Run 22: L-10177 McBride

See https://confluence.slac.stanford.edu/display/MEC/L-10034+Tear-Down for photographs of in-vacuum cables.

Also see "PR60 (EL 2/3) Stepper Motor Patch Panel" in Hardware Infrastructure.

Planned Schedule

Completed as of 8 April 2024:

Target
Beam Dump

9-11 April 2024:

Monochromator Translation
- use F_XRTS MICOS XYZ cabling
Channel cut tip/tilt
- Assign Newport channels
- 4 motors
Si (5 3 3 ) analyzers (H+V)
- Assign IMS channels
- 6 motors
Epix100 translation stage (vt50)
- Assign IMS channels
- 2 motors
Si (5 3 3) analyzer1 - Z axis (vt50)
- Assign IMS channel
- 1 motor

12 April 2024:

LPL Drive Lenses
- Using existing cabling
- 6 motors - Newport
VISAR Lens
- Using existing cabling
- 3 motors - Newport

Newport Usage

XPS	1	2	3	4	5	6	7	8
1	Questar 1 H	Questar 1 V	Questar 2 H	Questar 2 V	BED 2	BED 1	~~B_XRTS X~~	~~Zyla 500m~~
2			~~B_XRTS Y~~					~~B_XRTS Z~~
3	East Z	East Y	East X	West Z	West Y	West X	Zyla 500m IMS500PP - labeled "no connect"	~~Zyla 500m~~
4	Mono2_H (E)	Mono2_V (E)		VISAR Z	~~Diode Z~~ Mono1_V (W)	~~Diode X~~ Mono1_H (W)	VISAR Y	VISAR X

PR60 (EL 2/3) Stepper Motor Patch Panel - Proposed and As Implemented Use

Green marks the patch panel connections I propose to use (or repurpose) for the 6 Analyzer H/V IMS channels. This will avoid time spent in routing directly into distant racks.

Left (1)

(2)

(3)

(4)

(5)

(6)

(7)

Right (8)

Upper

MEC:USR:MMS:17

tgX

MEC:TC1:MMS:26

ePix100a backward

MEC:TC1:MMS:22

ePix100a forward

MEC:USR:MMS:20

Filter Wheel

Analyzer1_V

MEC:USR:MMS:21

Analyze_Z

MEC:USR:MMS:22

IMA Lens

MEC:USR:MMS:23

Not Used

Analyzer1_H

MEC:USR:MMS:24

Not Used

BAD!

Lower

MEC:USR:MMS:25

Talbot Y

Analyzer2_H

MEC:TC1:MMS:25

Turning Mirror L-R

MEC:USR:CLZ:01

Zyla Focus

Analyzer2_V

MEC:USR:CLF:01

Zyla Vert

Analyzer3_V

N/A

MEC:TC1:MMS:29

Turning Mirror U-D

MEC:TC1:MMS:23

Zyla Scint

Analyzer3_H

Motor Checklist

Purpose	Base PV	Connection	pmgr	python device	Cabled?	Verified/Homed?
Standard Motors
LPL Drive Lenses
East_Z	MEC:PPL:MMN:17	T5/*1, XPS 3/1, ioc-mec-ppl-xps3	Newport	east_z	Yes	Yes
East_Y	MEC:PPL:MMN:18	T5/*2, XPS 3/2, ioc-mec-ppl-xps3	Newport	east_y	Yes	Yes
East_X	MEC:PPL:MMN:19	T5/*3, XPS 3/3, ioc-mec-ppl-xps3	Newport	east_x	Yes	Yes
West_Z	MEC:PPL:MMN:20	T5/*4, XPS 3/4, ioc-mec-ppl-xps3	Newport	west_z	Yes	Yes
West_Y	MEC:PPL:MMN:21	T5/*5, XPS 3/5, ioc-mec-ppl-xps3	Newport	west_y	Yes	Yes
West_X	MEC:PPL:MMN:22	T5/*6, XPS 3/6, ioc-mec-ppl-xps3	Newport	west_x	Yes	Yes
VISAR Lens
VISAR_X	MEC:PPL:MMN:32	VacCable 9, T6/DB25-1, AirCable "XPS DelayStage", XPS 4/8, ioc-mec-ppl-xps4	Newport	visar_x	Yes	Yes
VISAR_Y	MEC:PPL:MMN:31	VacCable 2, T6/DB25-2, AirCable "XPS2 #4", XPS 4/7, ioc-mec-ppl-xps4	Newport	visar_y	Yes	Yes
VISAR_Z	MEC:PPL:MMN:28	VacCable 10, T6/5, AirCable "XPS2 #3/XPS2 #1", XPS 4/3, ioc-mec-ppl-xps4	Newport	visar_z	Yes	Yes
Target
TC_hexapod	IOC:MEC:HEX1	B4/L8	Hexapod	pending ECS-4500 - Getting issue details... STATUS	Yes	Yes
Target_X	MEC:USR:MMS:17	D2/D5 MF? moxa-mec-09:4001 (R62 E15), ioc-mec-usrppl-ims	PLS-85 Sample S	target_x	Yes	Yes
Beam Dump
Zyla_500mm	~~MEC:PPL:MMN:08~~ ~~MEC:PPL:MMN:24~~ ~~MEC:PPL:MMN:23~~ Now back to MEC:PPL:MMN:24	in-air to beam dump, ~~XPS 1/8,~~ ~~ioc-mec-ppl-xps1~~ XPS 3/8, ioc-mec-ppl-xps3	Newport	zyla_z	Yes	Yes
JJ Slits Not in questionnaire 4 motors
JJ Slits	MEC:TC1:MMS:[17,18] MEC:TC1:MMS:[01,02]	T5/2 and T5/8			Yes	Yes
Experiment Specific Motors
Fast Diode Not in questionnaire 2 motors
~~Diode_Z~~	~~MEC:PPL:MMN:29~~	~~VacCable 5, T6/7, AirCable "XPS3 #7", XPS 4/5, ioc-mec-ppl-xps4~~	~~Newport~~	~~diode_z~~
~~Diode_Y~~	~~MEC:PPL:MMN:30~~	~~VacCable 11, Flange B5, port B2, AirCable "XPS1 #4", XPS 4/6, ioc-mec-ppl-xps4~~	~~Newport~~	~~diode_y~~
Monochromator Translation From questionnaire: Mono_[XYZ] 3 motors: MECHome Spectrometer screen
Mono Z ~~FXRTS_X~~	MEC:TC1:MMS:09	D2/D5 MF? digi-mec-07:2111 (R64A E19), ioc-mec-tc1-xuv-ims	XUV X	mono_z	Yes	Yes: to LLS and HLS.
Mono Y ~~FXRTS_Y~~	MEC:TC1:MMS:08	D2/D5 MF? digi-mec-07:2110 (R64A E19), ioc-mec-tc1-xuv-ims	XUV Y	mono_y	Yes	Yes: to LLS and HLS.
Mono X ~~FXRTS_Z~~	MEC:TC1:MMS:07	D2/D5 MF? digi-mec-07:2109 (R64A E19), ioc-mec-tc1-xuv-ims	XUV Z	mono_x	Yes	Yes: to LLS and HLS.
Si (5 3 3) analyzers - Dumb Motors (H + V) From questionnaire: Analyzer[123]_[HV] 6 motors
Analyzer1_H	MEC:USR:MMS:23	T6/#1 Analyzer Cable #1	Original, unused: VT-50-100 New: Faulhber_SA_15_8_141 config (under MEC VT50) with encoders and limit switches disabled.	analyzer1_h	Yes	Yes
Analyzer1_V	MEC:USR:MMS:20	T6/#1 Analyzer Cable #2	Original, unused: Micronix_VT50 New: Faulhber_SA_15_8_141 config (under MEC VT50) with encoders and limit switches disabled.	analyzer1_v	Yes	Yes
Analyzer2_H	MEC:USR:MMS:25	T6/#2 Analyzer Cable #3 Repurposed "Talbot Y" PR 60 patch panel connection.	Original: PLS85 In-Air New: Faulhber_SA_15_8_141 config (under MEC VT50) with encoders and limit switches disabled.	analyzer2_h	Yes	Yes
Analyzer2_V	MEC:USR:CLZ:01	T6/#2 Analyzer Cable #4 Repurposed "Zyla Focus" PR 60 patch panel connection.	Original: Optique Peter Focus New: Faulhber_SA_15_8_141 config (under MEC VT50) with encoders and limit switches disabled.	analyzer2_v	Yes	Yes
Analyzer3_V	MEC:USR:CLF:01	D2c/D5 (verify feedthru) Analyzer Cable #5 Repurposed "Zyla Vert" PR 60 patch panel connection.	Original: Optique Peter Vertical New: Faulhber_SA_15_8_141 config (under MEC VT50) with encoders and limit switches disabled.	analyzer3_v	Yes	Yes
Analyzer3_H	MEC:TC1:MMS:23	D2c/D5 (verify feedthru) Analyzer Cable #6 Repurposed "Zyla Scint" PR 60 patch panel connection.	Original: Crystal Y New: Faulhber_SA_15_8_141 config (under MEC VT50) with encoders and limit switches disabled.	analyzer3_h	Yes	Yes
Si (5 3 3) analyzer1 - Z axis (VT 50) From questionnaire: Analyzer1_Z 1 motors
Analyzer1_Z	MEC:USR:MMS:21	VacCable 6, T5/6 ~~MF? moxa-mec-09:4005 (R62 E15), ioc-mec-tc1-vt50-ims~~	VT-50-100	analyzer1_z	Yes	Yes
Channel cut tip/tilt - Newport (H + V) From questionnaire: Mono1_[HV], Mono2_[HV] 4 motors
Mono1_H (W)	MEC:PPL:MMN:29	B5/B2 Newport 4 Port 4		mono1_h (tip/tilt)	Yes	Yes
Mono1_V (W)	MEC:PPL:MMN:30	B5/B3 Newport 4 Port 5		mono1_v (tip/tilt)	Yes	Yes
Mono2_H (E)	MEC:PPL:MMN:25	B5/B4 Newport 4 Port 1		mono2_h (tip/tilt)	Yes	Yes
Mono2_V (E)	MEC:PPL:MMN:26	B5/B5 Newport 4 Port 2		mono2_v (tip/tilt)	Yes	Yes
ePix100 - Translation stage (VT50) From questionnaire: Detector[12]_Z 2 motors
Detector1_Z (Forward)	MEC:TC1:MMS:22	VacCable 5. T5/5 ~~MF? moxa-mec-09:4005 (R62 E15), ioc-mec-tc1-vt50-ims~~	VT-50-55	epix100f_z	Yes	Test lims.
Detector2_Z (Backward)	MEC:TC1:MMS:26	VacCable 4, T5/4 ~~MF? moxa-mec-09:4005 (R62 E15), ioc-mec-tc1-vt50-ims~~	VT-50-55	epix100b_z	Yes	Test lims.

Detectors Checklist (TBD)

Detector	DAQ alias	Connection	Cabled?	In DAQ?
epix10k-540k	quad_0	Power: Quad 0 vac cable -> Flange B3, Q0 feedthru -> air cable "epix10k quad 0" -> MPOD quad outlet 0 Note: vac cable labeled "PDU Cable Epix10k Q0" on quad side but "epix10k quad2" on flange side. Fiber: using "epix10k quad 0" vacuum and air fibers. Flange B2, feedthru pair 0 -> PR60 patch panel quad port 0	Yes	Yes
epix10k-540k	quad_1	Power: TBD -> Flange B3, Q2 feedthru -> air cable "epix10k quad 2" -> MPOD quad outlet 1 Fiber: using "epix10k quad 21 vacuum and air fibers. Flange B2, feedthru pair 2 -> PR60 patch panel quad port 2 Note on vacuum power cables: Using cable "PDU Cable epix10k Q1": Minor alarm on DVDD when ON, HV error when failed to configure in the DAQ. There is a second cable from Phil "epix10k quad 0" that I have not tested. It is on the optical table.	Fiber only, no power.	No
epix10k-540k	quad_3	Power: Quad 3 vac cable -> Flange B3, Q3 feedthru -> air cable "C01 April 2024" -> MPOD quad outlet 3 Fiber: using "epix10k quad 3" vacuum and air fibers. Flange B2, feedthru pair 3 -> PR60 patch panel quad port 3	Yes	Yes
ePix100	SW Epix100a "epix100a_f"	Power: Flange B3, South feedthru -> power cable E1 -> MPOD outlet 1 Fiber: using "epix100a epix 1" vacuum and air fibers. Flange D2 (left) -> PR60 patch panel epix port 1 → MTP to daq-mec-cam01 MECHome: "Epix 1" DAQ: "epix100a_1_bxrts"	Yes	Yes
ePix100	NE Epix100a "epix100a_b"	Power: Flange B3, North feedthru -> power cable E0 -> MPOD outlet 2 Fiber: using "epix100a epix 0" vacuum and air fibers. Flange D2 (upper) -> PR60 patch panel epix port 2 → MTP to daq-mec-cam01 MECHome: "Epix 2" DAQ: "epix100a_2_fxrts"	Yes	Yes
Andor Zyla	zyla	in-air USB/Fiber extender to daq-mec-cam02	Yes	Yes
VISAR 1	visar_1	Network connection with Windows PC ioc-mec-visar1	Yes	Yes Not tested right now since under regular use
VISAR_2	visar_2	Network connection with WIndows PC ioc-mec-visar2	Yes	Yes Not tested right now since under regular use
Diode/Wave8	PVs are: MEC:XT2-1:BMMON:* MEC:XT2-2:BMMON:* MEC:USR_DIO:)	TBD	Yes	Yes: see ECS-5105 - Getting issue details... STATUS .
Timing diode/QADC134	PVs are: MEC:QADC:01:CH{0,1,2,3}	B3 ioc-mec-qadc. Timing fiber connected. Diode signal into A1 with SMA/Male - SSMC/Female Coaxial Jumper Cable and VLM-83-2W-S+ limiter.	Yes	Yes
XRT spectrometer	hxsss	N/A	N/A

Page tree