Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Mask Editor is intended for interactive selection of good and bad regions on 2D image and preparation of output files with direct and inversed masks. It works as a basic graphical editor with specific input of the image and output for masks.

Content

Table of Contents

User Interface

User interface of the Mask Editor works in a single window containing three pannelspanels; graphical window, left-hand, and bottom side control bars. Content and functionality of these panels is described below. Most of control buttons have tool tip hints; when coursor cursor stops for a few seconds on control button, a pop-up window uppears with explanation of functionality of this button appears for a few seconds .

Graphical window

Graphical window contains image and spectrum. When cursor moves on image or spectrum, its coordinates are displayed near cursor. Cursor pattern is changed from "cross" to "pointing-finger" when it is located on active form boarder.

Left control bar

Left control bar consists of stack of buttons, which are functionally splitted split for four groups; Forms, Modes, I/O, and SatusStatus, which content and functionality is explained in this section.

Forms

Forms are represented by the geometry objects Rectangle, Circle, Polygon, Wedge, and Line, which can be used to compose the mask positive and negative regions. All forms, except Polygon, are presented by two 2D points each in image coordinate system. Polygon is presented by the N 2D points, where N is a number of vertexes. All forms behave about the same way depending on Mode, as explained below.

Modes

Section Panel of modes contain Zoom, Add, Move, Select, and Remove buttons with functionality literally explained by their names.

...

  • Zoom
    Mode Zoom works for image and

...

  • spectral limits.
    Zoom-in image: left mouse button click-drug-release for desired region of image.
    Set limits for spectrum: left/right mouse button click on desired min/max limit on spectrum.
    Reset to full size: middle mouse button click on image or spectral box or "Reset" button.
  • Add
    Add is an input

...

  • mode for forms.

...


  • Input method for Rectangle, Circle, Wedge, and Line: in mode Add click-drug-release the left mouse button. Two points

...

  • for each form are defined by the click and

...

  • release positions of the mouse.

...

  • Input method for Polygon: the N-1 points are entered by the left mouse button click, while the

...

Mode Move

...

  • Nth point is indicated by the right mouse button click

...

  • , which closes the polygon.
  • Move
    Each form can be moved or edited in this mode;
    in mode Move choose the form, then use left/right mouse button click-drug-release on form boarder to move/edit the form.
  • Select
    Forms can be used as

...

  • regular "positive" for ROI, and

...

  • inversed "

...

  • negative" for blemish mask.
    Select button serves to switch between regular and inversed forms.
    In the Select mode choose the form, then use left mouse button click on form boarder.

...

  • Form color is changed at selection/deselection.
  • Remove
    In the Remove mode choose the form, then use any mouse button click on form boarder.
    As an alternative option, currently active form can be removed by the middle mouse button click on its boarder. The "Clear Forms" button from I/O section removes all forms.

I/O

I/O panel contains a stack of buttons for input/output files and other global procedures as listed below.

  • Load Image
    Loads and displays image from text file. The file name is selected through the standard pop-up dialog window.
  • Load Forms
    Loads and displays forms from text file. The file name is selected through the standard pop-up dialog window.
  • Save Forms
    Saves forms in text file. The file name is selected through the standard pop-up dialog window.
  • Save Mask
    Saves "ROI" (positive) mask in text file. The file name is selected through the standard pop-up dialog window.
  • Save inv-M(ask)
    Saves "blemish" (negative) mask in text file. The file name is selected through the standard pop-up dialog window.
  • Print Forms
    Prints current forms from the list.
  • Clear Forms
    Removes forms from image and from the list.

Status panel

Status panel

Mode Remove

I/O

Masks

Masks can be saved as

  • ROI - positive
  • Blemish - inversed

Satus pannel

Satus pannel is a single button-like pannelpanel, displaying short status messages. Click on any button potentially may change the status panel info. Messages are enforced by colors; green/yellow/red, corresponding to normal/attention/warning status. For "Wait ..." messages, it would be wise not clicking on buttons until the procedure is completed.

Note

Mask evaluation for Polygon and Wedge forms may take up to 5-10s/form. Just wait calm!

Bottom control bar

Bottom control bar contains "Help", "Reset", "Save", "ELog", "Close" buttons, "N bins" editable field, "Grid", and "Log" check boxes.

  • Help
    Shows pop-up windows with help info about navigation. Use scroll bar to read entire help message.
  • Reset
    Restores original image size and spectral limits.
  • Save
    Saves content of graphical window in png file. The file name is selected through the standard pop-up dialog window.
  • ELog
    Serves to submit message in ELog. The content of graphical window will be added as attachment. Destination of the message is selected through the custom pop-up dialog window.
  • Close
    Closes the Mask Editor application.
  • Grid
    On/Off coordinate grid on image and spectrum.
  • Log
    Serves as a switch between linear and log scale.
  • N bins
    "N bins" field can be used to change a number of bins in spectrum. Spectrum will redraw, when edition is ended (press Enter on keyboard or change focus on other field).

How to run Mask Editor

Mask Editor is developed as a part of the integrated data processing environment for XCS time correlation experiments. In this project the Mask Editor is integrated as one of the system GUIs. Also it can be executed as a stand-alone application named med. Stand-alone version of the Mask Editor can launched on any of psana or psexport node using command-line interface, for example, for all default parameters:

Code Block

sit_setup
med

List of optional parameters

Code Block

> med -h
Usage: med [options]

Optional input parameters.

Options:
  -h, --help            show this help message and exit
  -i IFNAME, --fname_imgifname=IFNAME
                        input image file name, default = ./roi-img
  -om OFNAMEMFNAME, --fname_figmfname=OFNAME
MFNAME
                        common path to I/O files with mask, default = ./roi-
             output      png file name for current canvasmask
  -mo MFNAMEOFNAME, --path_maskofname=MFNAME
      OFNAME
                        output png file name for current canvas, default =
                  common path to I/O files with mask./fig.png
  -t TITLE, --title=TITLE
                        initial title of the garphical window, default = Mask
                        editor
  -x XC, --xc=XC        x coordinate of the center for Wedges, default = None
  -y YC, --yc=YC        y coordinate of the center for Wedges, default = None
  -p PICKER, --picker=PICKER
                        distance in pix, where object lineresponce canon bemouse,
 reaced by
                      default = mouse8
  -w LW, --lw=LW        object line width, default = 1
  -c COL, --color=COL   color of the form lines "b"-blue, "k"-black, etc.,
                        default = b
  -v, --verbose         allows print on console, default = True
  -q, --quiet           supress print on console

...

, default = False
  -f, --fexmod          file exchange mode on/off (True/False), default = False

Data format for geometrical forms

Forms can be saved in file, loaded from file and displayed on image, printed on console monitor, and cleared/removed from image. This can be done using simple data representation for each form, which is quite self-explained in case of pront print or text-file format:

Code Block

Form parameters for composition of the mask
Rectangle   48.00   50.00  262.00  380.00 1 b False False
Rectangle  987.00  853.00  255.00  380.00 1 w True False
Wedge  716.76  674.72  541.18  197.61 -171.39  174.59 1 b False False
Wedge  674.48  667.64  585.84  386.69  174.75  186.99 1 b False False
Circle  712.00  674.00  262.00 1 b False False
Circle 1068.00  180.00  112.00 1 b False False
Circle  191.00  898.00  117.00 1 b False False
Circle  752.00 1098.00   53.00 1 w True False
Line  689.79 1252.80  624.50  223.22 1 w True False
Line  829.99 1252.80  244.47  388.46 1 b False False
Line  836.67 1303.98  268.07  541.89 1 w True False
Line  692.02 1315.11  669.35  827.50 1 b False False
Polygon 1 w True False 10     400     373     620    ...
Polygon 1 b False False 6     329     674     683    ...   

File exchange mode

2014-06-12, CorAna V00-00-19, in release ana-0.11.6

In order to interactively communicate between Mask Editor and other application(s) Marcin Sikorski requested to introduce the file exchange mechanism for image and mask. It is assumed that external event processing application periodically supplies averaged image, Mask Editor can load it and use for interactive ROI mask correction, and submit in response the mask, which will be used by the external application. This asynchronous data exchange mechanism was implemented in CorAna.ArrFileExchange class. This algorithm uses numpy arrays with np.save(fname,arr) and arr=np.load(fname) methods. In order to get rid of collisions between reader and writer the "ring-buffer" (a.k.a. "round-robin") exchange mechanism is implemented. Data producer writes files with names enumerated in the ring buffer. During writing data is saved in the file with temporary name. When the file is written, it is renamed to indexed name. This eliminates probability of the read/write collision. Data consumer checks availability of the new data and loads numpy array  from the latest file if necessary.

Interface for class CorAna.ArrFileExchange

Code Block
    #-----------------------
    # code in array producer
    #-----------------------
    afe = ArrFileExchange(prefix='./my-numpy-arr') # one call per object
    arr = ...                                      # supply array here
    afe.save_arr(arr)                              # as many times as you need

    #-----------------------
    # code in array consumer
    #-----------------------
    afe = ArrFileExchange(prefix='./my-numpy-arr') # one call per object
    arr = afe.get_arr_latest()                     # as many times as you need

    # optional method:
    status = afe.is_new_arr_available()            # returns True/False if the new array IS/IS NOT available
                                                   # since last call to arr = afe.get_arr_latest()


Two ArrFileExchange objects for image reader and mask writer are incorporated in the Mask Editor. File exchange mode in the med application can be launched by the command:

med -f -i work/my-roi-img -m work/my-roi-mask

assuming that path to the file directory work/ already exists. Options in this example provide functionality as follows;

  • option -f turns on the file exchange mode,
  • files with images are expected to have names work/my-roi-img-rbn-00#.npy and can be loaded by clicking on the GUI button "Load Image",
  • and files with mask will be saved with names work/my-roi-mask-rbn-00#.npy by clicking on GUI button "Save Mask" or "Save Inv-M". 

External application may communicate with launched med through the code pattern shown below

Code Block
from CorAna.ArrFileExchange import *
...
        # create reader/writer objects with file name prefixes 
        # exactly like in the med command line for opposite party:
        afe_rd = ArrFileExchange(prefix='work/my-roi-mask') 
        afe_wr = ArrFileExchange(prefix='work/my-roi-img')
        ...
	    # image writer
	    image = np.array(...)               # supply numpy array for image
        afe_wr.save_arr(image)              # image writer
        ...
	    # mask reader
        if afe_rd.is_new_arr_available() :  # check that the new data is available
            mask = afe_rd.get_arr_latest()  # mask reader             

Mask Editor can be tested with toy image producer application, for example, launch two applications from different xterm windows:

test_img_gen -n 50 -o work/roi-img;
med -f -i work/my-roi-img -m work/my-roi-mask;

then, click on buttons "Load Image", "Save Mask", or "Save Inv-M" in the MaskEditor GUI.

Image exchange with psana

The CorAna.ArrFileExchanges file exchange algorithm is used in psana module imgalgos.image_save_in_file to generate image files within ring buffer.

Other file browser application

In addition to med, there is a file/image browsing application plims, which options can be seen by the command

plims -h

 

Code Block
[pyimgalgos.image_save_in_file]
source     = DetInfo(MecTargetChamber.0:Cspad2x2.3)
key_in     = cspad2x2_image
ofname     = ./roi-img
mode       = 3
delay_sec  = 1
print_bits = 255

 

Demonstration of features

Plots for

  • Input image
  • Image with drawn forms on it
  • Image for mask with forms on it
  • Image for inversed mask with forms on it
  • Help window
    Image ModifiedImage ModifiedImage ModifiedImage ModifiedImage ModifiedImage Modified

References