...
Expand |
---|
title | KU15P power estimation |
---|
|
|
Expand |
---|
title | KU15P power estimation (no GTY) |
---|
|
Image Added Resources used: 32+12 = 44 GTH Discarding the extra 4 spares we can only use GTH signals, without the requirement of separate MGTY supplies. Even if we run the Amphenol Transceivers at the GTH speed (16.3Gbps), one transceiver gives us 179 Gbps (16.3 Gbps * 11 lanes) of bandwidth, which is enough for the 160Gbps expected by the 2x2 detector |
Expand |
---|
title | ePixUHR 140k 2x2 components |
---|
|
Component | Product number | Operation Voltage | Power consumption | N# I/O needed | Needs substitution? | Quad SPI Configuration Memory | MT25QU01GBBB8E12 | 1.8 V | Max 50 mA | 4 | No, we can use HR pins | JTAG |
| 1.8/1.5/1.2 V |
| 4 | No, we can either use HR or go to 1.2V | Analog Monitor (SlowADC) ADC | ADS1217 | AVDD =3V, DVDD =1.8V | < 1 mA | 7 | Maybe. The datasheet guarantees operation for digital down to 2.7V, in HR250 was put at 1.8. Check if it is fine! | Analog Monitor MUX (x5) | MAX4734 | AVDD =3V | < 1 uA | None | They are controlled by the ADC | Humidity sensor | HIH_5031_001 | 3 V |
| None | No | Thermistor | NTC_NHQM103B375T10 |
|
| None | No | Oscillators | •371 MHz XLL726371.428571I •156 MHz 536FB156M250DG •48 MHz CX3225SB48000D0FPJC1 | 2.5 V |
|
| Both 1.8 V and 2.5V solutions can be found depending on the voltage we want to use | Clock Fanout | SI53340-B-GM | 2.5 / 1.8V |
|
| Now is 2.5, probably can be switch to 1.8, but since its AC-coupled should not matter. Check if we can remove the 2.5 LDO | Clock Jitter cleaner | SI5345_64QFN | VDD = 3.3V, DVDD =1.8V |
| 12 + n. clks |
| Programmable Oscillator | LMK61E2 | 3.3 V |
|
| Used?
| High Speed ADC | AD9249 | 1.8 V | Max 58mW/channel: 58*12 = 700mW | 38 | No | ADC_MON_VCM Buffer | AD8607_MSO8 | 1.8V |
|
|
| Bias DAC (HV Ring) | MAX5443 (DAC) + MAX14611 (Level Shifter) + REF192GS (Voltage reference) | 3.0 V (VCCA) |
| 4 | Maybe? Will the sensors have an HV ring? | ASIC clk fanout | SI53340-B-GM |
|
|
| Probably not needed | HS DAC (Vcalib_p) | MAX5719A(DAC)+ MAX14611 (Level Shifter) + OP213 (Buffer) MAX6126A41+(Vref) | 5V |
|
| Why was this chosen? Do we need the 5 V supply? | Level Shifter for Power controllers | MAX3378EETD (x2) MAX3373E_SOT23_8 (x1) | 1.8V -> 3.3V |
|
|
| Serial number | DS2411R | 1.8V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IO
For single ended → check the electrical specification
...