Beam Alignemnt

DescXPS ControllerMotor nameChannelPositionDesc. position
DSHM
OTRS:LI20:3075:MOTR
-37200
/-500
in/out
FrontViewXPS:LI20:MC05Target Mount HorizontalM2-120/-150in/out
FrontViewXPS:LI20:MC05Target Mount VerticalM1-20/-20no change

Ionizer/Shadowgraphy

DescXPS ControllerMotor nameChannelPositionDesc. position
Afterglow injectorXPS:LI20:MC01E12 Afterglow injectorM1+28 mm/ +4 mm/ -46 mmCollision closest to PB/ Focus / collision furthest from PB
Shadowgraphy camera stageXPS:LI20:MC02E14 Shadowgraphy ImagingM1
Moves the camera between MO and LFOV imaging
Microscope objectiveMOC-LI20-MC08PB28 MO Vertical MoverCH3
Picomotor, controls the MO

Laser room

DescXPS ControllerMotor nameChannelPositionDesc. position
HeNe beam blockXPS:LA20:LS24Transport HeNe blockM310 mm/
8 mm
in/out
CW beam blockXPS:LA20:LS24CW laser blockM50 mm/
25 mm
in/out

Main beam block

DescXPS ControllerMotor nameChannelPositionDesc. position
Main beam blockXPS:LI20:MC03C9 Compressor beam blockM3299 mm/ 0mmin/out

E300

For sending laser to foil, equivalent of minimum transmission through main attenuator + RP attenuator in is needed.

DescXPS ControllerMotor nameChannelPositionDesc. position
USHMXPS:LI20:MC03PB10 M2 Removal StageM1

0.5 mm / 41 mm

3.5 mm / 44 mm

2 mm /

42.5 mm

0.5/42.5

in/out (E320 position)
Axicon VerticalXPS:LI20:MC04PB2 Lens VerticalM20.9 mmAxicon beam center overlaps with beam center
Axicon HorizontalXPS:LI20:MC04PB3 Lens HorizontalM310 mmAxicon beam center overlaps with beam center
Axicon zXPS:LI20:MC04PB1 Lens Z Position StageM10Position for Axicon

E305

DescXPS ControllerMotor nameChannelPositionDesc. position
Axilens zXPS:LI20:MC04PB1 Lens Z Position StageM120Position for Axilens
Axilens VerticalXPS:LI20:MC04PB2 Lens VerticalM2

0/100

in/out

Axicon beam center overlaps with beam center
Axilens HorizontalXPS:LI20:MC04PB3 Lens HorizontalM3

5.899

6.299 mm

8.57

Axicon beam center overlaps with beam center
USHMXPS:LI20:MC03PB10 M2 Removal StageM1

0.5 mm / 41 mm

3.5 mm / 44 mm

0.5/42.5

in/out (E320 position)

EOS

DescXPS ControllerMotor nameChannelPositionDesc. position
EOS removalXPS:LI20:MC04PB4 EOS Assembly RemovalM410.7 mm/ 50mmin/out












Target assembly

DescXPS ControllerMotor nameChannelPositionDesc. position
Target Assembly VerticalXPS:LI20:MC05PB7 Target Mount VerticalM180Clear in combination with horizontal
Target Assembly HorizontalXPS:LI20:MC05PB8 Target Mount HorizontalM2-150Clear in combination with vertical








E320 assembly

Attention: the alignment target can crash with multiple items. Please contact E-320 if you don't know the procedures.

DescXPS ControllerMotor nameChannelPositionDesc. positionLast update
USHMXPS:LI20:MC03PB10 M2 Removal StageMC03, M1

OAPs in: 42.5 

40.94  40.524

laser vector alignment: 0.5

(cross-check with 305 value above)

E-320 position: mirror on the right side of the e-beam, steering laser onto 1st OAPApril 30, 2024

Alignment Target Vertical

UP/DOWN

XPS:LI20:MC10PB11 SFQED Target VerticalMC10, M10-90
48.35

highest position / lowest position / out position when OAP is IN / YAG in position

ATTENTION: collisions possible, follow exact procedure, check target position before moving OAPs / MO tower

DON'T GO LARGER THAN 90 EVER


http://physics-elog.slac.stanford.edu/facetelog/show.jsp?dir=/2024/17/24.04&pos=2024-04-24T23:48:34

April 24, 2024
MO Tower Mover IN/OUTXPS:LI20:MC10PB12 SFQED Tower MoverMC10, M2

-95/0

IN position to look at focal spot.


Clear (retracted), also home position, needs to be done before retracting SFQED assembly

December 14, 2022
OAP Assembly IN/OUTXPS:LI20:MC10PB16 SFQED Assembly RemovalMC10, M3116 113.53 113.114 / 0

IN position to focus main beam.

Clear (retracted), also home positions, needs MO Tower to move out first, also needs Alignment target to move upwards first

April 30, 2024
Elliptical mirror/M3 IN/OUTXPS:LI20:MC10PB17 Elliptical mirror moverMC10, M4Positive limit switch/negative limit switch + 7

Out position. Configuration is 'SetCurrentPositionAsHome',so need to drive all the way to positive limit switch to ensure driven out.

In position. Drive all the way to negative end for IN position.


PB18 Focus Imaging VerticalXPS:LI20:MC10PB18 Focus Imaging VerticalMC10, M50.427Home at current position (0). Motor should not be touched or moved, should be clear in any case.
Foils vertical moverXPS:LI20:MC05
MC05, M180 -17.2 (foils in for beam vector alignment)needed only for beam-vector alignment (M1/M2)November 8, 2023
Foils horizontal moverXPS:LI20:MC05
MC05, M2-95  -120 (foils in for beam vector alignment)needed only for beam-vector alignment (M1/M2)November 8, 2023

December 14, 2022: http://physics-elog.slac.stanford.edu/facetelog/show.jsp?dir=/2022/50/14.12&pos=2022-12-14T23:59:00

April 24, 2024 E320 OAP swap and new motor positions: http://physics-elog.slac.stanford.edu/facetelog/show.jsp?dir=/2024/17/24.04&pos=2024-04-24T23:48:34

Safely retracting E-320 assembly and setting up to clear e-beam/laser will be:

  • Drive PB12 SFQED Tower Mover to 0 (home)
  • Drive PB11 SFQED Target Vertical to 0 (home)
  • Drive PB16 SFQED Assembly Removal to 0 (home)
  • Drive PB11 SFQED Target Vertical to 90
  • Drive PB17 Elliptical mirror mover to most positive end

Note: TRA motors on MC10 currently do not work in EPICS (position is shown correctly). Drive through XPS web interface.

  • No labels