ASIC level requirements summary
| Requirement | ePixUHR | SparkPix-S | SparkPix-ED  |
|---|---|---|---|
| frame rate | 100kfps | 1Mfps | 1Mfps |
| Power supplies | 2.5V Analog 1.3V (AS/DS/IO) | 2.5V Analog 1.3V (AS/DS/IO) 0.6V (Current sink!) | 1.2V (AS/DS/IO) |
| Power for each supply | ePixUHR - 35 kHz | SparkPix-S: supply/ground and power consumption | t.b.d. |
| Number of GT IOs per ASIC | 8 (outputs) | 8 (outputs) 1 clock in | t.b.d |
| Expected I/O speed | 5.25 Gb/s | 5.25 Gb/s | 10 Gb/s |
Total data bandwidth | 42 Gbit/s | 38 Gbit/s | |
FPGA Selection
Target (2x2 Detector) | Target (6x6 Detector: 1 Mpx) | XCVU160 (-C2104) Virtex Ultrascale | KU15P (-A1760) Kintex Ultrascale+ | VU13P (-A2577) Virtex Ultrascale+ | |
IO (HD I/O, HP I/O) | 52, 364 | 96, 416 | 448 (HP) | ||
IO (GTH ) | ≥ 36 (32 outputs + 4 spares) | 288 | 52 | 44 | 0 |
IO (GTY) | ≥ 12 (Transceivers PGP) | 60(72 for 6 transceivers) | 52 | 32 | 128 |
UltraRam, HBM | 36 Mb, None | 360 Mb, None | |||
Transceiver Speed (GTH, GTY) | > 10 Gbps | GTH 16.3Gb/s GTY 30.5Gb/s Transceivers | GTH 16.3Gb/s GTY 32.75Gb/s Transceivers | GTY 32.75Gb/s Transceivers | |
Size | The PCB width is (preferably) 65 mm (2.56’’) | 47.5x47.5 mm | 42.5 x 42.5 mm | 52.5 x 52.5 mm | |
Cost | 40 k$ | 6-10 k$ | 60-110 k$ | ||
Communication | > 42 Gbps |
System level
| Requirement | Parameters | ||
|---|---|---|---|
| Power supply | 24V consistent with the HR detector | ||
| Mechanical size | We would like to match the ePixHRM board dimensions to reuse cooling Side entrance detector
|
| |
| Digital board | 2.56x5.265" | ||
| Power and communication | 2.56x5.240" | ||
| Carrier | 2.56x1.95 | Can we do it smaller? What is the minimum amount of components that need to leave in this board | |
System level power requirements for carrier (what are the specs for the voltage regulator and what is the number of regulators per power)
| Requirement | Parameters | |
|---|---|---|
| 2.5V | ||
| 1.2V | ||
| 0.6V |
IO
For single ended → check the electrical specification
System level accounting
| Functionality | IO type | Quantity | switching specification |
|---|---|---|---|
| ASIC control (GR, ...) | 2.5V SE | Static | |
| SUGOI | |||
| SACI | |||
| DATA | CLM? | 40 + spares? | 10Gbps |
| System IO | |||
| transceiver | 25Gbps | ||
supporting electronics | |||
| enablels for power | |||
| Slow ADC (current and voltage monitors, temperature sensors...) | |||
| HS ADC | |||
serial number | |||
| HS DAC | |||
| Lower priority needs (R&D on system) | |||
| FPGA to FPGA interconnection | requires GT+specific connector | ||
Goal is to have a decision on the FPGA package and family.
Kintex Ultrascale+ vs Virtex?
Transceiver
Ideal is to reuse the 300Gbps Leap On transceiver from Amphenol, unless we find a replacement that operates with single mode power supply.
Board material
Needs to be FR408HR or better
System level simulation
GT to the ASICs
GT to the transceivers
Power drops
Connectors
| Functionality | IO type | Quantity | Observations |
|---|---|---|---|
| carrier to digital board | 1 | Can we use smaller connectors since the number of data IOs per ASIC reduces from 24 to 10? | |
| Digital to Power and communication | 1 | ||
| Power communication to external power supply | 1 |
Notes:
- FPGA intercommunication
- co-design with the data reduction pipeline
- DFX for streaming pre-processing and eventually microAI, reusable building blocks
Overview
Content Tools