28 October 2022: All motors operational.
20 October 2022: Resurveyed status.
Rebooting ioc-mec-ppl-xps2 followed by autoconfig, initialization, and referencing restored:
- Tip #2/Tilt #2 (800 nm) (MEC:PPL:MMN:{10,11})
- 500 mm linear stage (MEC:PPL:MMN:14)
The Zyla focus and rotation were reconnected.
Pending:
- Zyla turret (MEC:USR:CLF:01)
27 September 2022: Physical motion checks will be performing during alignment procedures.
| Device | Motor | Type | Hardware Address | EPICS PV | Notes | Cabled? | Running? | Comments |
|---|---|---|---|---|---|---|---|---|
| Total | 10 | Newport | - | |||||
| 15 | Dumb | all included (IMS + dumb) | ||||||
| SPL delivery | Tip#1 400 nm mirror | Manual | N/A | N/A | TRA 6 mm not functional OAP will be used for steering. | |||
Tilt#1 400 nm mirror | Manual | N/A | N/A | TRA 6 mm not functional OAP will be used for steering. | ||||
Tip#2 800 nm mirror | Newport | XPS 2 Channel 2 | MEC:PPL:MMN:10 | TRA 12 mm | Yes | Yes | ||
Tilt#2 800 nm mirror | Newport | XPS 2 Channel 3 | MEC:PPL:MMN:11 | TRA 12 mm | Yes | Yes | ||
| VT50 | Dumb | moxa-mec-09:4007 | MEC:TC1:MMS:22 | 100 mm | Flange DB15 5 | Yes | Settings for motion were not the right one for this type of stage. We have used previous beamtime VT50-100 settings and it worked fine. | |
| VT50 | Dumb | moxa-mec-09:4008 | MEC:TC1:MMS:26 | 300 mm | Flange DB15 4 (recheck 4/5 swap?) | Yes | Settings for motion were not the right one for this type of stage. We have used previous beamtime VT50-100 settings and it worked fine. | |
| Iris | Dumb | moxa-mec-r62-23:4001 | MEC:USR:MMS:21 | - | Flange DB9 #1 | Yes | Switched user dumb motor channels; verified use of Vacuum Iris parameters. | |
| OAP X | IMS | moxa-mec-08:4011 | MEC:TC1:MMS:16 | OAP Screen; Mono X | Yes | Yes | ||
| OAP Y | IMS | moxa-mec-08:4010 | MEC:TC1:MMS:15 | OAP Screen; Mono Y | Yes | Yes | ||
| OAP Z | IMS | moxa-mec-08:4009 | MEC:TC1:MMS:14 | OAP Screen; Mono Z | Yes | Yes | ||
| Imaging Systems | MFA Z | Newport | XPS 3 Channel 1 | MEC:PPL:MMS:17 | 25 mm | Yes, Flange DB25 *1 | Yes | |
| MFA Y | Newport | XPS 3 Channel 2 | MEC:PPL:MMS:18 | 25 mm | Yes, Flange DB25 *2 | Yes | ||
| MFA X | Newport | XPS 3 Channel 3 | MEC:PPL:MMS:19 | 25 mm | Yes, Flange DB25 *3 | Yes | ||
| PLS85 | Dumb | MEC:USR:MMS:22 | 150 mm, not the target stage | Yes, Flange DB9 #3 | Yes | |||
| Filter wheel | Thorlabs, ethernet controlled | Yes | Yes | See Lasers / Lasers / FilterWheel (under Others). | ||||
| MXI | Linear Z | IMS | moxa-mec-08:4012 | MEC:TC1:MMS:23 | MXI Screen; Analyzer 1 Vert | Flange DB25 (south side of TC): H5. | Yes | Use "Crystal Y" pmgr configuration. |
| Hexapod | PI C-887 | IOC:MEC:HEX:3 | MXI Screen; Analyzer 2 | Yes | Yes | |||
| Not being used for X455/X523. | ||||||||
| Not being used for L-10008 | ||||||||
| Not being used for L-10008 | ||||||||
| Not being used for L-10008 | ||||||||
| XTCS (new) | Linear | Newport | XPS 3 Channel 5 | MEC:PPL:MMN:21 | UTS150PPV6 | Yes | Yes | Success using "default" settings. |
| Rotational |
Dumb |
mec-moxa-09:4001 |
MEC:USR:MMS:25 |
RS40 |
|
Yes | Replaced URS stage not recognized after XTCS removal. Substituted dumb RS40 motor. | |
| Filter Wheel | Dumb | mec-moxa-08:4009 | MEC:USR:MMS:20 | rotation stage + limit switch | Yes | Yes | ||
| Misc. | Linear | Newport | XPS 2 Channel 6 | MEC:PPL:MMN:14 | 500 mm, in air | Yes | Yes | |
| Zyla turret | Dumb | moxa-mec-09:4004 | MEC:USR:CLF:01 | in air | Yes | Yes | Connected. This uses a manual controller. | |
| Zyla focus | Dumb | moxa-mec-09:4003 | MEC:USR:CLZ:01 | in air | Yes | Yes | ||
| Zyla rotation scintillator | Dumb | mox-mec-r62-23:4002 | MEC:USR:MMS:23 | in air | Yes | Yes |