Contents
| Table of Contents | ||||||
|---|---|---|---|---|---|---|
|
Miscellaneous Parameters
rmem_max
| Code Block | ||
|---|---|---|
| ||
# echo 268435456 > /proc/sys/net/core/rmem_max |
vm.max_map_count
For the pgp driver this parameter needs to be increased in /etc/sysctl.conf
| Code Block | ||
|---|---|---|
| ||
# grep vm /etc/sysctl.conf
vm.max_map_count=1000000
# |
DAQ Setup of DSS/FFB Nodes (LCLS-I)
Link here
CPU Frequency Governor
All daq nodes should run the cpu frequency governor in 'performance' either "ondemand" or "performance" mode.
As of this writing (May 2, 2022) the daq node daq-xpp-cam02 is not running the cpu frequency governor in "performance" mode.It appears to be running in "ondemand" mode, which "tries to use the slowest speed as much as possible, but quickly switches up or down when needed."
The epix10a2m requires "performance" mode for correct operation.
| Code Block | ||||||
|---|---|---|---|---|---|---|
| ||||||
Hi,
For example in /cds/group/pcds/dist/pds/boot/daq-det-pgp01 we have the following:
for f in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor; do
echo "performance" > $f
done
This is set for all the machines that are running an epix10ka2m:
daq-det-pgp01
daq-mec-pgp02
daq-mfx-pgp01
daq-xcs-pgp02
daq-xpp-pgp02
Dan |
| Code Block | ||||||
|---|---|---|---|---|---|---|
| ||||||
$ hostname daq-xpp-cam02 $ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor performance $ =========== $ hostname daq-xpp-dss03 $ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor ondemand $ |
The "ondemand" setting is intended to reduce battery usage for portable devices.
Hyperthreading
The case for enabling hyperthreading
In Progress
powersave
powersave
powersave
powersave
powersave
powersave
$ |
As of this writing (May 4, 2022) two MEC pgp nodes differ in their scaling_governor settings.
| Code Block | ||||||
|---|---|---|---|---|---|---|
| ||||||
-bash-4.2$ hostname
daq-mec-pgp01
-bash-4.2$ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
powersave
-bash-4.2$
==============================
-bash-4.2$ hostname
daq-mec-pgp02
-bash-4.2$ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
performance
performance
performance
performance
performance
performance
performance
performance
performance
performance
performance
performance
performance
performance
performance
performance
-bash-4.2$ |
...
| Code Block | ||||||
|---|---|---|---|---|---|---|
| From: Ford, Christopher <caf@slac.stanford.edu>
Sent: Thursday, March 26, 2015 4:45 PM
To: pcds-daq-l
Subject: SXR: hyperthreading enabled on daq-sxr-cam02 and '03?
Folks,
While testing the Andor camera I learned that some DAQ nodes were known to work better than others for this USB-based device.
Tomy writes, "One example I remember is that daq-sxr-cam01 was okay to run for hours, but ||||||
-bash-4.2$ hostname
daq-xcs-dss03
-bash-4.2$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
-bash-4.2$
============
-bash-4.2$ hostname
daq-mec-dss01
-bash-4.2$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
-bash-4.2$
===========
daq-xpp-dss03
-bash-4.2$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
-bash-4.2$ |
See earlier notes on "CPU Freq Scaling" here.
Hyperthreading
As of this writing (May 6, 2022), hyperthreading is enabled on drp-neh-cmp001 and drp-neh-cmp007 (and perhaps elsewhere).
Arguments for hyperthreading
Ric Claus writes:
I can say that the state of the hyperthreading flag is not important for running with trigger rates of 71 KHz and below, but I’m not ready to say that we can dispense with it for 1 MHz running.
Arguments against hyperthreading
On May 6, 2022, at 5:52 PM, Perazzo, Amedeo <perazzo@slac.stanford.edu> wrote:
I had the rhino thought when we installed drp-srcf so we decided to enable hyperthreading (the AMD one, which has a different name) on the new system and we asked Chris (O'Grady) to give it another try. After Chris' tests we decided there was no value in hyperthreading, even on AMD, and we disabled it entirely on drp-srcf. Chris, do you remember?
On May 6, 2022, Chris O'Grady wrote:
I had forgotten, but you are correct Amedeo. My results (for mpi-psana analysis) are here.
It looks like an early test suggested HT helped, but when I tried to reproduce it later on I couldn’t, so we disabled it. Many years ago I also benchmarked some quantum-chemistry code with/without HT and it didn’t help there either
On March 26, 2015, Chris Ford wrote:
To: pcds-daq-lSubject: SXR: hyperthreading enabled on daq-sxr-cam02 and '03?
Folks,
While testing the Andor camera I learned that some DAQ nodes were known to work better than others for this USB-based device.Tomy writes, "One example I remember is that daq-sxr-cam01 was okay to run for hours, but daq-sxr-cam{02,03}
...
would
...
hang
...
after
...
some
...
minutes."
...
Today
...
I
...
took
...
a
...
closer
...
look,
...
and
...
I
...
noticed
...
that
...
hyperthreading
...
seems
...
to
...
be
...
enabled
...
on
...
daq-sxr-cam02
...
and
...
'03,
...
where
...
Andor
...
fails.
...
Hyperthreading
...
seems
...
to
...
be
...
*disabled*
...
on
...
daq-sxr-cam01,
...
where
...
Andor
...
runs
...
well
...
.
...