...
- Default
...
- "accelerator"
...
- is
...
- loaded
...
- at
...
- startup.
...
If
...
- you
...
- want
...
- to
...
- load
...
- a
...
- test
...
- model,
...
- Use
...
- Accelerator->Load
...
- Accelerator...
...
- Accelerator->Sequences
...
- is
...
- in
...
- fact
...
- really
...
- for
...
- automatic
...
- calculation
...
- of
...
- bump
...
- knobs
...
- to
...
- create
...
- a
...
- knob,
...
- just
...
- do
...
- the
...
- following:
...
- Optionally,
...
- create
...
- a
...
- group
...
-
.
- Create a knob
- Add devices:
- Do this "by hand" if you know the PV. Eg YCOR:IN20:492:BDES
-
...
- Do this by "drilldown"
...
- (which
...
- uses
...
- physics
...
- name).
...
- In
...
- the
...
- Editor:
...
- Select
...
- a
...
- model
...
- sequence:
...
- Eg
...
- BXG
...
- TO
...
- BX01.
...
- Note
...
- that
...
- sequences
...
- are
...
- in
...
- alphabetical
...
- order.
...
- That
...
- is
...
- on
...
- the
...
- fix
...
- list.
...
- Select
...
- a
...
- device
...
- "type".
...
- Note
...
- that
...
- the
...
- type
...
- names
...
- given
...
- are:
...
1)
...
- SNS
...
- type
...
- names,
...
- which
...
- themselves
...
- use
...
- >1
...
- name
...
- eg
...
- hcorr
...
- ==
...
- dch
...
- ==
...
- horrzcorr
...
- =>
...
- X
...
- correctors.
...
2)
...
- and
...
- also
...
- flattened
...
- hierarchy
...
- of
...
- types,
...
- eg
...
- type
...
- "dipole"
...
- includes
...
- hcorr
...
- and
...
- vcorr.
...
- Select
...
- a
...
- device
...
- name,
...
- by
...
- "physics
...
- name".
...
- Select
...
- FieldSet
...
- (not
...
- FieldRB).
...
- (issue:
...
- FieldRB
...
- should
...
- not
...
- be
...
- offered).
...
- Or calculate bump knobs
- Select a section of contiguous sequence of sections (a "combo sequence") Accelerator->Sequences
BXG TO BX01 - BX01 to BX02 works. - Knobs->(Make Horizontal Bumps | Make vertical bumps) Make Horizontal Bumps (Make Vertical Doesn't work, since it seems so many of our correctors are SLC!)
- For Horizontal Bumps: These setups were tested.
- Design Offset 3 (default) magnets - works (4 magnet doesn't work!)
- Design Angle 5 (default) magnets - works
- Live Offset 3 - works
- Live Angle 5 works - works
- For Vertical Bumps, select sections BXG to BX01 - QM15 to FV2
- Design Offset 3 (default) magnets - works, but they're mostly SLC magnets.
- Select a section of contiguous sequence of sections (a "combo sequence") Accelerator->Sequences