Current Status
The Good
sYAG
sYAG checked out - sYAG:LI20:2434. Both motion and light works - controlled on profile monitor panel. The camera is CAMR:LI20:100.
USOTR
USOTR checked out - OTRS:LI20:3158. Ladder edm linked to from Profile Monitor panel will work. Camera is CAMR:LI20:101. LED light is set up on the USOTR channel accessible on the profile monitor edm panel.
IPOTR1
IPOTR1 checked out - OTRS:LI20:3180. Profile Monitor panel needs to be updated. Camera is CAMR:LI20:102. LED light is set up on the IPOTR 
channel accessible on the profile monitor edm panel however it isn't illuminating the target very well and will be improved.
DSOTR
DSOTR checked out - OTRS:LI20:3206. Profile Monitor panel needs to be updated. Camera is CAMR:LI20:103. LED light is set up on the DSOTR channel accessible on the profile monitor edm panel.
WDSOTR
| Name | MAD Name | EPICS PV | Camera Type | Lens | Position 1 | Position 2 | Position 3 | Position 4 | Position 5 |
|---|---|---|---|---|---|---|---|---|---|
| PMON | PROF:LI20:45 | PROF:LI20:45 | Manta 125 | Computar 55 | Phosphor | ||||
| SYAG | PROF:LI20:2432 | CAMR:LI20:100 | Manta 125 | Nikkor 105 | YAG w/ITO | Phosphor | |||
| USTHz | OTRS:LI20:3070 | CAMR:LI20:101 | Mako 125 | Nikkor 105 | YAG | Ti disc | Ti foil | Ti foil | |
| USOTR | OTRS:LI20:3158 | CAMR:LI20:102 | Mako 125 | Nikkor 60 | YAG | Ti disc | Ti foil | Ti foil | Ti foil |
IPOTR1 | OTRS:LI20:3180 | CAMR:LI20:103 | Manta 125 | Tokina 100 | Ti disc | ||||
| IPOTR1P | CAMR:LI20:104 | ||||||||
| IPOTR2 | CAMR:LI20:105 | Ti foil | YAG | ||||||
| DSOTR | OTRS:LI20:3206 | CAMR:LI20:106 | Manta 125 | Nikkor 105 | Ti flat | YAG | |||
| WDSOTR | OTRS:LI20:3230 | CAMR:LI20:107 | Manta 95 | Tokina 100 | Ti flat | ||||
| DTOTR2 | CAMR:LI20:300 | Manta 125 | Computar 55 | YAG | Ti flat | ||||
| LFOV | ? | Manta 125 | Nikkor 50 | DRZ | |||||
| PRDMP | PROF:LI20:3475 | CAMR:LI20:108 | Manta 95 | Nikkor 35-70 | Phosphor |
Camera Notes
USTHz
USTHz checked out but there is an issue with not having mechanical limit switches. Soft limits need to be used instead and checked before moving. For the short term, best to ask an expert to verify it is set up properly (C. Clarke, J. Allen, S. Gessner). Negative motion is okay when watching with the camera but real caution needs to be used with positive motion.
USOTR
USOTR currently way zoomed out. Acting as "light detector".
IPOTR1
WDSOTR checked out - OTRS:LI20:3230. Profile Monitor panel needs to be updated. Camera is CAMR:LI20:104. LED light is set up on the IP2A channel IPOTR channel accessible on the profile monitor edm panel.EDM panel but the blue LED doesn't illuminate the target very well and will be improved.
IPOTR2
Working, no notes of note.
DSOTR
Working, no notes of note.
WDSOTR
Working, no notes of note.
DTOTR2
User control only please... This is on MC01 Ch7 (X) and Ch8 (Y). DTOTR_x: Position 0 is out and 98 is in. DTOTR_y: 108 is YAG. CAMR:LI20:105.
...
User control only please... This is on MC01 Ch6. Position >100 is out and 0 is in. CAMR:LI20:107
...
ND 2.00 filter is on a flipper controlled by the Beckhoff Digital IO, channel 21, output 1 (Binary 5V Out) - APC:LI20:EX02:5VOUT_1. Value "ON" = filter in.
Camera is a CMOS only readable right now in B244...
PRDMP (not a user area item but included for completeness)
This is a fixed phosphor screen, no mover. CAMR:LI20:108.
Oven
...
Table Mover
Fully checked out. Left Routinely left with the bypass line in the beam path . Put posts in the way so it won't move out of alignment accidentally. These will remain until MPS is working which will shut off the beam when oven table is in an intermediate state.
The Bad and the Ugly (aka work in progress)
IP Wirescanner 1
Checked out motion but LVDT needs to be set up. Small question over the controls channel to be resolved. PMT3350 and PMT3360 appear offline. Work still needed here.
IP Wirescanner 3
Not checked out. (Note wirescanner #2 is not installed).
unless E-300 has beam time.
Wirescanners
IP Wirescanner 1
Checked out motion controls. PMT3350 and PMT3360 online but likely need to be timed into beam. See Fig 6 of this paper for a photo of the wirescanner card: https://slac.stanford.edu/pubs/slacpubs/16250/slac-pub-16410.pdf
and also this image: https://drive.google.com/file/d/1p0GmxaqgvbNhOM8emSWSLWk186gSE2lc/view?usp=sharing
IP Wirescanner 3
Checked out motion controls. For an unobstructed position, 20 mm appears to be an okay on motor, 28 mm on LVDT. But it actually looks to me from the drawings that it ought to be about 90 mm. PMT3350 and PMT3360 online and likely need to be timed into beam
Note, images of the card can be found here: https://drive.google.com/file/d/1scVopR61fpoo_dhtIH5aFozV2wHd0yiM/view?usp=sharing
Toroids
Tunnel work complete- toroids are connected to long haul cables. Understood to be brought online and calibrated.
Work in Progress
...
IPOTR1P
Motion control is all good. Cables are prepared for the camera. Just don't have cameras on these yet . IPOTR2 is controlled on OTRS:LI20:3202 and as they are not needed and we don't want to irradiate cameras without reason. IPOTR1P is on OTRS:LI20:3175. Cameras currently not needed.
HeNe laser injection
Pneumatic actuator works on OTRS:LI20:3158:PNEUMATIC. Needs to have limit switches fixed though. HeNe set up to be completed..