2019-10-14 Detector Planning Meeting notes

• JF4M initial shipment received. Power supply talks, cable tests next(?)
• Deep clean completed.
• Hansson: Hiring complete, DAPC approved. Expect arrival Dec/Jan. Need tasking plan.
• Trying to create compelling case for Tixel for September PEC...taking a long time, ongoing.
• ePix100s forwarded to TID for refurb?
• Need firmware on 10k small to test....status?
• SLAC-level Detector Strategy Task Force: Three meetings, presenting to SAC, SPC, and LDAC.
• Got no detector feedback from user's meeting...?
• DAQ rack plinth set received, fit questionable.
• Seismic table mount components received..to be installed.

• LDAC set for Dec. 3-4.
  
  • Status of 2018 recommendations: 18 closed/complete, 13 in work/on track, 3 deferred/rejected (Doc available).
  • NEED:
    • RIXS-CCD need analysis of flux limitations (status?)
    • 'White paper' on zero-suppression tradeoffs (in work).
    • Data analysis on ePix prototypes tested in Run 17.
    • Presentation on Jungfau 4M??

• Development Program: Managed to spend all development funding in FY19.
  
  • Development options green-lighted:
    • Purchased new Cd rad source for testing ePix platform done
    • OK'd outside testing of ePix to ~10krad done, at Sandia
    • ePix dummy bond to Ge to test method and thermal ($70k)
    • ePixHi-Z cold testing ($70k)
    • Purchase of CZT material from Redlen ($15k)
    • Tixel: Design sparse readout architecture ($100k).
    • ePix: Design shingled high-rate camera ($100k)
    • SXR microwave annealing machine ($60k) done, received

Status:

• RA: Time on drawings....progress ongoing. Four of the big 5 are out....still need 3-d part...looking at making two copies to test machining in house....submit by end of week?
  

• PH: Submitted two in-house proposals...one on TID sensors, one on UXI@MEC
• Also one on thin-crystal heating at CXI.
• Need to discuss acquiring sensors from UXI collaboration.
• Need to ask what proper operating temperature is for the RIXS-CCD PCB....how should this be cooled?
• Wiring diagram for Jungfrau (Sameen)
• Need automated check on pedestal levels...Jason left and no one has picked up.....PH to follow up with Silke.
  • Silke to establish a couple of data streams to examine performance on dropped shots etc.
• UXI options? Nothing until next year....Liam here this week.
• EMP testing confusing, un-grounded CSPAD testing this week...
• Mike Brown has set up ePix10k and ePix100 on XCS for software development...not done?
• DAQ can run ePix100, ePix10k, Jungfrau....can't yet save data.
• Need to check with Chris about data reduction from Run 17.
  
  
• KN:
• Getting ready for ePixBig test in-hutch on Wednesday to verify hutch is ready to go in Run 18.
• Need to get Mike and Dan talking to the JF kit...IoC on top of PSI scripts.
• Chicane for Marietta almost ready to install eGun.
• Need to coordinate 4-fiber Wave8 with CDS...single vs multimode.
• Matt Church helping with Wave8 ?? Need to mount close as possible to flange.
• All JF Cables are in workm
• KZ: Draft RIXS CCD procedure completed.
• ePix10k requires new MPODS, working issue
• Status documentation/procedures effort
  
  
• KZ:
• RIXS-CCD Procedure draft complete. Review at next detector meeting??
• RIXS-CCD setup work
• Toolbox organization/reorder scheme.