LAT00x - LAT Power On Sequence Test [101000058]

LatPowerOn LAT00x - LAT Power On Sequence Test

Tue Mar 28 20:01:31 2006

Hardware Configuration

SIU Cross Strapping: AA

DAQ Cross Strapping: AA

DAQ Feed: Primary

SIU: Primary

GASU: Primary

EPU-A: 0

EPU-B: 1

ACD HVBS: 1

PDU: Redundant

Test Summary

Configuration file: tbLatPowerOn.cfg

Configuration file version: 1.15

Configuration file release: L00-12-00

Run Id: 101000058

Run Report: 101000058_rcReport.xml

Start Up Step	Prerequisite	Verification
Primary SIU boot	PASSED	PASSED
Secondary SIU boot	PASSED	PASSED
Dwell On SIU	PASSED	PASSED
Enable DAQ Feed	PASSED	PASSED
Power On PDU	PASSED	PASSED
SIU Control of TCS	DISABLED	DISABLED
Power On EPU 0	PASSED	PASSED
Secondary boot of EPU 0	PASSED	PASSED
Power On EPU 1	PASSED	PASSED
Secondary boot of EPU 1	PASSED	PASSED
Power On TEM 0	PASSED	PASSED
Power On TEM 0 CAL	PASSED	PASSED
Power On TEM 0 TKR	PASSED	PASSED
Power On ACD free board 0	PASSED	PASSED
Issue 3 Erroneous Commands	PASSED	PASSED

Total time to power on all towers: 73 seconds

Average tower power on time: 73 seconds

Total time to power on all free boards: 23 seconds

Average free board power on time: 23 seconds

Completion Status: PASSED

Primary SIU boot

Prerequisite:

readSiuCurrent: Read the SIU feed current as -0.01A

siuFeedVoltage: SIU 1 feed voltage 0.78V is within [-1.0, 1.0]

siuTemp: SIU 1 temperature 30.24C is within [-30.0, 45.0]

Verification:

siuFeedVoltage: SIU 1 feed voltage 28.12V is within [27.0, 29.0]

siuCurrentDelta: SIU 1 feed current delta 0.31A is within [-1.0, 1.0]

siuVoltage: SIU 1 3.3/5V voltage 2.33V is within [0.0, 6.0]

siuMemCheck: SIU 1 Memory Check passed.

siuCommCheck: SIU 1 Comm Check passed.

siuBootTlm: SIU boot telemetry received.

siuTemp: SIU 1 temperature 30.16C is within [-30.0, 45.0]

Secondary SIU boot

Prerequisite:

siuVoltage: SIU 1 3.3/5V voltage 2.40V is within [0.0, 6.0]

siuMemCheck: SIU 1 Memory Check passed.

siuCommCheck: SIU 1 Comm Check passed.

siuBootTlm: SIU boot telemetry received.

siuTemp: SIU 1 temperature 30.24C is within [-30.0, 45.0]

siuTemp: Sending secondary boot command to SIU 1 using flags hi=0x5400, lo=0xc000 ...

Verification:

latHskTlm: LAT housekeeping telemetry received.

siuTemp: SIU 1 temperature 30.24C is within [-30.0, 45.0]

Dwell On SIU

Prerequisite:

Verification:

siuCurrentDelta: Checking if dwell telemetry is in range [-1.000, 1.000] for payload VSC_RBPU_SIU_C, values [0.23, 0.27, 0.23, 0.25, 0.23] (starting with index:0, margin:0)

siuCurrentDelta: Dwell telemetry for payload VSC_RBPU_SIU_C are within [-1.000, 1.000]

siuVoltage: Checking if dwell telemetry is in range [0.000, 6.000] for payload L_DAQ_P_SIU_V, values [2.34, 2.36, 2.34, 2.34, 2.34] (starting with index:0, margin:0)

siuVoltage: Dwell telemetry for payload L_DAQ_P_SIU_V are within [0.000, 6.000]

siuTemp: Checking if dwell telemetry is in range [-30.000, 45.000] for payload L_DAQ_P_SIU_T, values [29.67, 30.24, 29.59, 29.59, 29.26] (starting with index:0, margin:0)

siuTemp: Dwell telemetry for payload L_DAQ_P_SIU_T are within [-30.000, 45.000]

siuFeedVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_SIU_V, values [28.08, 27.93, 28.32, 28.27, 28.22] (starting with index:0, margin:0)

siuFeedVoltage: Dwell telemetry for payload VSC_RBPU_SIU_V are within [27.000, 29.000]

siuCpuJTemp: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPUJTEMP, values [35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00] (starting with index:0, margin:0)

siuCpuJTemp: Dwell telemetry for payload LHKSIUCPUJTEMP are within [1.000, 999.000]

siuCpuLdMin: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPULDMIN, values [1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:0, margin:0)

siuCpuLdMin: Dwell telemetry for payload LHKSIUCPULDMIN are within [1.000, 999.000]

siuCpuAvLdm: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPUAVLDM, values [4.00, 4.00, 4.00, 4.00, 4.00, 4.00, 4.00, 3.00, 3.00, 3.00, 3.00] (starting with index:0, margin:0)

siuCpuAvLdm: Dwell telemetry for payload LHKSIUCPUAVLDM are within [1.000, 999.000]

siuCpuAvLds: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPUAVLDS, values [1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:0, margin:0)

siuCpuAvLds: Dwell telemetry for payload LHKSIUCPUAVLDS are within [1.000, 999.000]

siuCpuLdMax: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPULDMAX, values [10.00, 10.00, 10.00, 10.00, 10.00, 10.00, 10.00, 10.00, 10.00, 10.00, 10.00] (starting with index:0, margin:0)

siuCpuLdMax: Dwell telemetry for payload LHKSIUCPULDMAX are within [1.000, 999.000]

readDaqFeedCurrent: Read the DAQ feed current as -0.10A

Enable DAQ Feed

Prerequisite:

readDaqFeedCurrent: Read the DAQ feed current as 0.34A

daqFeedVoltage: DAQ feed voltage 0.20V is within [-1.0, 1.0]

pduTemp: PDU temperature 23.20C is within [-30.0, 45.0]

Verification:

daqFeedVoltage: DAQ feed voltage 28.08V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta -0.39A is within [-2.0, 2.0]

pduTemp: PDU temperature 23.74C is within [-30.0, 45.0]

pduVoltage: PDU 1 3.3Vvoltage 0.01V is within [-0.10000000000000001, 0.10000000000000001]

readDaqFeedCurrent: Read the DAQ feed current as -0.05A

Power On PDU

Prerequisite:

daqFeedVoltage: DAQ feed voltage 28.12V is within [27.0, 29.0]

pduTemp: PDU temperature 23.74C is within [-30.0, 45.0]

gasuTemp: GASU temperature 23.40C is within [-30.0, 45.0]

gasu33V: Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_EBM33V, values [1.01, 3.30, 3.35, 3.36, 3.32] (starting with index:2, margin:0)

gasu33V: Dwell telemetry for payload L_DAQ_P_EBM33V are within [3.000, 3.600]

daqFeedVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_DAQ_V, values [28.12, 28.08, 28.27, 28.27, 28.08] (starting with index:2, margin:0)

daqFeedVoltage: Dwell telemetry for payload VSC_RBPU_DAQ_V are within [27.000, 29.000]

gasuTemp: Checking if dwell telemetry is in range [-30.000, 45.000] for payload L_DAQ_P_GASU_T, values [23.95, 23.13, 23.20, 23.74, 23.74] (starting with index:2, margin:0)

gasuTemp: Dwell telemetry for payload L_DAQ_P_GASU_T are within [-30.000, 45.000]

pduTemp: Checking if dwell telemetry is in range [-30.000, 45.000] for payload L_DAQ_R_PDU_T, values [23.67, 24.01, 23.74, 23.81, 23.13] (starting with index:2, margin:0)

pduTemp: Dwell telemetry for payload L_DAQ_R_PDU_T are within [-30.000, 45.000]

pduVoltage: Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_R_PDU_V, values [0.02, 3.40, 3.36, 3.35, 3.36] (starting with index:2, margin:0)

pduVoltage: Dwell telemetry for payload L_DAQ_R_PDU_V are within [3.000, 3.600]

gasu25V: Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_EBM25V, values [-0.00, 2.47, 2.43, 2.47, 2.46] (starting with index:2, margin:0)

gasu25V: Dwell telemetry for payload L_DAQ_P_EBM25V are within [2.000, 2.600]

gasu25V: Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_GEM25V, values [0.01, 2.46, 2.49, 2.43, 2.46] (starting with index:2, margin:0)

gasu25V: Dwell telemetry for payload L_DAQ_P_GEM25V are within [2.000, 2.600]

gasu33V: Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_GEM33V, values [1.01, 3.35, 3.32, 3.32, 3.33] (starting with index:2, margin:0)

gasu33V: Dwell telemetry for payload L_DAQ_P_GEM33V are within [3.000, 3.600]

daqCurrentDelta: Checking if dwell telemetry is in range [-2.000, 2.000] for payload VSC_RBPU_DAQ_C, values [0.10, 0.44, 0.59, 0.10, 0.29] (starting with index:2, margin:0)

daqCurrentDelta: Dwell telemetry for payload VSC_RBPU_DAQ_C are within [-2.000, 2.000]

Verification:

daqFeedVoltage: DAQ feed voltage 28.08V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.78A is within [-2.0, 2.0]

pduTemp: PDU temperature 23.74C is within [-30.0, 45.0]

pduVoltage: PDU 1 3.3Vvoltage 3.39V is within [3.0, 3.6000000000000001]

gasuTemp: GASU temperature 24.01C is within [-30.0, 45.0]

gasuVoltages: AEM/EBM 3.3V voltage 3.27V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.43V is within [2.0, 2.6000000000000001]

gasuVoltages: CRU/GEM 3.3V voltage 3.32V is within [3.0, 3.6000000000000001]

gasuVoltages: CRU/GEM 2.5V voltage 2.44V is within [2.0, 2.6000000000000001]

readDaqFeedCurrent: Read the DAQ feed current as 0.34A

Power On EPU 0

Prerequisite:

daqFeedVoltage: DAQ feed voltage 28.17V is within [27.0, 29.0]

epuTemp: PDU 1 EPU 0 temperature measured as 24.15C and within the required range of [-30.0, 45.0]

epuPwrMgt: Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP1EPU0PM, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:9, margin:5)

epuPwrMgt: Dwell telemetry for payload LHKP1EPU0PM are within [1.000, 1.000]

epuCnvt: Checking if dwell telemetry is in range [0.000, 0.000] for payload LHKP1EPU0CNVT, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00] (starting with index:9, margin:5)

epuCnvt: Dwell telemetry for payload LHKP1EPU0CNVT are within [0.000, 0.000]

epuTemp: Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP1EPU0T, values [24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15, 24.15] (starting with index:9, margin:5)

epuTemp: Dwell telemetry for payload LHKP1EPU0T are within [-30.000, 45.000]

Verification:

daqFeedVoltage: DAQ feed voltage 28.08V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.49A is within [-2.0, 2.0]

epuVoltage: PDU 1 EPU 0 3.3V voltage measured as 2.24V and within the required range of [2.0, 3.5]

epuBootTlm: EPU 0 boot telemetry received.

epuTemp: PDU 1 EPU 0 temperature measured as 24.44C and within the required range of [-30.0, 45.0]

readDaqFeedCurrent: Read the DAQ feed current as 1.17A

Secondary boot of EPU 0

Prerequisite:

epuVoltage: PDU 1 EPU 0 3.3V voltage measured as 2.24V and within the required range of [2.0, 3.5]

epuTemp: PDU 1 EPU 0 temperature measured as 24.57C and within the required range of [-30.0, 45.0]

epuTemp: Sending secondary boot command to EPU 0 using flags hi=0x5400, lo=0xc000 ...

Verification:

epuHskTlm: EPU 0 CPU junction temperature measured as 47 and within the required range of [1, 999]

epuTemp: PDU 1 EPU 0 temperature measured as 24.96C and within the required range of [-30.0, 45.0]

Power On EPU 1

Prerequisite:

daqFeedVoltage: DAQ feed voltage 28.12V is within [27.0, 29.0]

epuTemp: PDU 1 EPU 1 temperature measured as 23.56C and within the required range of [-30.0, 45.0]

epuPwrMgt: Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP1EPU1PM, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:9, margin:5)

epuPwrMgt: Dwell telemetry for payload LHKP1EPU1PM are within [1.000, 1.000]

epuTemp: Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP1EPU1T, values [23.59, 23.59, 23.59, 23.59, 23.59, 23.59, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56, 23.56] (starting with index:9, margin:5)

epuTemp: Dwell telemetry for payload LHKP1EPU1T are within [-30.000, 45.000]

epuCnvt: Checking if dwell telemetry is in range [0.000, 0.000] for payload LHKP1EPU1CNVT, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00] (starting with index:9, margin:5)

epuCnvt: Dwell telemetry for payload LHKP1EPU1CNVT are within [0.000, 0.000]

Verification:

daqFeedVoltage: DAQ feed voltage 28.12V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.00A is within [-2.0, 2.0]

epuVoltage: PDU 1 EPU 1 3.3V voltage measured as 2.26V and within the required range of [2.0, 3.5]

epuBootTlm: EPU 1 boot telemetry received.

epuTemp: PDU 1 EPU 1 temperature measured as 23.88C and within the required range of [-30.0, 45.0]

readDaqFeedCurrent: Read the DAQ feed current as 1.71A

Secondary boot of EPU 1

Prerequisite:

epuVoltage: PDU 1 EPU 1 3.3V voltage measured as 2.26V and within the required range of [2.0, 3.5]

epuTemp: PDU 1 EPU 1 temperature measured as 23.98C and within the required range of [-30.0, 45.0]

epuTemp: Sending secondary boot command to EPU 1 using flags hi=0x5400, lo=0xc000 ...

Verification:

epuHskTlm: EPU 1 CPU junction temperature measured as 43 and within the required range of [1, 999]

epuTemp: PDU 1 EPU 1 temperature measured as 24.36C and within the required range of [-30.0, 45.0]

Power On TEM 0

Prerequisite:

daqFeedVoltage: DAQ feed voltage 28.08V is within [27.0, 29.0]

temDaqTemp: PDU 1 TEM 0 DAQ board temperature measured as 23.64C and within the required range of [-30.0, 45.0]

temPsTemp: PDU 1 TEM 0 power supply temperature measured as 23.45C and within the required range of [-30.0, 45.0]

temVoltage: Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0TEM33V, values [0.20, 0.20, 0.20, 0.20, 0.20, 0.20, 0.20, 0.20, 0.20, 3.41, 3.41, 3.41, 3.41, 3.41, 3.41, 3.41, 3.41, 3.41, 3.40, 3.40] (starting with index:9, margin:7)

temVoltage: Dwell telemetry for payload LHKT0TEM33V are within [3.000, 3.500]

temPsVoltage: Checking if dwell telemetry is in range [25.500, 29.000] for payload LHKT0TEM28V0, values [33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 28.06, 28.06, 28.06, 28.06, 28.06, 28.06, 28.06, 28.06, 28.06, 28.06, 28.06] (starting with index:9, margin:7)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V0 are within [25.500, 29.000]

temPsVoltage: Checking if dwell telemetry is in range [25.500, 29.000] for payload LHKT0TEM28V1, values [13.69, 13.69, 13.69, 13.69, 13.69, 13.69, 13.69, 13.69, 13.69, 28.14, 28.14, 28.14, 28.14, 28.14, 28.14, 28.14, 28.14, 28.14, 28.13, 28.13] (starting with index:9, margin:7)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V1 are within [25.500, 29.000]

Verification:

daqFeedVoltage: DAQ feed voltage 28.27V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta -0.15A is within [-2.0, 2.0]

temPsCurrent: Warning: Conversion constant for LDET0TEM28I was not in the database, using the data from the configuration file

temPsCurrent: TEM 0 power supply current measured as -0.45A and within the required range of [-1.0, 5.0]

temVoltage: TEM 0 3.3V voltage measured as 3.40V and within the required range of [3.0, 3.5]

temDaqTemp: PDU 1 TEM 0 DAQ board temperature measured as 23.61C and within the required range of [-30.0, 45.0]

temPsTemp: PDU 1 TEM 0 power supply temperature measured as 23.45C and within the required range of [-30.0, 45.0]

readDaqFeedCurrent: Read the DAQ feed current as 1.56A

Power On TEM 0 CAL

Prerequisite:

temPsTemp: PDU 1 TEM 0 power supply temperature measured as 23.42C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 0 temperature 1 measured as 28.64C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 1 temperature 1 measured as 28.20C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 2 temperature 1 measured as 28.52C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 3 temperature 1 measured as 27.55C and within the required range of [-30.0, 45.0]

calBiasVoltage: Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV0, values [0.12, 0.12, 0.12, 0.12, 0.12, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25] (starting with index:9, margin:5)

calBiasVoltage: Dwell telemetry for payload LHKT0CALBSV0 are within [0.000, 80.000]

calBiasVoltage: Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV1, values [0.12, 0.12, 0.12, 0.12, 0.12, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65] (starting with index:9, margin:5)

calBiasVoltage: Dwell telemetry for payload LHKT0CALBSV1 are within [0.000, 80.000]

cal33VA: Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VA, values [0.00, 0.00, 0.00, 0.00, 0.00, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39] (starting with index:9, margin:5)

cal33VA: Dwell telemetry for payload LHKT0CAL33VA are within [3.000, 3.500]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V1, values [28.13, 28.13, 28.13, 28.13, 28.13, 28.01, 28.01, 28.01, 28.01, 28.01, 28.01, 28.01, 28.01, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V1 are within [27.000, 29.000]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V0, values [28.06, 28.06, 28.06, 28.06, 28.06, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V0 are within [27.000, 29.000]

cal33VD: Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VD, values [0.00, 0.00, 0.00, 0.00, 0.00, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36] (starting with index:9, margin:5)

cal33VD: Dwell telemetry for payload LHKT0CAL33VD are within [3.000, 3.500]

Verification:

daqFeedVoltage: DAQ feed voltage 27.78V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.39A is within [-2.0, 2.0]

temPsCurrent: Warning: Conversion constant for LDET0TEM28I was not in the database, using the data from the configuration file

temPsCurrent: TEM 0 power supply current measured as -0.17A and within the required range of [-1.0, 5.0]

cal33V: TEM 0 CAL 3.3V digital measured as 3.36V and within the required range of [3.0, 3.5]

cal33V: TEM 0 CAL 3.3V analog measured as 3.39V and within the required range of [3.0, 3.5]

calBias: TEM 0 CAL bias V0 measured as 0.25V and within the required range of [0.0, 80.0]

calBias: TEM 0 CAL bias V1 measured as 25.65V and within the required range of [0.0, 80.0]

calBias: Warning: Conversion constant for LDET0CALBIASI was not in the database, using the data from the configuration file

calBias: TEM 0 CAL bias current measured as 0.01A and within the required range of [-1.0, 6.0]

calAfeeTemp: TEM 0 CAL AFEE 0 temperature 1 measured as 28.64C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 1 temperature 1 measured as 28.16C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 2 temperature 1 measured as 28.56C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 3 temperature 1 measured as 27.59C and within the required range of [-30.0, 45.0]

readDaqFeedCurrent: Read the DAQ feed current as 1.90A

Power On TEM 0 TKR

Prerequisite:

temPsTemp: PDU 1 TEM 0 power supply temperature measured as 23.42C and within the required range of [-30.0, 45.0]

tkrTemp: TEM 0 TKR cable 0 temperature 0 measured as 27.91C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 0 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 1 temperature 0 measured as 28.05C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 1 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 2 temperature 0 measured as 27.45C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 2 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 3 temperature 0 measured as 29.49C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 3 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 4 temperature 0 measured as 27.91C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 4 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 5 temperature 0 measured as 29.00C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 5 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 6 temperature 0 measured as 27.20C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 6 temperature 1 measured as -108.07C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 7 temperature 0 measured as 27.84C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 7 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrBiasVoltage: Checking if dwell telemetry is in range [0.000, 105.000] for payload LHKT0TKRBV1, values [0.06, 0.06, 0.06, 0.06, 0.06, 25.90, 25.90, 25.90, 25.90, 25.90, 25.90, 25.90, 25.90, 25.77, 25.77, 25.77, 25.77, 25.77, 25.77, 25.77] (starting with index:9, margin:5)

tkrBiasVoltage: Dwell telemetry for payload LHKT0TKRBV1 are within [0.000, 105.000]

tkrBiasVoltage: Checking if dwell telemetry is in range [0.000, 105.000] for payload LHKT0TKRBV0, values [0.06, 0.06, 0.06, 0.06, 0.06, 0.37, 0.37, 0.37, 0.37, 0.37, 0.37, 0.37, 0.37, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31] (starting with index:9, margin:5)

tkrBiasVoltage: Dwell telemetry for payload LHKT0TKRBV0 are within [0.000, 105.000]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V1, values [28.02, 28.02, 28.02, 28.02, 28.02, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.78, 27.78, 27.78, 27.78, 27.78, 27.78, 27.78] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V1 are within [27.000, 29.000]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V0, values [27.89, 27.89, 27.89, 27.89, 27.89, 27.57, 27.57, 27.57, 27.57, 27.57, 27.57, 27.57, 27.57, 27.55, 27.55, 27.55, 27.55, 27.55, 27.55, 27.55] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V0 are within [27.000, 29.000]

tkr15VA: Checking if dwell telemetry is in range [0.000, 2.000] for payload LHKT0TKR15VAA, values [0.00, 0.00, 0.00, 0.00, 0.00, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44] (starting with index:9, margin:5)

tkr15VA: Dwell telemetry for payload LHKT0TKR15VAA are within [0.000, 2.000]

tkr25VA: Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VAB, values [0.00, 0.00, 0.00, 0.00, 0.00, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56, 2.56] (starting with index:9, margin:5)

tkr25VA: Dwell telemetry for payload LHKT0TKR25VAB are within [0.000, 3.000]

tkr25VD: Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VD, values [0.00, 0.00, 0.00, 0.00, 0.00, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53] (starting with index:9, margin:5)

tkr25VD: Dwell telemetry for payload LHKT0TKR25VD are within [0.000, 3.000]

Verification:

daqFeedVoltage: DAQ feed voltage 27.93V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.24A is within [-2.0, 2.0]

temPsCurrent: Warning: Conversion constant for LDET0TEM28I was not in the database, using the data from the configuration file

temPsCurrent: TEM 0 power supply current measured as 0.32A and within the required range of [-1.0, 5.0]

tkrVoltage: TEM 0 TKR 1.5V analog measured as 1.43V and within the required range of [0.0, 2.0]

tkrVoltage: TEM 0 TKR 2.5V digital measured as 2.53V and within the required range of [0.0, 3.0]

tkrVoltage: TEM 0 TKR 2.5V analog measured as 2.56V and within the required range of [0.0, 3.0]

tkrBias: TEM 0 TKR bias V0 measured as 0.31V and within the required range of [0.0, 105.0]

tkrBias: TEM 0 TKR bias V1 measured as 25.77V and within the required range of [0.0, 105.0]

tkrBias: Warning: Conversion constant for LDET0TKRBIASI was not in the database, using the data from the configuration file

tkrBias: TEM 0 TKR bias current measured as -0.00A and within the required range of [-1.0, 10.0]

tkrTemp: TEM 0 TKR cable 0 temperature 0 measured as 27.91C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 0 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 1 temperature 0 measured as 28.02C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 1 temperature 1 measured as -108.07C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 2 temperature 0 measured as 27.45C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 2 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 3 temperature 0 measured as 29.49C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 3 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 4 temperature 0 measured as 27.91C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 4 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 5 temperature 0 measured as 28.97C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 5 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 6 temperature 0 measured as 27.20C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 6 temperature 1 measured as -108.07C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 7 temperature 0 measured as 27.95C and within the required range of [-123.0, 45.0]

tkrTemp: TEM 0 TKR cable 7 temperature 1 measured as -114.72C and within the required range of [-123.0, 45.0]

readDaqFeedCurrent: Read the DAQ feed current as 2.49A

Power On ACD free board 0

Prerequisite:

gasuVoltages: AEM/EBM 3.3V voltage 3.32V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.42V is within [2.0, 2.6000000000000001]

gasuVoltages: Read the free board current as 0.00A

freeBoardTemp: Checking if dwell telemetry is in range [-15.000, 30.000] for payload LHKAEMFR0T, values [22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36, 22.36] (starting with index:20, margin:0)

freeBoardTemp: Dwell telemetry for payload LHKAEMFR0T are within [-15.000, 30.000]

freeBoardVoltage: Checking if dwell telemetry is in range [2.900, 3.800] for payload LHKAEMFR0VD, values [0.73, 0.73, 0.73, 0.73, 0.73, 0.73, 0.73, 3.43, 3.43, 3.43, 3.43, 3.43, 3.43, 3.43, 3.43, 3.55, 3.55, 3.55, 3.55, 3.55] (starting with index:20, margin:0)

freeBoardVoltage: Dwell telemetry for payload LHKAEMFR0VD are within [2.900, 3.800]

Verification:

gasuVoltages: AEM/EBM 3.3V voltage 3.35V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.42V is within [2.0, 2.6000000000000001]

freeBoardVoltage: AEM free board 0 voltage measured as 3.55V and within the required range of [2.8999999999999999, 3.7999999999999998]

freeBoardCurrentDelta: Free board current delta 0.00A is within [0.0, 0.90000000000000002]

freeBoardTemp: AEM free board 0 temperature measured as 22.36C and within the required range of [-15.0, 30.0]

Issue 3 Erroneous Commands

Prerequisite:

Verification:

badAPID: Bad APID test passed. The result was ('CTS_APIDNOQ', '"APID %d (0x%04x) does not map to an ITC queue"')

invalidPayload: Invalid payload test passed. The result was ('LHK_PRMERR', '"Invalid command parameter: %s %x"')

incompleteCmd: Incomplete command test passed. CVT timeout occurred and EPKTPARM message was observed.