Page History

...

1. AC Rates (using Timeslot 3 and 6): 0Hz, 1Hz, 10Hz, 30Hz, 60Hz, 90Hz, 110Hz, 119Hz, 120Hz 
2. Fixed Rates: 0Hz, 1Hz ,10Hz, 50Hz, 100Hz, 120Hz, 200Hz, 500Hz, 1KHz, 1.4KHz, 5KHZ, 10KHz, 23KHz, 33KHz(special req. not in Tab 4 from PRD), 46KHz, 93KHz (special req. not in Tab 4 from PRD), 464KHz, 929KHz  

The patterns a1) can be interleaved between multiple destinations (SC_DIAG0, SC_BSYD, SC_HXR, SC_SXR, SC_DASEL) up to max 120Hz total. 

The patterns b2) can also be interleaved between multiple destinations (SC_DIAG0, SC_BSYD, SC_HXR, SC_SXR, SC_DASEL) up to max 929KHz. 

...

1) Access the timing trigger displays

Image RemovedImage Added

$TOOLS/pydm/display/evnt/tprDiag.ui & $TOOLS/pydm/display/evnt/tprDiagExp.ui 

*Add Example to how to open related display tprTrigger

*Autogen display from DB

Image Added

*Fixing undefined macrosImage Removed

2)General TPR Setup:

...

Example = 112597 nsec BPMS Message Dealy set in Diag0

Set through caput!

2b)Setup TPR Trigger

The Triggers are linked to the firmware by the Firmware Engineer, talk to the Firmware Engineer to find out what is associated with each Trigger and then set meaningful names to each trigger  "Desc".

Image Added

*Change the TWID and TDES to enterable fields → Verify that SYS0 and SYS2 does update with Mode switching

*Allow to view NC and SC displaysImage Removed

$TOOLS/pydm/display/evnt/tprDiag.ui

...

AC Rates are  0.5Hz, 1Hz, 5Hz, 10Hz, 30Hz, 60Hz → To achieve 120Hz INCLUDE TIMESLOT MASK TS3 and 6!

*0.5Hz Please review DB → Should that be there?

Image AddedImage Removed

Exp Rate → THIS SECTION NEEDS EDITS! Apologies...

...

3a) Trigger based on a Destination receiving Beam

1MHz + Include Dest

Rate Mode = Fixed

Fixed Rate = 1MHz

Destination Mode =  Include

Destination Mask = Dest Bit

Ch Enabled → Only when you are done configuring, to avoid high undesired triggers on your device!

This will trigger your device in either Fixed rate or AC Rate beam, anytime there is beam.

3b)  Trigger based on Destination and Particular Rate (Device Rate Limited)AC and/or Fixed Rate at a Lower rate than beam rate with Destination Requirement

Fixed Rate Case:

Rate Mode = Fixed

Fixed Rate = 10Hz

Destination Mode =  Include

Destination Mask = Dest Bit

Ch Enabled → Only when you are done configuring, to avoid high undesired triggers on your device!

AC Rate

3c) Trigger based on a particular rate but no destination requirement

Case:

Rate Mode = AC

AC Rate = 10Hz

Destination Mode =  Include

Destination Mask = Dest Bit

Ch Enabled → Only when you are done configuring, to avoid high undesired triggers on your device!Dest Mode = Don't Care

3c)Trigger based on AC and/or Fixed Rate at a Lower a Lower rate than beam rate withOUT Destination Requirement

Fixed Rate Case:

Rate Mode = Fixed

Fixed Rate = 10Hz

Destination Mode =  Don't care

Ch Enabled → Only when you are done configuring, to avoid high undesired triggers on your device!

AC Rate Case:

Rate Mode = AC

AC Rate = 10Hz

Destination Mode =  Don't care

Ch Enabled → Only when you are done configuring, to avoid high undesired triggers on your device!

Image AddedImage Removed

3d)

Trigger on special bits like the Calibration Bit for BPMS → Control Sequence Setup

...

Seq = # and bit = #  & EXCLUDE dest = # this provides the out of time trigger. 

Image Added

3e)Trigger on a SYS BSA Buffer at 1Hz, 10Hz, 100Hz → Control Sequence SetupA) For a specific area