EPIX10KA modules.

Content

Geometry

Plots and comments from Chris Kenny

Comments on epix10ka2m geometry from Chris Kenney

Kenney, Christopher J. 2018-11-12, 2:26 PM             

Guide tube is 7mm outer diameter
We added polyimide tape that was 150 microns thick before application
to the tube.

But a decent estimate would be the mechanical edge-to-edge orthogonal 
separation between sensor edges 7.3 mm. 
We need to add about 1 mm for the guard rings on each sensor

So the orthogonal gap between active pixels on opposing quads across
the beam guide tube should be 8.3 mm

====
Kenney, Christopher J. 2018-11-12, 4:41 PM Blaj, Gabriel;Dubrovin, Mikhail;Kwiatkowski, Maciej             
   
Very rough estimate of the gaps 
There are 3 types of gaps
All are active pixel to active pixel
sensor to sensor ~ 1.6 mm
CB to CB ~ 6.4 mm
sensor to CB ~ 3.9 mm

====
CB = Carrier Board edges
Full camera image below
====
so 384 columns parallel to the balcony (the widest dead gaps)
and 352 orthogonal to the balcony (vertical direction)

epix10ka2m assembly

epix10ka2m-insensitive-gaps.pdf

epix10ka sensor central region between 4 ASICs

The internal gap between four ASICs in sensor,

pixel size 100 x 225 microns in area in both directions.

Metrology map from Chris Kenney

Comments on orientation of epix10ka2m parts from Matt

1-st version of orientation

Weaver, Matt 
Tue 10/9, 3:07 PMO'Grady, Paul Christopher;Dubrovin, Mikhail;Damiani, Daniel S.                
Also, here's some description of the nominal geometry. 
Pay close attention to the last part that describes the positioning of 
ASICs within an "element".  I think this might be different than before.
-Matt

  //
  //   Hard code the array's geometry for now
  //
  //  (Epix10ka2m)
  //         |
  //  Quad 3 | Quad 0      Quad 1 is rotated  90d clockwise
  //  -------+--------     Quad 2 is rotated 180d clockwise
  //  Quad 2 | Quad 1      Quad 3 is rotated 270d clockwise
  //         |
  //
  //  (Quad 0)
  //         |
  //  Elem 0 | Elem 1
  //  -------+--------     No rotations
  //  Elem 2 | Elem 3
  //         |
  //
  //  (Elem 0)
  //         |
  //  ASIC 0 | ASIC 3
  //  -------+--------     No rotations
  //  ASIC 1 | ASIC 2
  //         |

Matt 2018-11-18 orientation chart

Weaver, Matt 2018-11-18, 6:14 PMDubrovin, Mikhail;O'Grady, Paul Christopher
Here's the geometry I'm now using (below).  Note that pixel(0,0) 
for each of the elements below is in the lower right hand corner.
We'll know the quadrant layout for sure when we get the radioactive source exposure on Monday.
  //  (Epix10ka2m)
  //         |
  //  Quad 3 | Quad 0      Quad 1 is rotated  90d clockwise
  //  -------+--------     Quad 2 is rotated 180d clockwise
  //  Quad 2 | Quad 1      Quad 3 is rotated 270d clockwise
  //         |
  //
  //  (Quad 0)
  //         |
  //  Elem 0 | Elem 1
  //  -------+--------     No rotations
  //  Elem 2 | Elem 3
  //         |
  //
The ASICs did not move. The change is that the (352,384) 
array has pixel (0,0) in the lower right hand corner (in ASIC2).
  //  (Elem 0)
  //         |
  //  ASIC 0 | ASIC 3
  //  -------+--------     No rotations
  //  ASIC 1 | ASIC 2
  //         |
  //
  //  (Elem 0-3 pixel array)
  //                    row increasing
  //                          ^
  //                          |
  //                          |
  //  column increasing <-- (0,0)

Preliminary geometry

in /reg/g/psdm/detector/data_test/calib/

/reg/g/psdm/detector/data_test/calib/Epix10ka2M::CalibV1/NoDetector.0:Epix10ka2M.0/geometry/0-end.data @      (epix10ka2m - entire detector)
/reg/g/psdm/detector/data_test/calib/Epix10kaQuad::CalibV1/NoDetector.0:Epix10kaQuad.0/geometry/0-end.data @  (epix10kaquad - one quad)
/reg/g/psdm/detector/data_test/calib/Epix10ka::CalibV1/MecTargetChamber.0:Epix10ka.1/geometry/0-end.data @    (epix10ka - one panel)

copy of geometry files in alignment examples /reg/g/psdm/detector/alignment/

/reg/g/psdm/detector/alignment/epix10ka2m/calib/Epix10ka2M::CalibV1/NoDetector.0:Epix10ka2M.0/geometry/0-end.data
/reg/g/psdm/detector/alignment/epix10kaquad/calib/Epix10kaQuad::CalibV1/NoDetector.0:Epix10kaQuad.0/geometry/0-end.data
/reg/g/psdm/detector/alignment/epix10ka/calib/Epix10ka::CalibV1/MecTargetChamber.0:Epix10ka.1/geometry/0-end.data

EPIX10KA2M and EPIX10KAQUAD