Page History
...
Metrolody files from different optical measurements are collected in directories with specific dates under
/reg/g/psdm/<PATHREPO>/detector/alignment/cspad2x2/
...
- CSPad2x2-1.txt Q133 D7A16
- CSPad2x2-2.txt Q110 D3A14
- CSPad2x2-3.txt Q111 D12A18
- CSPad2x2-4.txt Q135 D19A19
- CSPad2x2-5.txt Q022 D15A15
- CSPad2x2-6.txt Q157 Used in Run 6
Calibration types
In 2014 new universal detector geometry software is implemented and documented in the Detector Geometry page. In this approach detector geometry calibration information is located in a single file of type
...
center
- x, y, z center position for each two 2x1 in the detector. Obtained from optical measurement.tilt
- two 2x1-tilt angle for the detector in fractional degree. Obtained from optical measurement.
Note |
---|
Calibration types Type |
...
2013-02-13
CSPAD2x2-1 Q133 D7A16
Metrology file
/reg/g/psdm <PATHREPO>/detector/alignment/cspad2x2/calib-cspad2x2-01-2013-02-13/2013-02-13-CSPAD2X2-1-MEC-Metrology.txt
Quality check
Code Block |
---|
pairsegm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL) pairsegm: 0 2090920902 2090220909 -2 2 -5 -43538 -43539 0 1 1 -0.00006 -0.0032900197 48297 48297 0 -7 7 -1 pairsegm: 1 2090620902 2090220906 -2 2 -2 -43538 -43538 0 0 0.00000 -0.00000 48296 48296 0 -4 0 |
Calibration files
/reg/g/psdm/detector/alignment/cspad2x2/calib-cspad2x2-01-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.1/
geometry/1-end.data
center/1-end.data
tilt/1-end.data
2013-02-13
CSPAD2x2-2 Q110 D3A14
Metrology file
/reg/g/psdm/detector/alignment/cspad2x2/calib-cspad2x2-02-2013-02-13/2013-02-13-CSPAD2X2-2-MEC-Metrology.txt
Quality check
Code Block |
---|
pair: S1 S2 dS1 Old version of quality check: pair: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL) pair: 0 2090520909 2089620902 52 -45 4353643538 43539 43536 -20 -2 1 -0.0000100006 -0.0006600329 4829148297 4829448297 -3 0 9 7 0-1 pair: 1 2090520906 2090520902 -22 2 -22 -2 43540 43538 43536 43538 10 0 6 -0.00051 -0.0289500000 0.00000 4829448296 4829948296 -50 04 4 0 |
Calibration
...
files
<PATHREPO>/reg/g/psdm/detector/alignment/cspad2x2/calib-cspad2x2-0201-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.21/
geometry
...
/1-end.data
center/1-end.data
...
tilt/1-end.data
2013-02-13
CSPAD2x2-
...
2 Q110 D3A14
Metrology file
<PATHREPO>/reg/g/psdm/detector/alignment/cspad2x2/calib-cspad2x2-0302-2013-02-13/2013-02-13-CSPAD2X2-32-MEC-Metrology.txt
Quality check
Code Block |
---|
pairsegm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL) pairsegm: 0 2090720896 2090820905 -5 - 4 -43536 43540 -43536 43545 -2 0 -2 5 -0.0000500066 -0.0026348294 4830248291 48301 3 1 -9 -1 -5 pair0 segm: 1 2090420905 2090720905 421 22 424 22 43538 -43540 43538-43536 -203 6 -203 0.00970 10 -0.5560102895 48299 4829948294 05 -3 0 0 |
Calibration file
/reg/g/psdm/detector/alignment/cspad2x2/calib-cspad2x2-03-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.3/geometry/0-end.data
2013-02-13
CSPAD2x2-4 Q135 D19A19
Metrology file
/reg/g/psdm/detector/alignment/cspad2x2/calib-cspad2x2-04-2013-02-13/2013-02-13-CSPAD2X2-4-MEC-Metrology.txt
Quality check
Code Block |
---|
pair: -4 Old version of quality check: pair: S1 S2 dS1 dS2 S1 S2 L1 dS1 L2 dS2 dL1 dL2 L1 <dS/L> L2 angle(deg) dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL) pair: 0 2090620905 20896 20905 -85 -94 4354043536 4354043536 -2 3 -2 3 -0.0002000001 -0.0111900066 4829748291 4829948294 -23 19 0 pair: 1 2090820905 2089820905 -1222 -22 4354143540 4353843536 1210 96 -0.0003900051 -0.0223702895 4829948294 4829548299 -5 4 100 34 |
Calibration file
/reg/g/psdm
<PATHREPO>/detector/alignment/cspad2x2/
calib-cspad2x2-0402-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.42/geometry/0-end.data
2013-02-13 CSPAD2x2-
...
3 Q111 D12A18
Metrology file
/reg/g/psdm<PATHREPO>/detector/alignment/cspad2x2/calib-cspad2x2-0503-2013-02-13/2013-02-13-CSPAD2X2-53-MEC-Metrology.txt
Quality check
Code Block |
---|
pairsegm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL) pairsegm: 0 20908 20904 20907 5 4 20904 -43540 -43545 2 5 2 43536 43536 -1 -1 0.00005 0.00263 48294 48294 0 0 0 pair: 1 20908 20909 122 123 43540 43545 -61 -56 0.00281 0.16119 48302 48302 0 -1 -5 |
Calibration file
calib-cspad2x2-05-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.5/geometry/0-end.data/reg/g/psdm/detector/alignment/cspad2x2/
2013-02-13
CSPAD2x2-6 Q157
Metrology file
/reg/g/psdm/detector/alignment/cspad2x2/
calib-cspad2x2-06-2013-02-13/2013-02-13-CSPAD2X2-6-MEC-Metrology.txt
Quality check
0 -0.00592 48301 48302 -1 1 5
segm: 1 20907 20904 -421 -424 -43538 -43538 -203 -203 0.55599 48299 48299 0 3 0
Old version of quality check:
pair: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL)
pair: 0 20907 20908 -5 -4 43540 43545 0 5 -0.00005 -0.00263 48302 48301 1 -1 -5
pair: 1 20904 20907 421 424 43538 43538 -203 -203 0.00970 0.55601 48299 48299 0 -3 0 |
Calibration file
<PATHREPO>/detector/alignment/cspad2x2/calib-cspad2x2-03-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.3/geometry/0-end.data
2013-02-13
CSPAD2x2-4 Q135 D19A19
Metrology file
<PATHREPO>/detector/alignment/cspad2x2/calib-cspad2x2-04-2013-02-13/2013-02-13-CSPAD2X2-4-MEC-Metrology.txt
Quality check
Code Block |
---|
segm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 angle(deg) D1 D2 dD d(dS) d(dL)
segm: 0 20905 20906 8 9 -43540 -43540 3 3 -0.01119 48299 48297 2 -1 0
segm: 1 20898 20908 12 22 -43541 -43538 9 12 -0.02237 48295 48299 -4 -10 -3
Old version of quality check:
pair: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL)
pair: 0 20906 20905 -8 -9 43540 43540 3 3 -0.00020 -0.01119 48297 48299 -2 1 0
pair: 1 20908 20898 -12 -22 43541 43538 12 9 -0.00039 -0.02237 48299 48295 4 10 3 |
Calibration file
<PATHREPO>/detector/alignment/cspad2x2/calib-cspad2x2-04-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.4/geometry/0-end.data
2013-02-13
CSPAD2x2-5 Q022 D15A15
Metrology file
<PATHREPO>/detector/alignment/cspad2x2/
calib-cspad2x2-05-2013-02-13/2013-02-13-CSPAD2X2-5-MEC-Metrology.txt
Quality check
Code Block |
---|
segm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 angle(deg) D1 D2 dD d(dS) d(dL)
segm: 0 20904 20904 -2 -2 -43536 -43536 -1 -1 0.00263 48294 48294 0 0 0
segm: 1 20909 20908 -122 -123 -43540 -43545 -56 -61 0.16119 48302 48302 0 1 5
Old version of quality check:
pair: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL)
pair: 0 20904 20904 2 2 43536 43536 -1 -1 0.00005 0.00263 48294 48294 0 0 0
pair: 1 20908 20909 122 123 43540 43545 -61 -56 0.00281 0.16119 48302 48302 0 -1 -5 |
Calibration file
calib-cspad2x2-05-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.5/geometry/0-end.data<PATHREPO>/detector/alignment/cspad2x2/
2013-02-13
CSPAD2x2-6 Q157
Metrology file
<PATHREPO>/detector/alignment/cspad2x2/
calib-cspad2x2-06-2013-02-13/2013-02-13-CSPAD2X2-6-MEC-Metrology.txt
Quality check
Code Block |
---|
segm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 angle(deg) D1 D2 dD d(dS) d(dL)
segm: 0 20900 20903 -59 -56 -43541 -43539 -29 -27 0.07567 48298 48297 1 -3 -2
segm: 1 20977 20979 -49 -47 -43707 -43705 -22 -20 0.06292 48478 48482 -4 -2 -2
Old version of quality check:
|
Code Block |
pair: S1 S2 dS1 dS2 L1 L2 dL1 dL2 <dS/L> angle(deg) D1 D2 dD d(dS) d(dL) pair: 0 20903 20900 59 56 43541 43539 -27 -29 0.00132 0.07567 48296 48297 -1 3 2 pair: 1 20979 20977 49 47 43707 43705 -20 -22 0.00110 0.06292 48481 48477 4 2 2 |
Calibration file
<PATHREPO>/reg/g/psdm/detector/alignment/cspad2x2/calib-cspad2x2-06-2013-02-13/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.0/geometry/0-end.data
2014-04-25 CSPAD2X2-3 (1.0 SN07 D12A18)
Metrology file
/reg/g/psdm<PATHREPO>/detector/alignment/cspad2x2/
calib-cspad2x2-03-2014-04-25/2014-04-25-CSPAD2X2-3-MEC-Metrology.txt
...
Code Block |
---|
Quality check in XY plane: segm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 angle(deg) D1 D2 dD d(dS) d(dL) segm: 0 20979 20982 0 3 -43695 -43689 -2 4 -0.00197 48468 48468 0 -3 -6 segm: 1 20981 20981 123 123 -43701 -43695 51 57 -0.16127 48478 48469 9 0 -6 Quality check in Z: segm: SA LA XSize YSize dZS1 dZS2 dZL1 dZL2 dZSA dZLA ddZS ddZL dZX dZY angXZ(deg) angYZ(deg) dz3(um) segm: 0 20980 -43692 43692 20980 18 5 -2 -15 11 -8 13 13 -8 11 -0.01049 0.03004 -13.001 segm: 1 20981 -43698 43698 20981 -4 -8 0 -4 -6 -2 4 4 -2 -6 -0.00262 -0.01639 -4.000 |
Calibration file
calib-cspad2x2-03-2014-04-25/calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.3/geometry/0-end.data<PATHREPO>/reg/g/psdm/detector/alignment/cspad2x2/
2015-04-02 CSPAD2X2-3 (1.0 SN07 D12A18)
...
Note |
---|
Philip and I inspected the CSPAD 140Ks that we received last week (CSPAD 1,2,3,5): - CSPADs 1, 2 and 5 have the same metrology as that on February 13, 2013. - CSPAD 3 has been fixed meanwhile (initially it contained 2x2 module #111, which is the one in your metrology file). Now its 2x2 module is replaced with #7 (metrology file attached). This metrology file should be applied in all experiments that took place after the service date. To find out this date, we will consult with you further. - CSPAD 4 is only a mechanical assembly (see other e-mail sent a few weeks ago). Thanks, Gabriel and Philip |
Metrology file
/reg/g/psdm/<PATHREPO>/detector/alignment/cspad2x2/calib-cspad2x2-03-2015-04-02/2015-04-02-CSPAD2X2-3-MEC-Metrology.txt
/reg/g/psdm<PATHREPO>/detector/alignment/cspad2x2/calib-cspad2x2-03-2015-04-02/2015-04-02-CSPAD2X2-3-MEC-Metrology.xlsx
...
Code Block |
---|
2015-04-02 13:40:57 (info) CalibManager.GUIMetrology: Quality check in X-Y plane: segm: S1 S2 dS1 dS2 L1 L2 dL1 dL2 angle(deg) D1 D2 dD d(dS) d(dL) Quad 0 segm: 0 20981 20978 -33 -36 -43703 -43708 -17 -22 0.04523 48482 48477 5 3 5 segm: 1 20978 20974 -152 -156 -43707 -43702 -73 -68 0.20189 48474 48480 -6 4 -5 2015-04-02 13:40:57 (info) CalibManager.GUIMetrology: Quality check in Z: segm: SA LA XSize YSize dZS1 dZS2 dZL1 dZL2 dZSA dZLA ddZS ddZL dZX dZY angXZ(deg) angYZ(deg) dz3(um) Quad 0 segm: 0 20979 -43705 43705 20979 -1 31 -37 -5 15 -21 -32 -32 -21 15 -0.02753 0.04097 32.009 segm: 1 20976 -43704 43704 20976 -28 -38 5 -5 -33 0 10 10 0 -33 0.00000 -0.09014 -10.007 |
Calibration file
/alignment/cspad2x2//reg/g/psdm/<PATHREPO>/detector
calib-cspad2x2-03-2015-04-02/
calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.3/
...
- All files for CSPAD2x2 alignment are stored under directory
/alignment/cspad2x2//reg/g/psdm/detector
- Files named as
*-Metrology.xlsx
and*-Metrology.txt
are original metrology and its text version. - Calibration files are located under
<PATHREPO>
/reg/g/psdm/detector/alignment/cspad2x2/calib/
directory. - Calibration files can be deployed in the experimental calib store using file manager in
Calibration Management Tool
...
Example of the path to calibration files in the experimental calib store
Code Block |
---|
/reg/d/psdm/<PATH>/mec/mec73313/calib/CsPad2x2::CalibV1/ MecTargetChamber.0:Cspad2x2.1/<calib-type>/0-end.data ... MecTargetChamber.0:Cspad2x2.1/<calib-type>/0-end.data |
...
Code Block |
---|
0 : CxiDg2.0:Cspad2x2.0 1 : CxiDg2.0:Cspad2x2.1 2 : CxiDg3.0:Cspad2x2.0 3 : CxiSc1.0:Cspad2x2.0 4 : CxiSc2.0:Cspad2x2.0 5 : CxiSc2.0:Cspad2x2.1 6 : CxiSc2.0:Cspad2x2.2 7 : CxiSc2.0:Cspad2x2.3 8 : CxiSc2.0:Cspad2x2.4 9 : CxiSc2.0:Cspad2x2.5 10 : CxiSc2.0:Cspad2x2.6 11 : CxiSc2.0:Cspad2x2.7 12 : CxiSc2.0:Cspad2x2.8 13 : CxiSc2.0:Cspad2x2.9 14 : MecEndstation.0:Cspad2x2.6 15 : MecTargetChamber.0:Cspad2x2.0 16 : MecTargetChamber.0:Cspad2x2.1 17 : MecTargetChamber.0:Cspad2x2.2 18 : MecTargetChamber.0:Cspad2x2.3 19 : MecTargetChamber.0:Cspad2x2.4 20 : MecTargetChamber.0:Cspad2x2.5 21 : SxrBeamline.0:Cspad2x2.2 22 : SxrBeamline.0:Cspad2x2.3 23 : XcsEndstation.0:Cspad2x2.0 24 : XcsEndstation.0:Cspad2x2.1 25 : XcsEndstation.0:Cspad2x2.2 26 : XcsEndstation.0:Cspad2x2.3 27 : XcsEndstation.0:Cspad2x2.4 28 : XppGon.0:Cspad2x2.0 29 : XppGon.0:Cspad2x2.1 30 : XppGon.0:Cspad2x2.2 31 : XppGon.0:Cspad2x2.3 32 : XppGon.0:Cspad2x2.4 |
Software
Access interface to any detector data and calibration parameters is implemented in Python Package Detector.
...
- Package CSPadPixCoords generates and returns the CSPad2x2 pixel coordinates, taking into account geometry alignment parameters, if available in the expected place under /reg/d/psdm/<instrument>/<experiment>/calib directory.
- Module CSPadPixCoords::CSPad2x2ImageProducer produces CSPad2x2 image, accounting for correct geometry, if available.
Calibration files
/alignment/cspad2x2//reg/g/psdm/<PATHREPO>/detector
calib-cspad2x2-03-2015-04-02/
calib/CsPad2x2::CalibV1/MecTargetChamber.0:Cspad2x2.3/
center/0-end.data
tilt/0-end.data
References
<PATHREPO>
- explanation of this path and <PATH>