...
| Name | Description | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| GACT | Measured gradient from cavity probe (MV/m) | |||||||||||||||
| GMAX | Maximum allowable gradient (MV/m) - readback only | |||||||||||||||
| GCAL | Gradient calibration scale factor, nominally 1. Multiply by this when calculating raw register value to set, so increasing GCAL increases output. | |||||||||||||||
| ADES | Operation Amplitude setpoint (MV) | |||||||||||||||
| AACT | Measured amplitude from cavity probe (MV) | |||||||||||||||
| AMAX | Maximum allowable amplitude (MV) | |||||||||||||||
| ACAL | Amplitude calibration scale factor, nominally 1. Multiply by this when calculating raw register value to set, so increasing ACAL increases output. | |||||||||||||||
| PDES | Operation Phase setpoint (degrees, where 0 is on-crest) | |||||||||||||||
| PACT | Measured phase from cavity probe (degrees) | |||||||||||||||
| PREF | a.k.a.gold, phase offset used by LLRF to convert measured phase to one relative to on-crest operation, adjusted by beam phasing (degrees) | |||||||||||||||
| DFDES | Cavity detuning setpoint (Hz) | |||||||||||||||
| DFACT | Detune seen by the resonance system (Hz) | |||||||||||||||
| RFMODECTRL | RF mode control (SEL, SELA, SELAP) | |||||||||||||||
| RFMODE | Readback of current RF mode | |||||||||||||||
| RFCTRL | Cavity on/off control. Off = LLRF drive set to 0. (SSA control will be different.) | |||||||||||||||
| RFReady | Status of RF controls, (Ready, Not Ready) set to ready when control loops are closed and RF is continuous. Or will we ever run with pulsed RF? | |||||||||||||||
| Quench | INTLK_QUENCH | Status showing when a cavity quenches, from interlocks (Normal, Quenched) | ||||||||||||||
| STAT | Status bits in software (define the bits) | |||||||||||||||
| HSTA | Hardware status | |||||||||||||||
| AWF | Gradient waveform from the cavity probe, which is used to calculate GACT (MV/m) | |||||||||||||||
| PWF | Phase waveform from the cavity probe, which is used to calculate PACT (degrees) | |||||||||||||||
| *ERRTRACE | Error waveforms corresponding to waveforms above, captured and put in a separate buffer when a fault is detected (degrees or MV/m) | |||||||||||||||
| Any of the above in I/Q equivalent of Amplitude/Phase | ||||||||||||||||
| FWD | Forward signal from SSA to cavity - amplitude | |||||||||||||||
| FWDPWR | Forward signal | PwrFwd | Forward power from SSA to cavity - power | |||||||||||||
| REV | Reverse signal from cavity - amplitude | |||||||||||||||
| REVPWR | Reverse signal from cavity - power | PwrRev | Reflected/reverse power from cavity | |||||||||||||
| PzWF | Waveforms from tuner piezo motors, useful for finding microphonics. Units TBD. | |||||||||||||||
| ALEM | LEM computed integrated RF amplitude (MV) per cavity and per cryomodule | |||||||||||||||
| PLEM | LEM computed phase (deg) | |||||||||||||||
| EGLEM | LEM computed energy gain (MeV) | |||||||||||||||
| CHLEM | LEM computed chirp (MeV) | |||||||||||||||
| Latching SRF Interlocks | ||||||||||||||||
| INTLK_QUENCH |
Cavity quench fault, from interlock chassis. Current status, latched status, and reset command | |||||||||||||||
| INTLK_QUENCH_LTCH | ||||||||||||||||
| INTLK_QUENCH_RESET | ||||||||||||||||
| INTLK_CPLRVAC |
Coupler vacuum fault, from interlock chassis. Current status, latched status, and reset command | |||||||||||||||
| INTLK_CPLRVAC_LTCH | ||||||||||||||||
| INTLK_CPLRVAC_RESET | ||||||||||||||||
| INTLK_BMLNVAC |
Beamline vacuum fault, from interlock chassis. Current status, latched status, and reset command | |||||||||||||||
| INTLK_BMLNVAC_LTCH | ||||||||||||||||
| INTLK_BMLNVAC_RESET | ||||||||||||||||
| INTLK_STEPTEMP |
Stepper temperature fault, from interlock chassis. Current status, latched status, and reset command | |||||||||||||||
| INTLK_STEPTEMP_LTCH | ||||||||||||||||
| INTLK_STEPTEMP_RESET | ||||||||||||||||
| INTLK_CPLRTEMP |
Coupler temperature fault, from interlock chassis. Current status, latched status, and reset command | |||||||||||||||
| INTLK_CPLRTEMP_LTCH | ||||||||||||||||
| INTLK_CPLRTEMP_RESET | ||||||||||||||||
| INTLK_RESET_ALL | Reset all latched faults from interlock chassis | |||||||||||||||
| Non-Latching SRF Interlocks | ||||||||||||||||
| INTLK_HEPRES | Helium pressure fault, from cryo system PLC | |||||||||||||||
| INTLK_HELEVEL | Helium level fault, from cryo system PLC | |||||||||||||||
| INTLK_CRYOHRTBT | Cryo PLC heartbeat fault. Generated by RF software when cryo data stops updating or updates too slowly | |||||||||||||||
| Waveform Signals | ||||||||||||||||
The PVs below will be provided for each waveform signal. Each cavity has the following waveform signals:
| ||||||||||||||||
| Waveform | <SIG>:AWF | Signal amplitude waveform | ||||||||||||||
Statistics | <SIG>:AMEAN | Mean of <SIG>:AF | ||||||||||||||
| <SIG>:ASTD | Standard deviation of <SIG>:AWF | |||||||||||||||
| <SIG>:AMIN | Minimum of <SIG>:AF | |||||||||||||||
| <SIG>:AMAX | Maximum of <SIG>:AWF | |||||||||||||||
| Waveform | <SIG>:PWF | Signal phase waveform | ||||||||||||||
| Statistics | <SIG>:PMEAN | Mean of <SIG>:PWF | ||||||||||||||
| <SIG>:PSTD | Standard deviation of <SIG>:PWF | |||||||||||||||
| <SIG>:PMIN | Minimum of <SIG>:PWF | |||||||||||||||
| <SIG>:PMAX | Maximum of <SIG>:PWF | |||||||||||||||
| Waveform | <SIG>:PWRWF | Signal power waveform | ||||||||||||||
| Statistics | <SIG>:PWRMEAN | Mean of <SIG>:PWRTRACE | ||||||||||||||
| <SIG>:PWRSTD | Standard deviation of <SIG>:PWRWF | |||||||||||||||
| <SIG>:PWRMIN | Minimum of <SIG>:PWRWF | |||||||||||||||
| <SIG>:PWRMAX | Maximum of <SIG>:PWRWF | |||||||||||||||
| Waveform | <SIG>:ITWF | Signal I waveform | ||||||||||||||
| Waveform | <SIG>:QTWF | Signal Q waveform | ||||||||||||||
...
