Page History
Optical measurement
Run 5 CSPad2-DSD metrology files from Chris Kenney:
2012-01-10-CSPAD2-Configuration.pptx
2012-01-10-Run5-DSD-Metrology.xlsx
2012-01-10-Run5-DSD-Metrology.txt
2012-01-12-Run5-DSD-Metrology-corrected.xlsx
2012-01-12-Run5-DSD-Metrology-corrected.txt
Procedure and table of results
We calculate
S1 - 1st short side of 2x1
S2 - 2nd short side of 2x1
L1 - 1st long side of 2x1
L2 - 2nd long side of 2x1
...
- All ds1, dl1 are well consistent (within +/-10um) with ds1, dl1, respectively
- Angles of 2x1 are in the range from -0.39 to +0.33 degree.
Configuration parameters
Configuration parameters are shown in number of pixels.
For 2x1 pairs in each quad
Coordinates of the 2x1 centers
- Use the same orientation as in optical measurement, center is calculated as an average of 4 corner coordinates
- All coordinates in pixels
...
Code Block |
---|
X(pixel): 198.46, 198.05, 311.84, 99.32, 628.17, 629.59, 711.73, 499.58, 198.24, 198.03, 311.37, 98.35, 625.63, 626.78, 711.25, 498.41, 198.16, 198.04, 309.53, 96.76, 626.36, 626.53, 711.73, 499.20, 198.36, 198.02, 309.53, 97.25, 627.67, 627.51, 711.80, 499.15, Y(pixel): 307.49, 95.11, 626.06, 627.17, 513.15, 725.70, 198.75, 198.39, 307.48, 95.10, 625.67, 625.63, 510.49, 723.25, 196.42, 196.40, 307.77, 95.14, 625.26, 624.72, 513.51, 725.92, 199.69, 200.90, 307.76, 95.09, 627.28, 628.36, 512.75, 725.08, 199.95, 199.96, Z(pixel): 0.19, 0.22, 0.42, 0.47, 0.25, 0.48, 0.00, 0.17, 0.42, 0.27, 0.57, 0.65, 0.55, 0.82, 0.32, 0.38, 0.05, -0.17, 0.70, 0.50, 0.63, 1.11, 0.20, -0.06, -0.01, 0.00, -0.12, -0.15, -0.08, -0.09, 0.06, 0.03, |
2x1-pair orientation angle (degree) in quads
Code Block |
---|
self.pairInQaudOrient = [ [ 270, 270, 180, 180, 90, 90, 180, 180], [ 270, 270, 180, 180, 90, 90, 180, 180], [ 270, 270, 180, 180, 90, 90, 180, 180], [ 270, 270, 180, 180, 90, 90, 180, 180] ] |
Sensor tilt angle (dergee) from optical measurement
Code Block |
---|
dPhi: -0.02500, 0.00329, -0.16977, -0.13423, -0.32451, -0.25566, 0.02698, 0.31916, -0.02369, 0.00461, 0.24123, 0.06686, -0.22574, -0.26358, -0.16712, 0.16513, -0.03159, 0.01447, 0.00526, 0.33226, -0.17809, 0.10962, -0.26712, -0.19214, -0.12963, 0.00526, -0.23951, -0.22634, 0.23030, 0.08285, 0.05132, 0.06119, |
Quads' alignment
Relative quads' alignment currently can not be performed. It needs in image of rings or wires, which is currently not available for this detector.
Overview
Content Tools