laser diagram from Bill Pellico:

Image Added

Minutes

• We have a box enclosure
  • Pietro and Sander need to look into key, led control and interlock
•  Students:
  • We have a SULI Electrical Engineering undergrad coming during the summer (Jack)
  • We have a Physics grad student from Michigan
• Pietro presented the laser driver reverse engineered PCB
  • the test needs to continue

Minutes

• Students:
  • We have a SULI Electrical Engineering undergrad (Around June - August '24)
  • We have to look for a Physics grad student
• Discussion about the 80/20 cutting
• Marty found a nice ppt from TIPP2023 about a group that used our same laser
• We will buy also another "naked laser" without driver and ask for Bill Pellico about his design
• We will go for a very simple OPC Board design, as simple as possible

Business of the day:
Zoom: https://stanford.zoom.us/j/6723568666?pwd=eGxoSEs0ODc2UDdjL0NWR3RNSUZ3dz09
after discussing with Alex, my suggestion for the agenda is:
1. Thanking Alex for his work!, discussing new PI role, discussing what we need for the smoothest transition
2. Information gained from talk to Bill Pellico from Fermilab
3. Information gained from attending POF Fermilab meeting (David Martinez Caicedo)
4. Updated idea on cryogenic setup (reusing open LN2 duwar)
5. Discuss proposal for redistribution of hours
6. Discuss possible summer student opportunities: SULI UG, Stanford UG, direct hire from University grad, GEM fellow grad
7. Quick prep for safety meeting this afternoon
8. Any other updates/business? (edited) 

-drawings received from Dune on their laser enclosure box and feedthrough clamshell design.

-Example quote received for laser enclosure material  (walls and 8020) 

Minutes

• a new small testing TPC is being constructed by James for the DUNE project with delivery for June. This is a light-tight open dewer. This can be used as our cryogenic setup.
• Possible summer students, probably a good number would be 2 grad students, one physics and one engineering   
  • There is a promising MSU grad student through James
• Should we change vendor for the laser? let's create a set of questions for Bill Pellico
• drawings received from Dune on their laser enclosure box and feedthrough clamshell design.

• Sander is progressing on the safety procedures. He had some technical questions that were answered by the group.
• Marty has some technical questions regarding the diode. Alex should check the MAPS excel sheet and propose a technical meeting with Marty.
• Pietro made a first design for the PCB. The group made the following suggestions:
  • The diode should be off the board, inside the sealed box. We could have a connecter that allows us to easily connect/disconnect the diode

  • We should foresee a power pulsing scheme with a MHz range. More precisely: the load consumes most of the stored power within 1 us, with a 120 Hz repetition frequency. To be foreseen: power storage capacitor, switches controlled at 1MHz, and deal with the case where the average input power is not equal to the average consumed power.

  • Provide probing pins for easy monitoring on oscilloscope

  • Think about the case where the diode would operate on a floating ground for TPC operation (not necessarily implemented in this iteration)

  • Provide key, interlock, light diode (green/red) for the sealed box

• We need to design the 80/20 box (James would sketch one?)

• Alex showed the initial Smartsheet planning, which was modified according to the group's suggestions. Objective: Have a first laser by April 1st, with Safety Ok, and PCB ready. For a more detailed planning please visit the Smartsheet page:

Meeting Minutes: 

 We had our first laser safety meeting with Mike Woods and these slides were presented: 231130 first laser safety meeting.pptx

• • We should look at commercial products to see how they are doing interlocks
  • Important things that our system should have:
    • Key
    • Emission Indicator (red/green)
    • interlocking
    • (optional) Emergency OFF button
  • The box should have 2 redundant interlocks in series
  • If the box is made up to specs we will not need a separate laser area and will not need eye protection to operate
  • Box material can be 80/20 Aluminum
  • For the feedthrough we should think of having an elbow to avoid direct line of sight
  • We have to take into account the fiber bend radius
  • SOP is not enough, we will need a separate approval to operate
  • People working on the assembly of this will need:
    • 253
    • 131
    • T53
  • People only operating will need only a simpler laser safety basic course
    • ???
  • Mike gave us permission to buy the laser

Next Steps: 

• • Mike Woods asked for a component list
  • Norman Picker asked us to start a Hazard list with Mitigation (All the risks will be Extremely low)