Run Checklist
The following info MUST be checked/reported for every shift
for each run enter in the elogbook
- run number (from RunControl)
- run type (photon data, electrons, positrons, proton and in particular if a test or calibration or pedestal run)
- scaler counts (S0, HW trigger, S0&C1&C2,NotSh&S2,DAQ TRIG) - from Online monitor or directly from scalers in the top NIM crate
- trigger choice (if external verify its setup in the trigger logic and in the BT configuration, if internal make sure you select the right BT configuration)
- synchronization with AD ON or OFF; if OFF take a look at AD plots and comment on anomalies
- table position (check it is automatically entered from the pop-up GUI at start of run)
- particle type (e.g. tagged-photons, full-brem, e, pion, proton, positron)
- MNP17 current settings (if applicable)
- notes (e.g. beam intensity, no-beam time, loss of synchronization, change of configuration such as magnet settings, table position)
for each run monitor in the on-line monitor
- DAQ synchronization (check the diagnostics panel, in particular the top left plot should have hits only in the band +-50ns)
for each run monitor in the AD on-line monitor
- for each chamber check the histogram showing the number of hits, if it shows events with more that 128 hits, it means that the pedestal of the Si chambers of the tagger has shifted and must be refreshed. Do the following:
- take a pedestal run in the ancillary
- refresh the pedestal file for the CU online-monitor and for the AD DAQ
for each shift check the following
- CU temperature, every 2 hours, either monitoring the housekeeping data from RunControl or the CU data-logger, which you can see by looking at VNC monitor on pcglast22
- Cerenkov pressure, once a shift
Things to do during a shift
The following is a more detailed list of duties for shifters.
This is a list of steps to be followed while on shift. Please note that when we change configurations some of the reference plots may also change
...
Ask people on shift if tehre is something else to be done and read the shift log
- any bugs?
- did all runs go through the pipeline? (expert wil help you to use this link)
...
Tasks Scheduled for this shift
Do you know who to call in case of trouble during your shift?
Locate On-call call Expert List
Hardware Status
Familiarize yourself with the PS Control Room
Verify Trigger Hardware Status
- Internal versus External
- Scintilattors are part of the trigger?
- Which combination of triggers is being used?
Verify Ancillary Detector Hardware Status
Verify DAQ/Online Status
- Is Housekeeping running on BTServer (desktop4)?
- Is elogbook running on BTServer (desktop2)?
- Is RunControl running on BTServer (desktop1)?
Verify CU Hardware Status
- Check pressure , temperature and humidity in the CU from PCGlast22** click on button labeled Power Supply on the left of the screen
- Check 28 Volts in the CU from PCGlast22. Current expected ~ 2.6 A
- click on tab labeled Agilent on the bottom center of the screen
- Check Housekeeping in the CU from BTServer Screen 2** click desktop 4 on BTServer screen 1* *
Verify Network Hardware Status
...
Set Table in the Correct Position using this document. Details about the table can be found here
Tune Beam - ONLY IF REQUIRED BY THE PROGRAM - consult an expert if needed
Start and Stop a Run
Start a run
Select a data taking configuration for the CU (see here for details)
End a run
Note: never exceed 100K events in a single run; if you notice problems reduce the number of events/run and increase the number of runs
Online Monitoring
Check GLAST Online Monitoring Pages
- GLobaltabs
- TrenidngTrending
- ACD Page
- Ancillary 1 page
- Ancillary 2 Page
- Ancillary Detail Page
- Statistics Page
- Check TKR, CAl and Statisctics Pages for TEM 1, 2, and 3
- Check the trigger counting rate
Offline Monitoring
Data Taking Configurations
In the
Predictions from MC Simulations
In the
Tune the Beam - Expert
Nice During daytime, the 4th shifter must run the Offline monitor to monitor relevant plots and compare with MC data sets