Logbook Engineering run SVT setup

Logbook

2015-02-05

Unpacking, prepping EEL clean room space.

2015-02-06

SVT box installed. Ready to install U-channels.

LV and HV cables unpacked and run from MPOD to flange. LV cables ohmed out at MPOD end with FEB

FEB chiller connected to manifold and tested.

Got ATCA crate from hall.

2015-02-07

MPOD power checked without sense and no detector connected.

MPOD EPICS interface tested, using the IOC on the Hall-B commuters (clonioc1). 

5:00pm
1st power test of the front end boards on the plate without any link. All currents look good.
Layer, DVDD, AVDDP, AVDDN
L1t 0.987, 0.892, 0.249
L2-3t 0.974, 0.902, 0.251
L5t 0.965, 0.882, 0.253
L6t 0.978, 0.884, 0.248
L4t 0.987, 0.889, 0.244
L4b 0.962, 0.869, 0.255
L5b 0.981, 0.875, 0.250
L6b 0.972, 0.875, 0.253
L1b 0.985, 0.876, 0.245
L2-3b 0.959, 0.877, 0.256

5:10pm
Omar found that one of the LV mezzanine card (L5t, bottom screw) was now connecting AGND to the FEB support plate. After debugging turns out that it was the edge of the high-speed mSAS cables that was conducting and touching components on the FEBs.  

5:30pm
L4t and L4b power was swapped on the back of the breakout box (on the flange side). For reference this is patch panel P3 and thus S1 and S2 where swapped. Mapping power to FEBs is ok now.

12:45pm
Wrapped all mSAS cables with kapton tape. Only wrap the parts that cover the FEB plate plus a little extra. The other side needs to be protected by a sleeve, e.g. Halar. 

1215-02-08

* All FEB's sync all hybrids!

====================================================
Physical FEB: 1t Serial: FebFpga: 11 Control/Data Fiber D/H Flange: 3
====================================================
DPM 7, DP 0, Hybrid 3, All sync fine
DPM 7, DP 1, Hybrid 2, All sync fine
DPM 7, DP 2, Hybrid 1, All sync fine
DPM 8, DP 0, Hybrid 0, All sync fine
====================================================

====================================================
Physical FEB: 2-3t Serial: FebFpga: 2 Control/Data Fiber C/G Flange: 2
====================================================
DPM 11, DP 0, Hybrid 3, All sync fine
DPM 11, DP 1, Hybrid 2, All sync fine
DPM 11, DP 2, Hybrid 1, All sync fine
DPM 12, DP 0, Hybrid 0, All sync fine
====================================================

====================================================
Physical FEB: 4t Serial: FebFpga: 6 Control/Data Fiber A/E Flange: 0
Physical FEB: 4t Serial: FebFpga: 1 Control/Data Fiber C/G Flange: 2 (after switch)
====================================================
DPM 12, DP 1, Hybrid 3, All sync fine
DPM 12, DP 2, Hybrid 2, All sync fine
DPM 13, DP 0, Hybrid 1, All sync fine
DPM 13, DP 1, Hybrid 0, All sync fine
====================================================
* Connected high speed cable and powered up. The currents are as follows:
- DIGI: 1.129 A
- ANAP: 1.207 A
- ANAN: .231
* The FEB has a control link but it has several errors. The high speed cable
needs to be switched to a different flange channel.
* Switching the on the flange card didn't resolve the control link errors
present on the flange channel.
* Switched the high speed cable to Flange 2 and control link was fine
====================================================

====================================================
Physical FEB: 5t Serial: FebFpga: 7 Control/Data Fiber A/E Flange: 0
====================================================
DPM 5, DP 1, Hybrid 3, All sync fine
DPM 5, DP 2, Hybrid 2, All sync fine
DPM 6, DP 0, Hybrid 1, Initially saw no sync, after power cycling and
switching hybrids at the crossover, all sync fine.
All that was really required was a power cycle.
DPM 6, DP 1, Hybrid 0, All sync fine
====================================================
* Connected high speed cable and powered up. The currents are as follows:
- DIGI: 1.112 A
- ANAP: 1.173 A
- ANAN: .257
* Connected the hybrids and tried to run through CODA. Ran into the
same issues as before where we can't connect to the DPM's when not
logged in as Ryan.
====================================================

====================================================
Physical FEB: 6t Serial: FebFpga: 8 Control/Data Fiber A/E Flange: 0
====================================================
DPM 4, DP 0, Hybrid 3, All sync fine
DPM 4, DP 1, Hybrid 2, All sync fine
DPM 4, DP 2, Hybrid 1, All sync fine
DPM 5, DP 0, Hybrid 0, All sync fine
====================================================

====================================================
Physical FEB: 1b Serial: FebFpga: 9 Control/Data Fiber D/H Flange: 3
====================================================
DPM 10, DP 0, Hybrid 3, All sync fine
DPM 10, DP 1, Hybrid 2, All sync fine
DPM 10, DP 2, Hybrid 1, All sync fine
DPM 9, DP 2, Hybrid 0, All sync fine
====================================================

====================================================
Physical FEB: 2-3b Serial: FebFpga: 0 Control/Data Fiber C/G Flange: 2
====================================================
DPM 10, DP 3, Hybrid 3, All sync fine
DPM 12, DP 3, Hybrid 2, All sync fine
DPM 13, DP 2, Hybrid 1, All sync fine
DPM 8, DP 3, Hybrid 0, All sync fine
====================================================

====================================================
Physical FEB: 4b Serial: FebFpga: 5 Control/Data Fiber B/F Flange: 1
====================================================
DPM 0, DP 0, Hybrid 3, All sync fine
DPM 0, DP 1, Hybrid 2, All sync fine
DPM 0, DP 2, Hybrid 1, All sync fine
DPM 1, DP 0, Hybrid 0, All sync fine
====================================================
* After power up, tried to write config and there was an error. Power
cycling the FEB didn't help. Restarting the control
server fixed the issue.
====================================================

====================================================
Physical FEB: 5b Serial: FebFpga: 4 Control/Data Fiber B/F Flange: 1
====================================================
DPM 1, DP 1, Hybrid 3, All sync fine
DPM 1, DP 2, Hybrid 2, All sync fine
DPM 2, DP 0, Hybrid 1, All sync fine
DPM 2, DP 1, Hybrid 0, All sync fine
====================================================
* Connected high speed cable and powered up. The currents are as follows:
- DIGI: 1.120 A
- ANAP: 1.160 A
- ANAN: .254
====================================================

====================================================
Physical FEB: 6b Serial: FebFpga: 3 Control/Data Fiber B/F Flange: 1
====================================================
DPM 2, DP 2, Hybrid 3, All sync fine
DPM 3, DP 0, Hybrid 2, All sync fine
DPM 3, DP 1, Hybrid 1, All sync fine
DPM 3, DP 2, Hybrid 0, All sync fine
====================================================