Versions Compared

Old Version 2

changes.mady.by.user Peregrine McGehee

Saved on

compared with

New Version Current

changes.mady.by.user Peregrine McGehee

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

PurposeBase PVConnectionpmgrpython deviceCabled?Verified/Homed?
Standard Motors

JJ Slits

Not in questionnaire

4 motors

MXI
MXI HexapodMEC:HEX:02Flange T3 to Hexapod 2 controller top of target chamber.N/A
YesYes
MXI linear stageMEC:USR:MMS:21Micronix PPS-110 stage to Flange B7/H<tbd> to PR60 patch panel MEC:USR:MMS:21 connectionCrystal Y


Zyla 500 mm linear stageMEC:PPL:MMN:24

In-air

Direct cabling to XPS3, Card #8

NewportJJ Slits

MEC:TC1:MMS:[17,18]

MEC:TC1:MMS:[01,02]

T5/2 and T5/8
YesYes

Detectors Checklist (TBD)

Other Devices Checklist

PurposeBase PVConnectionCabled?Operational?
Permissive Signal
Trigger MEC:USR:AIN:9

User timing and firing unit permissive output (+5V 100 microsec pulse) to R62 EK9000, second  KL3404 (card 11), first channel, PV MEC:USR:AIN:9.

KL3404 specs are "4-channel analog input, voltage, ±10 V, 12 bit, single-ended"

May need pulse extended, e.g. with a function generator, for detection by PLC.

Yes

Detectors Checklist 

DetectorDAQ aliasConnectionCabled?In DAQ?
epix10k-540kquad_0
  • Power: Quad 0 vac cable -> Flange B3, Q0 feedthru -> air cable "epix10k quad 0" -> MPOD quad outlet 0
    • Note: vac cable labeled "PDU Cable Epix10k Q0" on quad side but "epix10k quad2" on flange side.
  • Fiber: using "epix10k quad 0" vacuum and air fibers. Flange B2, feedthru pair 0 -> PR60 patch panel quad port 0
YesYes

in-air

Power:

Fiber: 



epix10k-540kquad_1
  • Power:  TBD -> Flange B3, Q2 feedthru -> air cable "epix10k quad 2" -> MPOD quad outlet 1
  • Fiber: using "epix10k quad 21 vacuum and air fibers. Flange B2, feedthru pair 2 -> PR60 patch panel quad port 2
  • Note on vacuum power cables:
    • Using cable "PDU Cable epix10k Q1": Minor alarm on DVDD when ON, HV error when failed to configure in the DAQ.
    • There is a second cable from Phil "epix10k quad 0" that I have not tested. It is on the optical table.
Fiber only, no power.No

in-air

Power:

Fiber: 



epix10k-549kquad_2

in-air

Power:

Fiber: 



epix10k-540kquad_3
  • Power:  Quad 3 vac cable -> Flange B3, Q3 feedthru -> air cable "C01 April 2024" -> MPOD quad outlet 3
  • Fiber: using "epix10k quad 3" vacuum and air fibers. Flange B2, feedthru pair 3 -> PR60 patch panel quad port 3
YesYes

ePix100

SW Epix100a

"epix100a_f"

  • Power: Flange B3, South feedthru -> power cable E1 -> MPOD outlet 1
  • Fiber: using "epix100a epix 1" vacuum and air fibers. Flange D2 (left) -> PR60 patch panel epix port 1 → MTP to daq-mec-cam01
  • MECHome: "Epix 1"
  • DAQ: "epix100a_1_bxrts"
YesYes

ePix100

NE Epix100a

"epix100a_b"

  • Power: Flange B3, North feedthru -> power cable E0 -> MPOD outlet 2
  • Fiber: using "epix100a epix 0" vacuum and air fibers. Flange D2 (upper) -> PR60 patch panel epix port 2 → MTP to daq-mec-cam01
  • MECHome: "Epix 2"
  • DAQ: "epix100a_2_fxrts"
YesYes

in-air

Power:

Fiber: 



Andor Zylazyla

in-air

USB/Fiber extender to daq-mec-cam02

YesYesXRT spectrometerhxsssN/AN/A