Search/Navigation:
Related:
SLAC/EPP
/HPS Public
Jefferson Lab/Hall B
/HPS Run Wiki
S30XL-LESA/LDMX
...
Collimator scattering at JLab - link
Pre-NLCTA beam test slides from Pelle - link
Summary of results from beam test from Pelle - link
Sensor probing results in lab - link
Calibration and lab tests after pulling wirebonds from Omar - link
10pC:
100pC:
Beam spot for one of them as example:
...
...
/u1/software/daq/baseline_XpC_YF_ZV_HHMM.bin
...
Calibration:
180V bias: /u1/data/SVT2014/half_module/gimp_lab_postnlcta/1/
220V bias: /u1/data/SVT2014/half_module/gimp_lab_postnlcta/2/
We observed that there was a new channel that had high noise after installation. It was not there during test with the source. Could be dust or a real pin hole
...
10:37
Move in foils one by one and observe beam spot on phosphor screen. Picture and extracted spot size at each thickness can be seen below. The screen is about 75cm downstream of the exit window.
# foils | Tiff | FWHM |
---|---|---|
0 |
| |
1 |
| |
2 |
| |
3 |
| |
4 |
| |
5 |
| |
6 |
| |
7 |
|
We should check if we can extract the beam spot size on the Be window from this data and ask Mike if it's consistent with his experience.
10:49
Lower bunch charge.
Insert 6 foils.
Still possible to see the beam on the phosphor screen but barely.
Mike estimates this to be order of 1fC/bunch.
...
Runs taken, all at 6 foils:
Time | Bunch charge (pC) | ADC1 | Bias (V) | Ileak (uA) | Baseline | Baseline 180V | Comment | |||
---|---|---|---|---|---|---|---|---|---|---|
~11:00 | ?~0.001 | - | 180 | 10 | links | links |
| |||
11:36 | 1.0 | 0.002 | 180 | 17 |
|
| ||||
|
| 1.0 | 0.002 | 250 | 22 |
|
| |||
|
| 1.0 | 0.002 | 350 | 22 |
|
|
| ||
| 1 | 0.002 | 400 | 38 |
|
|
| |||
| 1 | 0.002 | 500 | 21 |
|
|
| |||
12:00 | 10 | 0.01 | 180 | 6 |
|
| ||||
|
| 10 | 0.01 | 350 | 7 |
|
| |||
|
| 10 | 0.01 | 500 | 50 | |||||
|
|
|
| 100 | 0.135 | 180 | 7 | |||
|
|
|
| 100 | 0.135 | 250 | 6 | |||
|
|
|
| 100 | 0.135 | 350 | 14 |
|
|
|
11:36
Everything looks ok for 1pC setting.
Baseline taken at 180V, after irradiating with 1 pC at 180V:
Baseline taken at 250V, after irradiating with 1 pC at 250V:
Baseline taken at 180V, after irradiating with 1 pC at 250V:
Baseline taken at 350V, after irradiating with 1 pC at 350V:
Baseline taken at 180V, after irradiating with 1 pC at 350V:
Baseline taken at 400V, after irradiating with 1 pC at 400V:
Baseline taken at 180V, after irradiating with 1 pC at 400V:
Baseline taken at 450V, after irradiating with 1 pC at 450V:
Baseline taken at 180V, after irradiating with 1 pC at 450V:
Baseline taken at 500V, after irradiating with 1 pC at 500V:
Baseline taken at 180V, after irradiating with 1 pC at 500V:
12:00
At 10pC and 500V we observed a channel with x3 higher noise in the "weird" apv chip which looked like a pinhole candidate. However, after cycling the bias it went awayit seem to go away with lower bias voltage.
We observe a previously unseen step in the noise from 30 to 35 ADC in the middle of both working APV25. This step was turning on over a couple of channels. Not sure what this is.
Baseline taken at 180V, after irradiating with 10 pC at 180V:
Baseline taken at 350V, after irradiating with 10 pC at 350V:
Baseline taken at 180V, after irradiating with 10 pC at 350V:
Baseline taken at 500V, after irradiating with 10 pC at 500V:
Baseline taken at 180V, after irradiating with 10 pC at 500V:
...
Since we'd like to keep some channels alive we stop at this point.
Baseline taken at 180V, after irradiating with 100 pC at 180V:
Baseline taken at 250V, after irradiating with 100 pC at 250V:
Baseline taken at 180V, after irradiating with 100 pC at 250V:
Baseline taken at 350V, after irradiating with 100 pC at 350V:
Baseline taken at 180V, after irradiating with 100 pC at 350V:
Baseline taken at 180V in group C:
IP address: 172.27.244.72
...
Manual
Serial: 9600 8N1unmigrated-wiki-markup
Common commands:
"measure?" - returns \ [voltage, current, \ ]
"source:voltage?" - returns voltage
"source:voltage 10" - set to 10 V
"output on" - output on
"output?" - returns 1 for on, 0 for off
"source:voltage:range up/down" - change range for voltage setting
Manual
Serial:
Common commands:
"SOUT000" - enable output
"SOUT001" - disable output
"VOLT00XY.Z" - sets voltage to XY.Z Volts
...