LAT00x - LAT Power On Sequence Test [101000044]

 

 

 

 

 

 

 

LatPowerOn
LAT00x - LAT Power On Sequence Test

Mon Mar 6 18:15:31 2006

 

 

 

 

 

 

 

Test Summary

:  tbLatPowerOn.cfg

:  1.12

:  L00-09-00

:  101000044

:  online-v2r4p0_101000044_rcReport_rcReport.xml

Start Up Step Prerequisite Verification
Primary SIU boot PASSED PASSED
Secondary SIU boot PASSED PASSED
Dwell On SIU PASSED PASSED
Enable DAQ Feed PASSED PASSED
Power On PDU PASSED PASSED
SIU Control of TCS DISABLED DISABLED
Power On EPU 0 PASSED PASSED
Secondary boot of EPU 0 PASSED PASSED
Power On EPU 1 PASSED PASSED
Secondary boot of EPU 1 PASSED PASSED
Power On TEM 0 PASSED PASSED
Power On TEM 0 CAL PASSED PASSED
Power On TEM 0 TKR PASSED PASSED
Power On ACD free board 0 PASSED PASSED
Power On ACD free board 0 HVBS PASSED PASSED
Issue 3 Erroneous Commands PASSED PASSED
Ambient, Average and Peak Power Consumption PASSED PASSED

Total time to power on all towers: 70 seconds

Average tower power on time: 70 seconds

Total time to power on all free boards: 625 seconds

Average free board power on time: 625 seconds

:  PASSED

Primary SIU boot

: 

readSiuCurrent: Read the SIU feed current as -0.01A

siuFeedVoltage: SIU 1 feed voltage 0.73V is within [-1.0, 1.0]

siuTemp: SIU 1 temperature 27.78C is within [23.0, 50.0]

: 

siuFeedVoltage: SIU 1 feed voltage 28.12V is within [27.0, 29.0]

siuCurrentDelta: SIU 1 feed current delta 0.52A is within [-1.0, 1.0]

siuVoltage: SIU 1 3.3/5V voltage 2.34V is within [0.0, 6.0]

siuMemCheck: SIU 1 Memory Check passed.

siuCommCheck: SIU 1 Comm Check passed.

siuBootTlm: SIU boot telemetry received.

siuTemp: SIU 1 temperature 27.62C is within [23.0, 50.0]

Secondary SIU boot

: 

siuVoltage: SIU 1 3.3/5V voltage 2.33V is within [0.0, 6.0]

siuMemCheck: SIU 1 Memory Check passed.

siuCommCheck: SIU 1 Comm Check passed.

siuBootTlm: SIU boot telemetry received.

siuTemp: SIU 1 temperature 26.50C is within [23.0, 50.0]

siuTemp: Sending secondary boot command to SIU 1 using flags hi=0x5400, lo=0xc000 ...

: 

latHskTlm: LAT housekeeping telemetry received.

siuTemp: SIU 1 temperature 28.71C is within [23.0, 50.0]

Dwell On SIU

: 

: 

siuCurrentDelta: Checking if dwell telemetry is in range [-1.000, 1.000] for payload VSC_RBPU_SIU_C, values [0.17, 0.19, 0.19, 0.21, 0.18] (starting with index:0, margin:0)

siuCurrentDelta: Dwell telemetry for payload VSC_RBPU_SIU_C are within [-1.000, 1.000]

siuVoltage: Checking if dwell telemetry is in range [0.000, 6.000] for payload L_DAQ_P_SIU_V, values [2.38, 2.36, 2.38, 2.34, 2.35] (starting with index:0, margin:0)

siuVoltage: Dwell telemetry for payload L_DAQ_P_SIU_V are within [0.000, 6.000]

siuTemp: Checking if dwell telemetry is in range [23.000, 50.000] for payload L_DAQ_P_SIU_T, values [28.32, 28.71, 28.71, 28.01, 27.78] (starting with index:0, margin:0)

siuTemp: Dwell telemetry for payload L_DAQ_P_SIU_T are within [23.000, 50.000]

siuFeedVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_SIU_V, values [28.08, 27.73, 28.03, 28.17, 27.73] (starting with index:0, margin:0)

siuFeedVoltage: Dwell telemetry for payload VSC_RBPU_SIU_V are within [27.000, 29.000]

siuCpuJTemp: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPUJTEMP, values [35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00, 35.00] (starting with index:0, margin:0)

siuCpuJTemp: Dwell telemetry for payload LHKSIUCPUJTEMP are within [1.000, 999.000]

siuCpuLdMin: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPULDMIN, values [1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:0, margin:0)

siuCpuLdMin: Dwell telemetry for payload LHKSIUCPULDMIN are within [1.000, 999.000]

siuCpuAvLdm: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPUAVLDM, values [3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00, 3.00] (starting with index:0, margin:0)

siuCpuAvLdm: Dwell telemetry for payload LHKSIUCPUAVLDM are within [1.000, 999.000]

siuCpuAvLds: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPUAVLDS, values [1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:0, margin:0)

siuCpuAvLds: Dwell telemetry for payload LHKSIUCPUAVLDS are within [1.000, 999.000]

siuCpuLdMax: Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKSIUCPULDMAX, values [12.00, 12.00, 12.00, 12.00, 12.00, 12.00, 12.00, 12.00, 12.00, 12.00, 12.00] (starting with index:0, margin:0)

siuCpuLdMax: Dwell telemetry for payload LHKSIUCPULDMAX are within [1.000, 999.000]

readDaqFeedCurrent: Read the DAQ feed current as -0.20A

Enable DAQ Feed

: 

readDaqFeedCurrent: Read the DAQ feed current as -0.20A

daqFeedVoltage: DAQ feed voltage 0.05V is within [-1.0, 1.0]

pduTemp: Warning: Overriding limits [23.000, 50.000] with new limits [22.000, 50.000]

pduTemp: PDU temperature 22.21C is within [22.0, 50.0]

: 

daqFeedVoltage: DAQ feed voltage 28.17V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.10A is within [-1.0, 1.0]

pduTemp: Warning: Overriding limits [23.000, 50.000] with new limits [21.000, 50.000]

pduTemp: PDU temperature 21.69C is within [21.0, 50.0]

pduVoltage: Warning: Overriding limits [0.000, 6.000] with new limits [-0.100, 6.000]

pduVoltage: PDU 0 3.3Vvoltage -0.02V is within [-0.10000000000000001, 6.0]

readDaqFeedCurrent: Read the DAQ feed current as 0.00A

Power On PDU

: 

daqFeedVoltage: DAQ feed voltage 28.08V is within [27.0, 29.0]

pduTemp: Warning: Overriding limits [23.000, 50.000] with new limits [21.000, 50.000]

pduTemp: PDU temperature 21.63C is within [21.0, 50.0]

gasuTemp: Warning: Overriding limits [23.000, 30.000] with new limits [21.000, 30.000]

gasuTemp: GASU temperature 21.82C is within [21.0, 30.0]

gasu33V: Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_EBM33V, values [1.01, 3.30, 3.30, 3.28, 3.35] (starting with index:2, margin:0)

gasu33V: Dwell telemetry for payload L_DAQ_P_EBM33V are within [3.000, 3.600]

daqFeedVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_DAQ_V, values [28.12, 28.08, 28.47, 28.03, 28.12] (starting with index:2, margin:0)

daqFeedVoltage: Dwell telemetry for payload VSC_RBPU_DAQ_V are within [27.000, 29.000]

gasuTemp: Checking if dwell telemetry is in range [23.000, 30.000] for payload L_DAQ_P_GASU_T, values [22.15, 21.89, 22.15, 22.34, 22.60] (starting with index:2, margin:0)

gasuTemp: Warning: Dwell telemetry failed. Payload L_DAQ_P_GASU_T value 22.145 is not within [23.000, 30.000]

pduVoltage: Checking if dwell telemetry is in range [0.000, 6.000] for payload L_DAQ_P_PDU_V, values [0.00, 3.37, 3.35, 3.37, 3.36] (starting with index:2, margin:0)

pduVoltage: Dwell telemetry for payload L_DAQ_P_PDU_V are within [0.000, 6.000]

pduTemp: Checking if dwell telemetry is in range [23.000, 50.000] for payload L_DAQ_P_PDU_T, values [21.63, 22.34, 22.21, 22.41, 21.63] (starting with index:2, margin:0)

pduTemp: Warning: Dwell telemetry failed. Payload L_DAQ_P_PDU_T value 22.211 is not within [23.000, 50.000]

gasu25V: Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_EBM25V, values [0.03, 2.50, 2.48, 2.42, 2.43] (starting with index:2, margin:0)

gasu25V: Dwell telemetry for payload L_DAQ_P_EBM25V are within [2.000, 2.600]

gasu25V: Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_GEM25V, values [0.02, 2.44, 2.44, 2.43, 2.50] (starting with index:2, margin:0)

gasu25V: Dwell telemetry for payload L_DAQ_P_GEM25V are within [2.000, 2.600]

gasu33V: Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_GEM33V, values [1.01, 3.34, 3.34, 3.32, 3.32] (starting with index:2, margin:0)

gasu33V: Dwell telemetry for payload L_DAQ_P_GEM33V are within [3.000, 3.600]

daqCurrentDelta: Checking if dwell telemetry is in range [-1.000, 1.500] for payload VSC_RBPU_DAQ_C, values [-0.20, 0.20, 0.05, 0.34, 0.39] (starting with index:2, margin:0)

daqCurrentDelta: Dwell telemetry for payload VSC_RBPU_DAQ_C are within [-1.000, 1.500]

powerOnPdu : Action - Operator forced action mainFeedOn to pass

: 

daqFeedVoltage: DAQ feed voltage 28.12V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.39A is within [-1.0, 1.5]

pduTemp: Warning: PDU temperature 22.21C is not within [23.0, 50.0]

pduTemp: Warning: powerOnPdu : Verification - Operator forced test pduTemp to pass

pduVoltage: PDU 0 3.3Vvoltage 3.35V is within [0.0, 6.0]

gasuTemp: GASU temperature 23.07C is within [23.0, 30.0]

gasuVoltages: AEM/EBM 3.3V voltage 3.32V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.46V is within [2.0, 2.6000000000000001]

gasuVoltages: CRU/GEM 3.3V voltage 3.32V is within [3.0, 3.6000000000000001]

gasuVoltages: CRU/GEM 2.5V voltage 2.46V is within [2.0, 2.6000000000000001]

readDaqFeedCurrent: Read the DAQ feed current as 0.34A

Power On EPU 0

: 

daqFeedVoltage: DAQ feed voltage 27.93V is within [27.0, 29.0]

epuTemp: PDU 0 EPU 0 temperature measured as 20.04C and within the required range of [-30.0, 45.0]

epuPwrMgt: Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP0EPU0PM, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:9, margin:5)

epuPwrMgt: Dwell telemetry for payload LHKP0EPU0PM are within [1.000, 1.000]

epuTemp: Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP0EPU0T, values [20.07, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04, 20.04] (starting with index:9, margin:5)

epuTemp: Dwell telemetry for payload LHKP0EPU0T are within [-30.000, 45.000]

epuCnvt: Checking if dwell telemetry is in range [0.000, 0.000] for payload LHKP0EPU0CNVT, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00] (starting with index:9, margin:5)

epuCnvt: Dwell telemetry for payload LHKP0EPU0CNVT are within [0.000, 0.000]

: 

daqFeedVoltage: DAQ feed voltage 28.08V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.34A is within [-1.0, 1.0]

epuVoltage: PDU 0 EPU 0 3.3V voltage measured as 2.26V and within the required range of [2.0, 3.5]

epuBootTlm: EPU boot telemetry received.

epuTemp: PDU 0 EPU 0 temperature measured as 20.07C and within the required range of [-30.0, 45.0]

readDaqFeedCurrent: Read the DAQ feed current as 0.98A

Secondary boot of EPU 0

: 

epuVoltage: PDU 0 EPU 0 3.3V voltage measured as 2.25V and within the required range of [2.0, 3.5]

epuTemp: PDU 0 EPU 0 temperature measured as 20.10C and within the required range of [-30.0, 45.0]

epuTemp: Sending secondary boot command to EPU 0 using flags hi=0x5400, lo=0xc000 ...

: 

epuHskTlm: EPU 0 CPU junction temperature measured as 43 and within the required range of [1, 999]

epuTemp: PDU 0 EPU 0 temperature measured as 20.97C and within the required range of [-30.0, 45.0]

Power On EPU 1

: 

daqFeedVoltage: DAQ feed voltage 28.17V is within [27.0, 29.0]

epuTemp: PDU 0 EPU 1 temperature measured as 20.12C and within the required range of [-30.0, 45.0]

epuPwrMgt: Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP0EPU1PM, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] (starting with index:8, margin:5)

epuPwrMgt: Dwell telemetry for payload LHKP0EPU1PM are within [1.000, 1.000]

epuCnvt: Checking if dwell telemetry is in range [0.000, 0.000] for payload LHKP0EPU1CNVT, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00] (starting with index:8, margin:5)

epuCnvt: Dwell telemetry for payload LHKP0EPU1CNVT are within [0.000, 0.000]

epuTemp: Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP0EPU1T, values [20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15, 20.15] (starting with index:8, margin:5)

epuTemp: Dwell telemetry for payload LHKP0EPU1T are within [-30.000, 45.000]

: 

daqFeedVoltage: DAQ feed voltage 28.12V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.24A is within [-1.0, 1.0]

epuVoltage: PDU 0 EPU 1 3.3V voltage measured as 2.27V and within the required range of [2.0, 3.5]

epuBootTlm: EPU boot telemetry received.

epuTemp: PDU 0 EPU 1 temperature measured as 20.15C and within the required range of [-30.0, 45.0]

readDaqFeedCurrent: Read the DAQ feed current as 1.51A

Secondary boot of EPU 1

: 

epuVoltage: PDU 0 EPU 1 3.3V voltage measured as 2.26V and within the required range of [2.0, 3.5]

epuTemp: PDU 0 EPU 1 temperature measured as 20.21C and within the required range of [-30.0, 45.0]

epuTemp: Sending secondary boot command to EPU 1 using flags hi=0x5400, lo=0xc000 ...

: 

epuHskTlm: EPU 1 CPU junction temperature measured as 39 and within the required range of [1, 999]

epuTemp: PDU 0 EPU 1 temperature measured as 20.82C and within the required range of [-30.0, 45.0]

Power On TEM 0

: 

daqFeedVoltage: DAQ feed voltage 28.12V is within [27.0, 29.0]

temDaqTemp: PDU 0 TEM 0 DAQ board temperature measured as 20.37C and within the required range of [-40.0, 60.0]

temPsTemp: PDU 0 TEM 0 power supply temperature measured as 20.22C and within the required range of [-40.0, 60.0]

temVoltage: Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0TEM33V, values [0.18, 0.18, 0.18, 0.18, 0.18, 0.18, 0.18, 0.18, 0.18, 0.18, 3.41, 3.41, 3.41, 3.41, 3.41, 3.41, 3.41, 3.40, 3.40, 3.40] (starting with index:9, margin:7)

temVoltage: Dwell telemetry for payload LHKT0TEM33V are within [3.000, 3.500]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V0, values [33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 33.05, 28.07, 28.07, 28.07, 28.07, 28.07, 28.07, 28.07, 28.05, 28.05, 28.05] (starting with index:9, margin:7)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V0 are within [27.000, 29.000]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V1, values [12.66, 12.66, 12.66, 12.66, 12.66, 12.66, 12.66, 12.66, 12.66, 12.66, 28.15, 28.15, 28.15, 28.15, 28.15, 28.15, 28.15, 28.13, 28.13, 28.13] (starting with index:9, margin:7)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V1 are within [27.000, 29.000]

: 

daqFeedVoltage: DAQ feed voltage 27.73V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.20A is within [-1.0, 1.0]

temPsCurrent: Warning: Conversion constant for LDET0TEM28I was not in the database, using the data from the configuration file

temPsCurrent: TEM 0 power supply current measured as -0.45A and within the required range of [-1.0, 5.0]

temVoltage: TEM 0 3.3V voltage measured as 3.40V and within the required range of [3.0, 3.5]

temDaqTemp: PDU 0 TEM 0 DAQ board temperature measured as 20.37C and within the required range of [-40.0, 60.0]

temPsTemp: PDU 0 TEM 0 power supply temperature measured as 20.25C and within the required range of [-40.0, 60.0]

readDaqFeedCurrent: Read the DAQ feed current as 1.37A

Power On TEM 0 CAL

: 

temPsTemp: PDU 0 TEM 0 power supply temperature measured as 20.25C and within the required range of [-30.0, 45.0]

calAfeeTemp: TEM 0 CAL AFEE 0 temperature 1 measured as 27.20C and within the required range of [23.0, 40.0]

calAfeeTemp: TEM 0 CAL AFEE 1 temperature 1 measured as 26.99C and within the required range of [23.0, 40.0]

calAfeeTemp: TEM 0 CAL AFEE 2 temperature 1 measured as 25.99C and within the required range of [23.0, 40.0]

calAfeeTemp: TEM 0 CAL AFEE 3 temperature 1 measured as 25.09C and within the required range of [23.0, 40.0]

calBiasVoltage: Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV0, values [0.12, 0.12, 0.12, 0.12, 0.12, 0.12, 0.12, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25] (starting with index:9, margin:5)

calBiasVoltage: Dwell telemetry for payload LHKT0CALBSV0 are within [0.000, 80.000]

calBiasVoltage: Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV1, values [0.06, 0.06, 0.06, 0.06, 0.06, 0.06, 0.06, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65, 25.65] (starting with index:9, margin:5)

calBiasVoltage: Dwell telemetry for payload LHKT0CALBSV1 are within [0.000, 80.000]

cal33VA: Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VA, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39, 3.39] (starting with index:9, margin:5)

cal33VA: Dwell telemetry for payload LHKT0CAL33VA are within [3.000, 3.500]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V1, values [28.14, 28.14, 28.14, 28.14, 28.14, 28.14, 28.14, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02, 28.02] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V1 are within [27.000, 29.000]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V0, values [28.06, 28.06, 28.06, 28.06, 28.06, 28.06, 28.06, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89, 27.89] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V0 are within [27.000, 29.000]

cal33VD: Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VD, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36, 3.36] (starting with index:9, margin:5)

cal33VD: Dwell telemetry for payload LHKT0CAL33VD are within [3.000, 3.500]

: 

daqFeedVoltage: DAQ feed voltage 28.03V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.63A is within [-1.0, 1.0]

temPsCurrent: Warning: Conversion constant for LDET0TEM28I was not in the database, using the data from the configuration file

temPsCurrent: TEM 0 power supply current measured as -0.17A and within the required range of [-1.0, 5.0]

cal33V: TEM 0 CAL 3.3V digital measured as 3.36V and within the required range of [3.0, 3.5]

cal33V: TEM 0 CAL 3.3V analog measured as 3.39V and within the required range of [3.0, 3.5]

calBias: TEM 0 CAL bias V0 measured as 0.18V and within the required range of [0.0, 80.0]

calBias: TEM 0 CAL bias V1 measured as 25.71V and within the required range of [0.0, 80.0]

calBias: TEM 0 CAL bias current measured as 0.01A and within the required range of [-1.0, 6.0]

calAfeeTemp: TEM 0 CAL AFEE 0 temperature 1 measured as 27.24C and within the required range of [23.0, 40.0]

calAfeeTemp: TEM 0 CAL AFEE 1 temperature 1 measured as 27.03C and within the required range of [23.0, 40.0]

calAfeeTemp: TEM 0 CAL AFEE 2 temperature 1 measured as 25.93C and within the required range of [23.0, 40.0]

calAfeeTemp: TEM 0 CAL AFEE 3 temperature 1 measured as 25.06C and within the required range of [23.0, 40.0]

readDaqFeedCurrent: Read the DAQ feed current as 1.71A

Power On TEM 0 TKR

: 

temPsTemp: PDU 0 TEM 0 power supply temperature measured as 20.25C and within the required range of [-30.0, 45.0]

tkrTemp: TEM 0 TKR cable 0 temperature 0 measured as 26.27C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 0 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 1 temperature 0 measured as 26.16C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 1 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 2 temperature 0 measured as 26.03C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 2 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 3 temperature 0 measured as 27.87C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 3 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 4 temperature 0 measured as 25.49C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 4 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 5 temperature 0 measured as 26.85C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 5 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 6 temperature 0 measured as 24.73C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 6 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 7 temperature 0 measured as 25.76C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 7 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrBiasVoltage: Checking if dwell telemetry is in range [0.000, 100.000] for payload LHKT0TKRBV1, values [0.12, 0.12, 0.12, 0.12, 0.12, 0.12, 0.12, 25.84, 25.84, 25.84, 25.84, 25.84, 25.84, 25.84, 25.90, 25.90, 25.90, 25.90, 25.90, 25.90] (starting with index:9, margin:5)

tkrBiasVoltage: Dwell telemetry for payload LHKT0TKRBV1 are within [0.000, 100.000]

tkrBiasVoltage: Checking if dwell telemetry is in range [0.000, 100.000] for payload LHKT0TKRBV0, values [0.06, 0.06, 0.06, 0.06, 0.06, 0.06, 0.06, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31] (starting with index:9, margin:5)

tkrBiasVoltage: Dwell telemetry for payload LHKT0TKRBV0 are within [0.000, 100.000]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V1, values [28.03, 28.03, 28.03, 28.03, 28.03, 28.03, 28.03, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80, 27.80] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V1 are within [27.000, 29.000]

temPsVoltage: Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V0, values [27.90, 27.90, 27.90, 27.90, 27.90, 27.90, 27.90, 27.56, 27.56, 27.56, 27.56, 27.56, 27.56, 27.56, 27.57, 27.57, 27.57, 27.57, 27.57, 27.57] (starting with index:9, margin:5)

temPsVoltage: Dwell telemetry for payload LHKT0TEM28V0 are within [27.000, 29.000]

tkr15VA: Checking if dwell telemetry is in range [0.000, 2.000] for payload LHKT0TKR15VAA, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44] (starting with index:9, margin:5)

tkr15VA: Dwell telemetry for payload LHKT0TKR15VAA are within [0.000, 2.000]

tkr25VA: Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VAB, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57, 2.57] (starting with index:9, margin:5)

tkr25VA: Dwell telemetry for payload LHKT0TKR25VAB are within [0.000, 3.000]

tkr25VD: Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VD, values [0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 0.00, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53, 2.53] (starting with index:9, margin:5)

tkr25VD: Dwell telemetry for payload LHKT0TKR25VD are within [0.000, 3.000]

: 

daqFeedVoltage: DAQ feed voltage 28.08V is within [27.0, 29.0]

daqCurrentDelta: DAQ feed current delta 0.59A is within [-1.0, 1.0]

temPsCurrent: Warning: Conversion constant for LDET0TEM28I was not in the database, using the data from the configuration file

temPsCurrent: TEM 0 power supply current measured as 0.36A and within the required range of [-1.0, 5.0]

tkrVoltage: TEM 0 TKR 1.5V analog measured as 1.44V and within the required range of [0.0, 2.0]

tkrVoltage: TEM 0 TKR 2.5V digital measured as 2.53V and within the required range of [0.0, 3.0]

tkrVoltage: TEM 0 TKR 2.5V analog measured as 2.57V and within the required range of [0.0, 3.0]

tkrBias: TEM 0 TKR bias V0 measured as 0.31V and within the required range of [0.0, 100.0]

tkrBias: TEM 0 TKR bias V1 measured as 25.59V and within the required range of [0.0, 100.0]

tkrBias: Warning: Conversion constant for LDET0TKRBIASI was not in the database, using the data from the configuration file

tkrBias: TEM 0 TKR bias current measured as -0.00A and within the required range of [-1.0, 10.0]

tkrTemp: TEM 0 TKR cable 0 temperature 0 measured as 26.27C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 0 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 1 temperature 0 measured as 26.16C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 1 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 2 temperature 0 measured as 26.06C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 2 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 3 temperature 0 measured as 27.87C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 3 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 4 temperature 0 measured as 25.46C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 4 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 5 temperature 0 measured as 26.89C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 5 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 6 temperature 0 measured as 24.80C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 6 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 7 temperature 0 measured as 25.82C and within the required range of [-123.0, 40.0]

tkrTemp: TEM 0 TKR cable 7 temperature 1 measured as -114.72C and within the required range of [-123.0, 40.0]

readDaqFeedCurrent: Read the DAQ feed current as 2.29A

Power On ACD free board 0

: 

gasuVoltages: AEM/EBM 3.3V voltage 3.35V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.42V is within [2.0, 2.6000000000000001]

pmtRailTemp: ACD PMT rail temperature 0 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 1 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 2 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 3 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: Read the free board current as 0.00A

freeBoardTemp: Checking if dwell telemetry is in range [-120.000, 30.000] for payload LHKAEMFR0T, values [20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.66, 20.63, 20.63] (starting with index:20, margin:0)

freeBoardTemp: Dwell telemetry for payload LHKAEMFR0T are within [-120.000, 30.000]

freeBoardVoltage: Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKAEMFR0VD, values [0.73, 0.73, 0.73, 0.73, 3.43, 3.43, 3.43, 3.43, 3.43, 3.43, 3.43, 3.55, 3.55, 3.55, 3.55, 3.55, 3.55, 3.55, 3.55, 3.55] (starting with index:20, margin:0)

freeBoardVoltage: Dwell telemetry for payload LHKAEMFR0VD are within [3.000, 3.500]

: 

gasuVoltages: AEM/EBM 3.3V voltage 3.35V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.46V is within [2.0, 2.6000000000000001]

freeBoardVoltage: Warning: Overriding limits [3.000, 3.500] with new limits [3.000, 3.600]

freeBoardVoltage: AEM free board 0 voltage measured as 3.55V and within the required range of [3.0, 3.6000000000000001]

freeBoardCurrentDelta: Free board current delta 0.00A is within [0.0, 0.90000000000000002]

freeBoardTemp: AEM free board 0 temperature measured as 22.39C and within the required range of [-120.0, 30.0]

Power On ACD free board 0 HVBS

: 

gasuVoltages: AEM/EBM 3.3V voltage 3.37V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.46V is within [2.0, 2.6000000000000001]

pmtRailTemp: Warning: ACD PMT rail temperature 0 measured as None which is not within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 1 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 2 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 3 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: Warning: powerOnAcdHvbs : Prerequisite - Operator forced test pmtRailTemp to pass

hvbsVoltage: AEM free board 0 HV1 voltage measured as 10.13V and within the required range of [-60.0, 60.0]

freeBoardCurrent: AEM free board 3.3 current sum measured as 0.00A and within the required range of [-1.0, 10.0]

: 

gasuVoltages: AEM/EBM 3.3V voltage 3.30V is within [3.0, 3.6000000000000001]

gasuVoltages: AEM/EBM 2.5V voltage 2.49V is within [2.0, 2.6000000000000001]

hvbsVoltage: AEM free board 0 HV1 voltage measured as 318.85V and within the required range of [270, 330]

hvbsVoltage: AEM free board 0 HV1 voltage measured as 773.43V and within the required range of [666, 814]

psCurrent: AEM free board 28V current sum measured as 0.00A and within the required range of [-1.0, 10.0]

pmtRailTemp: ACD PMT rail temperature 0 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 1 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 2 measured as -124.77C and within the required range of [-130.0, 30.0]

pmtRailTemp: ACD PMT rail temperature 3 measured as -124.77C and within the required range of [-130.0, 30.0]

Issue 3 Erroneous Commands

: 

: 

badAPID: Bad APID test passed. The result was ('CTS_APIDNOQ', '"APID %d (0x%04x) does not map to an ITC queue"')

invalidPayload: Invalid payload test passed. The result was ('LHK_PRMERR', '"Invalid command parameter: %s %x"')

incompleteCmd: Incomplete command test passed. CVT timeout occurred and EPKTPARM message was observed.

Ambient, Average and Peak Power Consumption

: 

: 

ambientPower: LAT input power measured as 85.96W and within the required range of [0, 750]

averagePower: LAT average input power measured as 88.63W and within the required range of [0, 650]

peakPower: LAT peak input power measured as 97.37W and within the required range of [0, 750]