Page History

Fiber:

• B2/#1,#2 
• PR60 E15 Middle #1 
• R62 E33 Right #2
• MTP to daq-mec-pgp02
  • rear
  • upper right side
  • left most fiber port

• Power:

• Quad 0

• vac cable -> Flange B3, Q0 feedthru -> air cable "epix10k quad 0" -> MPOD quad outlet 0
  • Note: vac cable labeled "PDU Cable Epix10k Q0" on quad side but "epix10k quad2" on flange side.
• Fiber: using "epix10k quad 0" vacuum and air fibers. Flange B2, feedthru pair 0 -> PR60 patch panel quad port 0

• Power:  TBD -> Flange B3, Q2 feedthru -> air cable "epix10k quad 2" -> MPOD quad outlet 2
• Fiber: using "epix10k quad 2" vacuum and air fibers. Flange B2, feedthru pair 2 -> PR60 patch panel quad port 2
• Note on vacuum power cables:
  • Using cable "PDU Cable epix10k Q1": Minor alarm on DVDD when ON, HV error when failed to configure in the DAQ.
  • There is a second cable from Phil "epix10k quad 0" that I have not tested. It is on the optical table.

• Power:  Quad 3 vac cable -> Flange B3, Q3 feedthru -> air cable "C01 April 2024" -> MPOD quad outlet 3
• Fiber: using "epix10k quad 3" vacuum and air fibers. Flange B2, feedthru pair 3 -> PR60 patch panel quad port 3

Details worked out with Detectors Group.

Fiber:

• B2/#7,#8
• PR60 E15 Middle #4 
• R62 E33 Right #2
• MTP to daq-mec-pgp02
  • rear
  • upper right side
  • left most fiber port

Power: B3/Quad 3

Fiber:

• B2/#7,#8
• PR60 E15 Middle #4 
• R62 E33 Right #2
• MTP to daq-mec-pgp02
  • rear
  • upper right side
  • left most fiber port

ePix100

SW Epix100a

"epix100a_f"

• Power: Flange B3, South feedthru -> power cable E1 -> MPOD outlet 1
• Fiber: using "epix100a epix 1" vacuum and air fibers. Flange D2 (left) -> PR60 patch panel epix port 1 → MTP to daq-mec-cam01
• MECHome: "Epix 1"
• DAQ: "epix100a_1_bxrts"

ePix100

NE Epix100a

"epix100a_b"

• Power: Flange B3, North feedthru -> power cable E0 -> MPOD outlet 2
• Fiber: using "epix100a epix 0" vacuum and air fibers. Flange D2 (upper) -> PR60 patch panel epix port 2 → MTP to daq-mec-cam01
• MECHome: "Epix 2"
• DAQ: "epix100a_2_fxrts"

in-air

USB/Fiber extender to daq-mec-cam02

Yes

Not tested right now since under regular use

Yes

Not tested right now since under regular use

PVs are: 

•  MEC:XT2-1:BMMON:*
•  MEC:XT2-2:BMMON:*

TBD

Yes

PVs are:

• MEC:QADC:01:CH{0,1,2,3}

B3

ioc-mec-qadc.

Timing fiber connected.

Diode signal into A1 with SMA/Male - SSMC/Female Coaxial Jumper Cable and VLM-83-2W-S+ limiter.

Yes