...
| Code Block | ||
|---|---|---|
| ||
ipmitool-pps -I lan -H <shelfmanager> -t <COB Address> -b 0 -A NONE raw <SLAC_NETFN> <CMD> [DATA_0] [DATA_1] ... [DATA_N]
Where:
<shelfmanager> is the hostname/IP address of the Shelf Manager (ex. shasta-sm)
<COB address> is the IPMB address of the COB board (ex. 0x82, 0x84, 0x86, 0x88, 0x8a, 0x8c)
<SLAC_NETFN> The NetFn for our custom command extensions which is 0x34
<CMD> [DATA_X] is the command to be issued and associated parameter as described below
or in the IPMC console window:
[D0 00 <CMD> [DATA_0] [DATA_1] ... [DATA_N]]
Write to Cluster Element BSI: <CMD> = 0x03
The format for this command is
Offset Length Description
0 1 BAY Mask
1 1 RCE Mask
2 1 Do interrupt (Does Nothing)
3 2 Address
5 2 Length to write
7 N Data to write (if length < 16)
(if length > 16, fill with
incrementing data starting with data)
NOTE: Including Bays w/o RCEs or which are not present
in BAY Mask will not result in an error.
Similarly, including RCEs which are not present or are
currently being reset will not result in an error, nor
will RCEs currently held in reset be released from reset
as a result of issuing this command.
Read from Cluster Element BSI: <CMD> = 0x04
The format for this command is
Offset Length Description
0 1 BAY Number
1 1 RCE Number
2 2 Address
4 2 Length to read (Though 2 bytes long,
IPMI practically limits this to <16)
Read COB Data Board ID PROM: <CMD> = 0x05
The format for this command is
Offset Length Description
0 1 BAY Number
Returns the ID
0 8 MSB -> LSB 8 byte ID
RCE Reset Command: <CMD> = 0x0A
The format for this command is
Offset Length Description
0 1 BAY Mask
1 1 RCE Mask
This command returns
Offset Length Description
0 1 Completion Code
1 1 Mask of Bays with errors
NOTE: Including Bays w/o RCEs or which are not present
in BAY Mask will not result in an error.
Similarly, including RCEs which are not present or are
currently being reset will not result in an error, nor
will RCEs currently held in reset be released from reset
as a result of issuing this command.
Read from RTM EEPROM: <CMD> = 0x0B
The format for this command is
Offset Length Description
0 1 EEPROM Select (0=RTM Fru Info EEPROM, 1=RMB EEPROM)
1 1 Address
2 1 Length to read
Write to RTM EEPROM: <CMD> = 0x0C
The format for this command is
Offset Length Description
0 1 EEPROM Select (0=RTM Fru Info EEPROM, 1=RMB EEPROM)
1 1 Address
2 1 Length to write
3 N Data to write
Raw I2C Read: <CMD> = 0xF7
The format for this command is
Offset Length Description
0 1 I2C Bus
1 1 Device Address (7 bit address)
2 1 Length to read
This command returns
Offset Length Description
0 1 Completion Code
1 N Data read
Raw I2C Write: <CMD> = 0xF8
The format for this command is
Offset Length Description
0 1 I2C Bus
1 1 Device Address (7 bit address)
2 1 Length to write
3 N Data to write
This command returns
Offset Length Description
0 1 Completion Code
I2C Test Command: <CMD> = 0xf6
The format for this command is
Offset Length Description
0 1 The BAY to test I2C devices in
1 1 The expected RCE mask
2 1 The expected Power
This command returns
Offset Length Description
0 1 Completion Code
1 1 Error Code
Get Bay Power Command: <CMD> = 0x0e
The format for this command is
Offset Length Description
0 1 The BAY number
This command returns
Offset Length Description
0 1 Completion Code
1 2 Voltage in mV (ADIN)
3 2 Current in mA
Get Bay Temperatures: <CMD> = 0x0f
The format for this command is
Offset Length Description
0 1 BAY number
1 1 RCE number (optional)
This command returns
Offset Length Description
0 1 Completion Code
1 1 Board Temperature
2 1 Junction Temperature
Get Bay GPIO: <CMD> = 0x12
The format for this command is
Offset Length Description
0 1 BAY number
This command returns
Offset Length Description
0 1 Completion Code
Which of the following is returned depends on which BAY is requested:
For a CMB Bay (0-4)
1 1 RCE Detected Mask
2 1 RCE Reset Mask
3 1 RCE BSI Ready Mask
4 1 RCE FPGA Done Mask
5 1 CMB Voltage OK Mask
6 1 CMB Power Allocation (in 1/5 Watts)
For the CEN Bay
1 1 CEN Voltage OK Mask
2 1 SFP Present Mask
3 1 SFP LOS Mask
For the RTM Bay
1 1 RTM Handle Closed
2 1 RMB Present
3 1 RMB Enable
Get Bay Raw GPIO: <CMD> = 0x140x13
The format for this command is
Offset Length Description
0 1 BAY number
1 1 Register (0=Input, 1=Output, 2=Polarity, 3=Config, 4=Int Mask"
This command returns
Offset Length Description
0 1 Completion Code
1 N Register Values for Bank N
Set Monitor Dump Period: <CMD> = 0x07
The format for this command is
Offset Length Description
0 1 Dump Index [0=BAY, 1=RCE, 2=BSI, 3=SFP, 4=FP_DISP, 5=COB_GPIO, 6=GPIO_FULL, 7=RTM, 8=CEN, 9=I2C, 255=ALL]
1 2 Seconds [0=Never Dump, 0xffff=Default]
Set Monitor Dump Period: <CMD> = 0x08
The format for this command is
Offset Length Description
0 1 Dump Index [0=BAY, 1=RCE, 2=BSI, 3=SFP, 4=FP_DISP, 5=COB_GPIO, 6=GPIO_FULL, 7=RTM, 8=CEN, 9=I2C, 255=ALL]
Returns
0 2 Seconds [0=Never Dump]
Dump Monitor Immediate: <CMD> = 0x09
The format for this command is
Offset Length Description
0 1 Dump Index [0=BAY, 1=RCE, 2=BSI, 3=SFP, 4=FP_DISP, 5=COB_GPIO, 6=GPIO_FULL, 7=RTM, 8=CEN, 9=I2C, 255=ALL]
Fixup FRU Info ID: <CMD> = 0x14
The format for this command is
Offset Length Description
0 1 FRU number
Set FRU Info Asset Tag: <CMD> = 0x15
The format for this command is
Offset Length Description
0 1 FRU number
1 N<=32 Asset Tag (NULL terminated ASCII string
Set Standalone Slot Number: <CMD> = 0x11
The format for this command is
Offset Length Description
0 1 Slot Number
Refresh Shelf Info: <CMD> = 0x0D
The format for this command is
Offset Length Description
N/A N/A There are no arguments to this command
Cold Data Reset: <CMD> = 0xF9
The format for this command is
Offset Length Description
N/A N/A There are no arguments to this command
Set Zombie RCE: <CMD> = 0xFA
The format for this command is
Offset Length Description
0 1 Bay Number
1 1 RCE Number
2 1 Zombie State [0=Not a Zombie, 1=BRAINS!]
When an RCE is marked as a Zombie, the IPMC will not allow it
to hold up the booting of the board. (For example, it will
mark the switch port configuration in the DTM BSI as "Disabled"
if the DPM is not Ready.
|
Supported IPMI/ATCA commands
...