EEL Setup

Fibers were tested in fixed locations on the RTM. To ensure that things are working as expected from this table, they should be placed in the same locations on the RTM according to the 2021 mapping.

Fiber / RTM combination	Status
A	OK
B	OK
C	OK
D	OK
E	OK
F	OK
G	?
H	OK

QA of Flange Board ↔ FE0Bs

FEB	Flange Board (HW)	Flange Channel	I At Boot (AnaN, AnaP, Digi)	I Mod ON	I Mod ON + Config	Ctrl Ch (dpm / ch) (1 is top cob)	Fiber (ctrl / Data)	jTag OK	Feb Address	Data Taking	Comment
L0-1t	2	2	0.242 - 1.212 - 1.250	0.292 - 2.317 - 1.392	0.292 - 2.833 - 1.322	0 / 3	D / H	Y	0	OK
L2-3t	3	0	0.256 - 1.248 - 1.239	0.317 - 2.319 - 1.314	0.313 - 3.112 - 1.313	0 / 8	D / H	Y	2	OK
L5t	0	0	0.236 - 1.216 - 1.287	0.272 - 2.101 - 1.334	0.271 - 2.715 - 1.334	1 / 5	A / E	Y	6	OK
L6t	0	1	0.249 - 1.222 - 1.362	0.313 - 2.743 - 1.434	0.308 - 3.539 - 1.434	1 / 4	A / E	Y	8	OK
L4b ( In EPICS is L4t)	2	1	0.248 - 1.241 - 1.248			0 / 4	C / G	Y	5	NO	Hybrid 1 and Hybrid 3 give check transaction errors at the power up and configuration. Feb issue? Also noticed two HV pins missing.
L4t ( In EPICS is L4b)	1	0	0.252 1.153 1.374	0.307 - 2.8755 - 1.448	0.304 - 3.564 - 1.449	1 / 8	B / F	Y	4	OK
L5b	1	1	0.246 - 1.169 - 1.243	0.306 - 2.242 - 1.346	0.302 - 3.063 - 1.321	1 / 7	B / F	Y	7	OK
L6b	1	2	0.248-1.199-1.278	0.307 - 2.705 -1.345	0.304 - 3.525 - 1.348	1 / 6	B / F	Y	9	OK
L0-1b	2	0	0.241 - 1.284 - 1.313	0.293 - 2.235 - 1.394	0.293 - 2.931 - 1.394	0 / 5	C / G	Y	1	OK
L2-3b	3	1	0.248 - 1.122 - 1.195	0.308 - 2.324 - 1.267	0.305 - 3.153 - 1.267	0 / 7	D / H	Y	3	OK	Timeouts on DPM at first test. After reseating the miniSAS cable (both feb and flange board) data taking was clean

Current Issues with Back-end.

List of issues we observed during local data taking relative to the Back - End.
NOTICE!!! The dpm numbers in the daq map after 7 are off by one. Example: DataDpm[13] in the DAQ Map is hostname dpm14.

Search/Navigation:

Related:

Current Issues with Back-end.