Assume PREFIX = RFOF:SYS0:00 for linac locking (RFOF: RF Over Fiber).
PV Name | Record Type | DESC | Functionality |
---|---|---|---|
$(PREFIX):COMMAND | stringout | Record for sending ASCII commands | |
$(PREFIX):RESPONSE | lsi | ||
$(PREFIX):GET_VERS | stringin | Libera Sync 3 version | |
$(PREFIX):GET_TIME | stringin | Set Time | |
$(PREFIX):GET_TX_FAN_1 | ai | Tx fan 1 speed | |
$(PREFIX):GET_TX_FAN_2 | ai | Tx fan 2 speed | |
$(PREFIX):GET_TX_FAN_3 | ai | Tx fan 3 speed | |
$(PREFIX):GET_RX_FAN_1 | ai | Rx fan 1 speed | |
$(PREFIX):GET_RX_FAN_2 | ai | Rx fan 2 speed | |
$(PREFIX):GET_RX_FAN_3 | ai | Rx fan 3 speed | |
$(PREFIX):FAN_SPD_RBV | longin | Fan Speed setting | |
$(PREFIX):OPT_RBV | ai | Get optical link length | |
$(PREFIX):DELAY_RBV | ai | Get startup delay | |
$(PREFIX):FAN_SPD | longout | Set fan speed in rpm | |
$(PREFIX):OPT | ao | Set optical length in m | |
$(PREFIX):SET_POWER | bo | Start or Shutdown system | |
$(PREFIX):SET_DELAY | ao | Set startup delay | |
$(PREFIX):GET_DEV_STAT | longin | Output of device status command | |
$(PREFIX):UPTIME | longout | Device Uptime | |
$(PREFIX):LOCK_STATE | mbbo | Lock Notification State | |
$(PREFIX):STATE | mbbo | State Machine State | |
$(PREFIX):UNLOCKED | calc | ||
$(PREFIX):SEMI_LOCKED | calc | ||
$(PREFIX):LOCKED | calc | ||
$(PREFIX):START | calc | ||
$(PREFIX):SHUTDOWN | calc | ||
$(PREFIX):INIT | calc | ||
$(PREFIX):WARMING_UP | calc | ||
$(PREFIX):TUNING | calc | ||
$(PREFIX):READY | calc | ||
$(PREFIX):HEALTH | longout | Hex longout | |
$(PREFIX):HEALTH_MBBI | mbbiDirect | ||
$(PREFIX):ETH_CON_ERR | bi | Tx/Rx Eth connection failure | |
$(PREFIX):PWR_SUPPLY_V_ERR | bi | Power voltages are OOR | |
$(PREFIX):ENV_COND_ERR | bi | Environmental cond are OOR | |
$(PREFIX):INT_MOD_ERR | bi | Int Module's temps are OOR | |
$(PREFIX):RF_PWR_ERR | bi | RF Power is OOR | |
$(PREFIX):OPT_PWR_ERR | bi | Power sply voltages are OOR | |
$(PREFIX):LAS_PWR_ERR | bi | Laser is switched off | |
$(PREFIX):PHASE_ERR | bi | Phase loops not locked | |
$(PREFIX):FAN_SPD_ERR | bi | Fan revs are too low | |
$(PREFIX):PWR_SUPPLY_I_ERR | bi | Power Sply currents high | |
$(PREFIX):ERROR | longout | Hex longout | |
$(PREFIX):ERROR_MBBI | mbbiDirect | ||
$(PREFIX):ERROR_MBBI_2 | mbbiDirect | ||
$(PREFIX):TX_ETH_SYNC_ERR | bi | Eth synch lost | |
$(PREFIX):TX_RF_INPUT_ERR | bi | RF input OOR | |
$(PREFIX):TX_TEMP_SENS_ERR | bi | Temp sensors not working | |
$(PREFIX):TX_RF_IDN_ERR | bi | Tx: RF control id fail | |
$(PREFIX):TX_RF_SENS_ERR | bi | Tx: RF control sensor fail | |
$(PREFIX):TX_ARM_IDN_ERR | bi | Tx: Arm ctrl id failed | |
$(PREFIX):TX_ARM_SENS_ERR | bi | Tx: Arm ctrl sensor fail | |
$(PREFIX):RX_ETH_SYNC_ERR | bi | Eth synch lost | |
$(PREFIX):RX_RF_OUTPUT_ERR | bi | RF output OOR for 10 min | |
$(PREFIX):RX_TEMP_SENS_ERR | bi | Temp sensors not working | |
$(PREFIX):UNLOCK_ERR | bi | System unlocked for 15 min | |
$(PREFIX):RX_RF_IDN_ERR | bi | Rx: RF ctrl id fail | |
$(PREFIX):RX_RF_SENS_ERR | bi | Rx: RF ctrl sensor failure | |
$(PREFIX):RX_ARM_IDN_ERR | bi | Rx: Arm cntrl id failure | |
$(PREFIX):RX_ARM_SENS_ERR | bi | Rx: Arm ctrl sensor fail | |
$(PREFIX):SSTATE_RAW | longout | State Substate raw | |
$(PREFIX):SSTATE_CALC | calc | State Substate calc | |
$(PREFIX)::SSTATE_CALC_2 | calc | State Substate calc 2 | |
$(PREFIX):SSTATE_FANOUT | fanout | Substate fanout record | |
$(PREFIX):SSTATE_MBBO_1 | mbbo | Substate mbbo 1 | |
$(PREFIX):SSTATE_MBBO_2 | mbbo | Substate mbbo 2 | |
$(PREFIX):SSTATE_MBBO_3 | mbbo | Substate mbbo 3 | |
$(PREFIX):SSTATE | stringout | Substate status stringout | |
$(PREFIX):TX_MY_IP | stringin | TX Unit IP | |
$(PREFIX):GET_TX_REM_ETH | stringin | TX Remote IP | |
$(PREFIX):SET_TX_REM_ETH | stringout | TX Remote IP | |
$(PREFIX):SCAN_TX | fanout | Scan Transmitter basic and advanced | |
$(PREFIX):GET_TX_BAS | aai | ||
$(PREFIX):GET_TX_ADV | aai | ||
$(PREFIX):TX_PC1 | ao | Tx Low drift optical link loop lock | |
$(PREFIX):TX_PC2 | ao | Laser and modulator loop lock (uV) | |
$(PREFIX):TX_PD1_I | ao | PD1 current - returned (uA) | |
$(PREFIX):TX_PD2_I | ao | PD2 current - transmitted (uA) | |
$(PREFIX):TX_LD_S | ao | Laser diode setpoint (uA) | |
$(PREFIX):TX_LAS_T | ao | Laser temperature (C) | |
$(PREFIX):TX_SPL_T | ao | Compensation spool temperature (C) | |
$(PREFIX):TX_SPL_S | ao | Compensation spool temp setpoint (C) | |
$(PREFIX):TX_RFIN | ao | Input RF Power (dBm) | |
$(PREFIX):TX_PD1_RF | ao | PD1 RF power - returned (dBm) | |
$(PREFIX):TX_PD2_RF | ao | PD2 RF power - transmitted (dBm) | |
$(PREFIX):TX_LAS_P | ao | Laser optical power (mW) | |
$(PREFIX):TX_RFO | ao | RF output power to MZM (dBm) | |
$(PREFIX):TX_LAS_I | ao | Laser current (mA) | |
$(PREFIX):TX_PS_V | ao | Electrical phase shifter voltage (V) | |
$(PREFIX):TX_ATTS_V | ao | RF attenuator setpoint voltage (V) | |
$(PREFIX):TX_ATT_V | ao | RF attenuator voltage (V) | |
$(PREFIX):TX_PSI_V | ao | Input phase shifter voltage (V) | |
$(PREFIX):TX_MZM_V | ao | MZ modulator bias voltage (V) | |
$(PREFIX):TX_VOA_S | ao | VOA controller setpoint (mA) | |
$(PREFIX):TX_VOA_V | ao | VOA voltage (V) | |
$(PREFIX):TX_STP_T | ao | Temp setpoint for internal modules (C) | |
$(PREFIX):TX_T | ao | TX board temperature (C) | |
$(PREFIX):TX_OPT_T | ao | Optical assembly temperature (C) | |
$(PREFIX):TX_EXT_H | ao | External relative humidity (%) | |
$(PREFIX):TX_EXTH_T | ao | External temp (humidity sensor) (C) | |
$(PREFIX):TX_EXT_P | ao | External pressure (mbar) | |
$(PREFIX):TX_EXTP_T | ao | External temp (pressure sensor) (C) | |
$(PREFIX):TX_INT_H | ao | Internal relative humidity (%) | |
$(PREFIX):TX_INTH_T | ao | Internal temp (humidity sensor) (C) | |
$(PREFIX):TX_INT_P | ao | Internal pressure (mbar) | |
$(PREFIX):TX_INTP_T | ao | Internal temp (pressure sensor) (C) | |
$(PREFIX):RX_MY_IP | stringin | RX Unit IP | |
$(PREFIX):GET_RX_REM_ETH | stringin | RX Remote IP | |
$(PREFIX):SET_RX_REM_ETH | stringout | RX Remote IP | |
$(PREFIX):SCAN_RX | fanout | Scan receiver basic and advanced | |
$(PREFIX):GET_RX_BAS | aai | ||
$(PREFIX):GET_RX_ADV | aai | ||
$(PREFIX):RX_PC1 | ao | RX internal lock | |
$(PREFIX):RX_PD1_I | ao | Compensated link photodiode current | |
$(PREFIX):RX_PD2_I | ao | Low-noise link photodiode current | |
$(PREFIX):RX_RFOUT | ao | Output RF power | |
$(PREFIX):RX_PD1_RF | ao | Compensated link photodiode power | |
$(PREFIX):RX_PD2_RF | ao | Low-noise link photodiode RF power | |
$(PREFIX):RX_ORF_S | ao | Output RF power setpoint | |
$(PREFIX):RX_ATT_V | ao | Variable attenuator voltage | |
$(PREFIX):RX_PS_V | ao | Phase shifter voltage | |
$(PREFIX):RX_STP_T | ao | Module temperature setpoint | |
$(PREFIX):RX_T | ao | Rx board temperature | |
$(PREFIX):RX_OPT_T | ao | Optical assembly temperature | |
$(PREFIX):RX_SPL_T | ao | Rx spool temperature | |
$(PREFIX):RX_EXT_H | ao | External relative humidity | |
$(PREFIX):RX_EXTH_T | ao | External temp (humidity sensor) | |
$(PREFIX):RX_EXT_P | ao | External pressure (mbar) | |
$(PREFIX):RX_EXTP_T | ao | External temp (pressure sensor) | |
$(PREFIX):RX_INT_H | ao | Internal relative humidity | |
$(PREFIX):RX_INTH_T | ao | Internal temp (humidity sensor) | |
$(PREFIX):RX_INT_P | ao | Internal pressure (mbar) | |
$(PREFIX):RX_INTP_T | ao | Internal temp (pressure sensor) |