28 October 2022:
- All detectors in this table are operational.
- YAG cameras verified:
- YAG0
- YAG1
- YAG3
- YAG4 (new, by Zyla)
20 October 2022: Zyla update.
- The camera was completely disconnected.
- All connections remade except for the other end of the DB15 cable (power...)
- Will look for this during housekeeping, searched multiple areas inn the hutch today.
19 October 2022: Resurvey status.
- Xray_imaging and SPL_TC_alignment gigEs operating.
- Verified operation of YAG1 and the SPL/Compressor gigEs (CompInNF/FF, CompOutNF/FF) not listed here.
- All 4 Opals and the ePix100a at XTCS are running.
- The Zyla is not appearing in the DAQ, will reset today.
The detector locations within the target chamber are marked on this diagram:
Detector Number | Type | Function | In DAQ? | Notes | Cabled? | Running? | Comments | |||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | ePix100a | single photon diagnostics | Yes | in-vac | Yes | etch 12; vertical holder Q0 fibers/PDU
Not usable at these intensities (>1019 ?) | ||||||
2 | ePix100a | XTCSsingle photon diagnostics | Yes | in-vac | Yes | Yes | etch 25; horizontal holder Q1 fibers/PDUePix 1. | |||||
3 | Yes | in-vac | 4 | opal 2K | e- spectrometerNo | Yes | in-air | Yes | Yes | opal4_electron_spectrometer | ||
Not used for L-10008. | ||||||||||||
6 | opal 2K | NF/FF | Yes | in-air | Yes | Yes | opal1_nf_ff Replaced 1K with 2K. | |||||
7 | opal 4K | Imaging spot | Yes | in-air | Yes | Yes | opal2_focus_img | |||||
8 | opal 4K | Time Tool | Yes | in-air | Yes | Yes | opal7_timetool | |||||
ePix0 Q2 fibers/PDU Recovering from water spill. | ||||||||||||
4 | ePix100a | Kalpha User spectrometer | Yes | in-vac | Yes | Yes | Q3 fibers/PDU | |||||
59 | Zyla | MXI | Yes | in-air | Yes | Yes | zyla_xray_east Restart procedure at Zyla and iStar confluence page. Host is daq-mec-cam02. | |||||
106 | gigE POE | replacement for GIGE4 | XTCAV | YesNo | in-air, using old GIGE-MEC-CAM08 (Mako G-032B POE)vac | Yes | Yes | Now known as the beamline camera "XRay_Imaging" | ||||
11 | gigE POE | SPL_TC_alignment | No | in-air, using old GIGE-MEC-CAM07 (Mako G-032B POE) | Yes | Yes | It does run well. From time to time, it 'freezes' such that we have to start/stop again. Nothing serious. The camera works well for its purpose! | 13 |
|
| ||
ePix100a SPC vertical → Q0 fiber & PDU S0
ePix100a SPC horizontal → Q1 fiber & PDU S1
ePix100a XRTS → Q2 fiber & PDU S2
ePix100a Kalpha → Q3 fiber & PDU S3
Update on Fiber Mapping: (see 7.11 Opal Camera Configuration for fiber patch panel information)
- Commenting out epix100a_2_XRTS and setting "-i 2" for epix100a_3_Kalpha worked (but keeping -P 0x40) worked, and I checked via image inspection that I saw two different detectors.
- The epix100a persisted all day across nearly complete fiber changes - so the DAQ config is the issue (and the IOC was ok).
- In detail: Dimitri and I got into the fiber routing behind the Quad connections in PR60 since we suspect cable problems coming into cam01. So now cam01 has both the direct fiber bundle and the Fiberstore QSFP-SR4-40G that was in one of the two pgp02 ports. We don't need the quads again until late Feb, so can sort this out post L10011.