; LAT Power Off test configuration file for the Testbed
[config]
; Version and release info
version=$Revision: 1.6 $
release=$Name: L00-09-00 $

; Power up configuration entries
globalTimeout=15
useDiagForHsk=1
quietCmdConfirm=1 ;Do not dump command confirmation packet

; derived tlm = c0. c1
; if the database does not contain these,
; then these values are used
LDET0TEM28I=-0.816831064,66.47364558
LDET0CALBIASI=0.001594612,0.970658978
LDET0TKRBIASI=-0.00920029,0.934009526
LDET1TEM28I=1.032593,64.386062
LDET1CALBIASI=0.009748329,0.840703759
LDET1TKRBIASI=0.007250769,0.898664042
LDET2TEM28I=-0.356907,66.14944
LDET2CALBIASI=0.010346336,0.982844144
LDET2TKRBIASI=0.0000856,1.008636459
LDET3TEM28I=-0.737716,66.178137
LDET3CALBIASI=0.009390119,0.908755158
LDET3TKRBIASI=0.010107999,0.868555516
LDET4TEM28I=0.174790706,67.19096671
LDET4CALBIASI=0.001483485,1.210734104
LDET4TKRBIASI=-0.008913677,0.895868352
LDET5TEM28I=0.455078,65.406829
LDET5CALBIASI=0.021057305,0.855412504
LDET5TKRBIASI=0.0124283,0.985558779
LDET6TEM28I=-0.122687,65.834505
LDET6CALBIASI=-0.013289427,0.936459628
LDET6TKRBIASI=0.006052896,0.929541645
LDET7TEM28I=-0.802101,66.911137
LDET7CALBIASI=0.01285937,0.714541364
LDET7TKRBIASI=-0.010729133,1.027943929
LDET8TEM28I=0.07868,65.521303
LDET8CALBIASI=-0.004519302,0.837330559
LDET8TKRBIASI=0.033696328,0.981087855
LDET9TEM28I=-0.064394,65.43163
LDET9CALBIASI=-0.005980961,0.790219841
LDET9TKRBIASI=-0.000830409,0.952330292
LDETATEM28I=-0.299574,65.940853
LDETACALBIASI=-0.019346277,1.06419473
LDETATKRBIASI=0.001904684,0.937296296
LDETBTEM28I=0.852811,65.338217
LDETBCALBIASI=-0.019377004,0.842790874
LDETBTKRBIASI=-0.000456514,0.963454288
LDETCTEM28I=0.424488,65.205263
LDETCCALBIASI=0.007747647,0.937701377
LDETCTKRBIASI=0.003782319,0.92290647
LDETDTEM28I=0.923721,64.885583
LDETDCALBIASI=0.015372718,0.921509874
LDETDTKRBIASI=0.019879484,0.96169932
LDETETEM28I=-0.171376,65.043002
LDETECALBIASI=-0.000704259,0.842599115
LDETETKRBIASI=-0.020746367,0.957764944
LDETFTEM28I=0.593951,64.82078
LDETFCALBIASI=0.00453998,0.945480657
LDETFTKRBIASI=-0.01034264,1.073088547

[steps]
; Step sequence = Step name, [enabled:1, disabled=0]
0=dwellOnStatus,1
;0a=siuOnStatus,0
;0b=daqFeedStatus,0
;0c=pduGasuOnStatus,0
;0d=epuOnStatus,0
;0e=temOnStatus,0
;0f=calOnStatus,0
;0g=tkrOnStatus,0
;0h=freeBoardOnStatus,0
;0i=acdHvbsOnStatus,0
1=powerOffAcdHvbs,1
2=powerOffAcdFreeBoard,1
2a=powerOffAem,1
3=powerOffTkrHvbs,1
4=powerOffTkr,1
5=powerOffCalHvbs,1
6=powerOffCal,1
7=powerOffTem,1
8=powerOffEpu,1
9=powerOffGasuPdu,1
10=powerConsumption,1

[dwellOnStatus]
prerequisite=
verification=
dwellOnSiu=1
dwellOnDaq=1
dwellOnPduGasu=1
dwellOnEpu=1
dwellOnTem=1
dwellOnCal=1
dwellOnTkr=1
dwellOnAcd=1
hskConfig=LhkPowerOnEpu%d%d.st.f
[dwellOnStatus.limits]
siuFeedVoltage=27.0, 29.0
siuFeedCurrent=-1.0, 20.0
siuVoltage=0.0, 6.0
siuTemp=23.0, 50.0
daqFeedVoltage=27.0, 29.0
daqFeedCurrent=-1.0, 20.0
gasu33V = 3.0, 3.6
gasu25V = 2.0, 2.6
gasuTemp=23.0, 30.0
pduVoltage=0.0, 6.0
pduTemp=23.0, 50.0
epuTemp=-30.0, 45.0
;REVISIT: Testbed reports this as 2.25V
epuVoltage=2.0, 3.5
epuPwrMgt=1, 1
epuHskTlm=1, 999
temPsTemp=-40.0, 60.0
temDaqTemp=-40.0, 60.0
temVoltage=3.0, 3.5
temPsVoltage=27.0, 29.0
temPsCurrent=-1.0, 5.0
calAfeeTemp=23.0, 40.0
cal33VD=3.0, 3.5
cal33VA=3.0, 3.5
; REVISIT: Testbed reports V0:0.25V, V1:25.65V
calBiasVoltage=0.0, 80.0
calBiasCurrent=-1.0, 6.0
tkr15VA=0.0, 2.0
tkr25VD=0.0, 3.0
tkr25VA=0.0, 3.0
tkrBiasVoltage=0.0, 100.0
tkrBiasCurrent=-1.0, 10.0
tkrTemp=-123.0, 40.0
gasu33V=3.0, 3.6
gasu25V=2.0, 2.6
freeBoardVoltage=0.0, 29.0
freeBoardCurrent=-1.0, 10.0
freeBoardTemp=-120.0, 30.0
# GARC ID         0       1       2       3       4       5       6       7       8       9      10      11      
# OPS voltage    740     760     720     730     715     745     820     800     755     740     760     745 (+/- 10%)              
hvbsOpsVoltage=666,814,684,836,648,792,657,803,643,787,670,820,738,902,720,880,679,831,666,814,684,836,670,820
psCurrent=-1.0, 10.0
pmtRailTemp=-130.0, 30.0

# Start of On Status
#~ [siuOnStatus]
#~ prerequisite=
#~ verification=siuFeedVoltage, siuFeedCurrent, siuVoltage, siuTemp
#~ [siuOnStatus.limits]
#~ siuFeedVoltage=27.0, 29.0
#~ siuFeedCurrent=-1.0, 20.0
#~ siuVoltage=0.0, 6.0
#~ siuTemp=23.0, 50.0

#~ [daqFeedStatus]
#~ prerequisite=
#~ verification=daqFeedVoltage, daqFeedCurrent
#~ [daqFeedStatus.limits]
#~ daqFeedVoltage=27.0, 29.0
#~ daqFeedCurrent=-1.0, 20.0

#~ [pduGasuOnStatus]
#~ prerequisite=
#~ verification=gasuVoltages, gasuTemp, pduVoltage, pduTemp
#~ [pduGasuOnStatus.limits]
#~ gasu33V = 3.0, 3.6
#~ gasu25V = 2.0, 2.6
#~ gasuTemp=23.0, 30.0
#~ pduVoltage=0.0, 6.0
#~ pduTemp=23.0, 50.0

#~ [epuOnStatus]
#~ prerequisite=
#~ verification=epuTemp, epuVoltage, epuPwrMgt, epuHskTlm
#~ [epuOnStatus.limits]
#~ epuTemp=-30.0, 45.0
#~ ;REVISIT: Testbed reports this as 2.25V
#~ epuVoltage=2.0, 3.5
#~ epuPwrMgt=1, 1
#~ epuHskTlm=1, 999

#~ [temOnStatus]
#~ prerequisite=
#~ verification=temPsTemp, temDaqTemp, temVoltage, temPsVoltage, temPsCurrent
#~ [temOnStatus.limits]
#~ temPsTemp=-40.0, 60.0
#~ temDaqTemp=-40.0, 60.0
#~ temVoltage=3.0, 3.5
#~ temPsVoltage=27.0, 29.0
#~ temPsCurrent=-1.0, 5.0

#~ [calOnStatus]
#~ prerequisite=
#~ verification=calAfeeTemp, cal33V,  calBias
#~ [calOnStatus.limits]
#~ calAfeeTemp=23.0, 40.0
#~ cal33VD=3.0, 3.5
#~ cal33VA=3.0, 3.5
#~ ; REVISIT: Testbed reports V0:0.25V, V1:25.65V
#~ calBiasVoltage=0.0, 80.0
#~ calBiasCurrent=-1.0, 6.0

#~ [tkrOnStatus]
#~ prerequisite=
#~ verification=tkrVoltage, tkrBias, tkrTemp
#~ [tkrOnStatus.limits]
#~ tkr15VA=0.0, 2.0
#~ tkr25VD=0.0, 3.0
#~ tkr25VA=0.0, 3.0
#~ tkrBiasVoltage=0.0, 100.0
#~ tkrBiasCurrent=-1.0, 10.0
#~ tkrTemp=-123.0, 40.0

#~ [freeBoardOnStatus]
#~ prerequisite=
#~ verification=gasuVoltages, freeBoardVoltage, freeBoardCurrent, freeBoardTemp
#~ [freeBoardOnStatus.limits]
#~ gasu33V=3.0, 3.6
#~ gasu25V=2.0, 2.6
#~ freeBoardVoltage=0.0, 29.0
#~ freeBoardCurrent=-1.0, 10.0
#~ freeBoardTemp=-120.0, 30.0

#~ [acdHvbsOnStatus]
#~ prerequisite=
#~ verification=hvbsVoltage, psCurrent, pmtRailTemp
#~ delay=5
#~ [acdHvbsOnStatus.limits]
#~ # GARC ID         0       1       2       3       4       5       6       7       8       9      10      11      
#~ # SAA voltage: 300 (+/- 10%)
#~ hvbsSaaVoltage=270,330,270,330,270,330,270,330,270,330,270,330,270,330,270,330,270,330,270,330,270,330,270,330
#~ # OPS voltage    740     760     720     730     715     745     820     800     755     740     760     745 (+/- 10%)              
#~ hvbsOpsVoltage=666,814,684,836,648,792,657,803,643,787,670,820,738,902,720,880,679,831,666,814,684,836,670,820
#~ hvbsPreVoltage=-1.0, 1.0
#~ psCurrent=-1.0, 10.0
#~ pmtRailTemp=-130.0, 30.0
#~ # End of On Status

# Start of Power Off
[powerOffAcdHvbs]
prerequisite=
verification=hvbsVoltage
minSaaBiasVoltageCount=0
minHvBiasVoltageCount=0
saaBiasVoltageCount=945
delay=5
[powerOffAcdHvbs.limits]
hvbsVoltage=-60.0, 60.0

[powerOffAcdFreeBoard]
prerequisite=hvbsVoltage
verification=gasuVoltages, freeBoardVoltage
#freeBoardList=11,10,9,8,7,6,5,4,3,2,1,0
freeBoardList=0
[powerOffAcdFreeBoard.limits]
gasu33V=3.0, 3.6
gasu25V=2.0, 2.6
freeBoardVoltage=0.0, 29.0
hvbsVoltage=-0.50, 80.0 ;80V allows for minimum ACD HVBS value

[powerOffAem]
prerequisite=freeBoardVoltage
verification=
[powerOffAem.limits]
freeBoardVoltage=-0.1, 0.8

[powerOffTkrHvbs]
prerequisite=
verification=tkrBias
tkrMinBias=0
[powerOffTkrHvbs.limits]
tkrBiasVoltage=0.0, 100.0
tkrBiasCurrent=-1.0, 10.0

[powerOffTkr]
prerequisite=
verification=tkrVoltage
[powerOffTkr.limits]
tkr15VA=0.0, 0.1
tkr25VD=0.0, 0.1
tkr25VA=0.0, 0.1

[powerOffCalHvbs]
prerequisite=
verification=calBias
calMinBias=0
[powerOffCalHvbs.limits]
calBiasVoltage=0.0, 80.0
calBiasCurrent=-1.0, 10.0

[powerOffCal]
prerequisite=
verification=cal33V
[powerOffCal.limits]
cal33VD=0.0, 0.1
cal33VA=0.0, 0.1

[powerOffTem]
prerequisite=
verification=temVoltage
#temList=15,14,13,12,11,10,9,8,7,6,5,4,3,2,1,0
temList=0
delay=5
[powerOffTem.limits]
temVoltage=0.0, 2.0

[powerOffEpu]
prerequisite=
verification=epuVoltage
[powerOffEpu.limits]
epuVoltage=0.0, 0.5

[powerOffGasuPdu]
prerequisite=
verification=
[powerOffGasuPdu.limits]

[powerConsumption]
prerequisite=
verification=ambientPower, averagePower, peakPower
#dwellSeconds=600
dwellSeconds=10
[powerConsumption.limits]
ambientPower=0, 750
averagePower=0, 650
peakPower=0, 750