2006-03-28 19:16:15,249 seAppBase.py:393 INFO  - seAppBase.seStartRun -- Test LatPowerOff starting run, Operator: NOT-DEFINED, Run Id: 101000056, Time Started: 060328191615 -- Tue Mar 28 19:16:15 2006
2006-03-28 19:16:15,251 seAppBase.py:409 DEBUG - seAppBase.seStartRun -- LatPowerOff
2006-03-28 19:16:15,257 LatPowerOff.py:335 DEBUG - LatPowerOff.startRun()
2006-03-28 19:16:15,262 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnEpu01.st.f with file ID 0x23400001=591396865
2006-03-28 19:16:17,666 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000001
2006-03-28 19:16:19,031 SequenceStep.py:447 INFO  - Uploaded file LhkPowerOnEpu01.st.f with file id 0x23400001
2006-03-28 19:16:19,035 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400001
2006-03-28 19:16:19,808 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400001
2006-03-28 19:16:19,813 SequenceStep.py:93 DEBUG - Starting dwellOnStatus prerequisite tests
2006-03-28 19:16:19,817 SequenceStep.py:95 DEBUG - Completed dwellOnStatus prerequisite tests - result:True
2006-03-28 19:16:19,822 DwellOnStatus.py:101 INFO  - Dwelling on the LAT for 30 seconds...
2006-03-28 19:16:49,826 DwellOnStatus.py:230 DEBUG - Starting dwellOnStatus verification tests
2006-03-28 19:16:49,826 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-1.000, 10.000] for payload LHKAFR33ISUM, values [0.00, 0.00, 0.00, 0.00] (starting with index:0, margin:0)
2006-03-28 19:16:49,827 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKAFR33ISUM are within [-1.000, 10.000]
2006-03-28 19:16:49,828 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV0, values [73.99, 74.05, 74.05, 74.05] (starting with index:0, margin:0)
2006-03-28 19:16:49,829 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CALBSV0 are within [0.000, 80.000]
2006-03-28 19:16:49,829 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV1, values [78.74, 78.80, 78.68, 78.74] (starting with index:0, margin:0)
2006-03-28 19:16:49,830 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CALBSV1 are within [0.000, 80.000]
2006-03-28 19:16:49,831 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-15.000, 30.000] for payload LHKAEMFR0T, values [24.15, 24.11, 24.15] (starting with index:0, margin:0)
2006-03-28 19:16:49,832 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKAEMFR0T are within [-15.000, 30.000]
2006-03-28 19:16:49,833 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKT0CALAF1T1, values [28.74, 28.78, 28.78, 28.78] (starting with index:0, margin:0)
2006-03-28 19:16:49,833 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CALAF1T1 are within [-30.000, 45.000]
2006-03-28 19:16:49,834 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC0T1, values [-114.72, -108.07, -114.72, -114.72] (starting with index:0, margin:0)
2006-03-28 19:16:49,835 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC0T1 are within [-123.000, 40.000]
2006-03-28 19:16:49,836 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC0T0, values [29.75, 29.72, 29.72, 29.75] (starting with index:0, margin:0)
2006-03-28 19:16:49,837 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC0T0 are within [-123.000, 40.000]
2006-03-28 19:16:49,837 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 6.000] for payload L_DAQ_P_SIU_V, values [2.36, 2.33, 2.36, 2.34, 2.34, 2.38, 2.36, 2.32, 2.34, 2.34, 2.35, 2.35, 2.36, 2.35, 2.34, 2.35, 2.34, 2.32, 2.34, 2.34, 2.38, 2.38, 2.34, 2.33, 2.38, 2.38, 2.38, 2.34, 2.38, 2.40] (starting with index:0, margin:0)
2006-03-28 19:16:49,839 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_P_SIU_V are within [0.000, 6.000]
2006-03-28 19:16:49,840 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC6T0, values [29.19, 29.19, 29.19, 29.19] (starting with index:0, margin:0)
2006-03-28 19:16:49,840 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC6T0 are within [-123.000, 40.000]
2006-03-28 19:16:49,841 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload L_DAQ_P_SIU_T, values [31.67, 30.91, 31.33, 30.99, 31.50, 30.99, 32.02, 31.59, 30.32, 30.32, 30.99, 30.91, 30.32, 30.57, 30.24, 30.32, 30.82, 30.32, 30.24, 30.40, 31.67, 30.99, 30.24, 31.59, 31.67, 30.82, 30.24, 31.67, 30.91, 32.28] (starting with index:0, margin:0)
2006-03-28 19:16:49,843 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_P_SIU_T are within [-30.000, 45.000]
2006-03-28 19:16:49,843 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKT0CALAF0T1, values [29.00, 29.04, 29.04, 29.00] (starting with index:0, margin:0)
2006-03-28 19:16:49,844 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CALAF0T1 are within [-30.000, 45.000]
2006-03-28 19:16:49,844 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VD, values [2.52, 2.52, 2.52, 2.52] (starting with index:0, margin:0)
2006-03-28 19:16:49,845 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKR25VD are within [0.000, 3.000]
2006-03-28 19:16:49,845 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC7T0, values [29.57, 29.60, 29.53, 29.53] (starting with index:0, margin:0)
2006-03-28 19:16:49,846 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC7T0 are within [-123.000, 40.000]
2006-03-28 19:16:49,846 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC7T1, values [-114.72, -114.72, -114.72, -114.72] (starting with index:0, margin:0)
2006-03-28 19:16:49,847 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC7T1 are within [-123.000, 40.000]
2006-03-28 19:16:49,848 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [2.000, 3.500] for payload LHKP1EPU133V, values [2.26, 2.26, 2.26] (starting with index:0, margin:0)
2006-03-28 19:16:49,848 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1EPU133V are within [2.000, 3.500]
2006-03-28 19:16:49,849 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKT0CALAF2T1, values [28.97, 28.97, 29.00, 29.00] (starting with index:0, margin:0)
2006-03-28 19:16:49,849 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CALAF2T1 are within [-30.000, 45.000]
2006-03-28 19:16:49,850 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKT0CALAF3T1, values [27.95, 27.98, 28.02, 27.91] (starting with index:0, margin:0)
2006-03-28 19:16:49,850 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CALAF3T1 are within [-30.000, 45.000]
2006-03-28 19:16:49,851 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC4T1, values [-114.72, -114.72, -114.72, -114.72] (starting with index:0, margin:0)
2006-03-28 19:16:49,851 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC4T1 are within [-123.000, 40.000]
2006-03-28 19:16:49,852 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC4T0, values [30.02, 30.02, 30.06, 29.98] (starting with index:0, margin:0)
2006-03-28 19:16:49,852 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC4T0 are within [-123.000, 40.000]
2006-03-28 19:16:49,853 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKEPU1CPUJTEMP, values [47.00, 47.00, 47.00] (starting with index:0, margin:0)
2006-03-28 19:16:49,853 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKEPU1CPUJTEMP are within [1.000, 999.000]
2006-03-28 19:16:49,854 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [666.000, 814.000] for payload LHKAEMFR0V1, values [10.13, 9.79, 10.13] (starting with index:0, margin:0)
2006-03-28 19:16:49,855 SequenceStep.py:567 INFO  - <//Waiting for operator acknowledgement: Step: Check if the LAT is Powered On

About to perform limit check for value: 10.130 against limits [666.000, 814.000]. Current outcome is False.
Click OK to accept default limits or enter new limits below.
Clicking on Cancel will fail the limit check and therefore the test.//>
2006-03-28 19:17:09,804 SequenceStep.py:573 INFO  - Operator confirmed the successful completion of manual task
2006-03-28 19:17:09,804 SequenceStep.py:602 WARNING - Dwell telemetry failed. Payload LHKAEMFR0V1 value 10.130 is not within [666.000, 814.000]
2006-03-28 19:17:09,806 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_DAQ_V, values [27.88, 28.08, 28.08, 27.93, 28.03, 27.78, 27.98, 28.22, 27.93, 27.93, 27.73, 27.93, 27.93, 27.73, 28.08, 28.03, 28.22, 28.12, 27.93, 28.08, 28.17, 27.78, 27.93, 27.64, 27.93, 27.93, 27.93, 27.88, 28.17, 27.73] (starting with index:0, margin:0)
2006-03-28 19:17:09,807 SequenceStep.py:585 INFO  - Dwell telemetry for payload VSC_RBPU_DAQ_V are within [27.000, 29.000]
2006-03-28 19:17:09,808 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [2.000, 3.500] for payload LHKP1EPU033V, values [2.24, 2.24, 2.24] (starting with index:0, margin:0)
2006-03-28 19:17:09,809 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1EPU033V are within [2.000, 3.500]
2006-03-28 19:17:09,810 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP1EPU0T, values [29.12, 29.16, 29.16] (starting with index:0, margin:0)
2006-03-28 19:17:09,811 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1EPU0T are within [-30.000, 45.000]
2006-03-28 19:17:09,812 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload L_DAQ_P_GASU_T, values [25.63, 25.92, 25.63, 25.48, 25.99, 25.48, 25.99, 25.92, 25.70, 25.48, 25.99, 25.99, 25.48, 25.99, 25.48, 25.48, 25.92, 25.99, 26.28, 25.48, 25.92, 25.48, 25.99, 25.56, 25.99, 25.99, 25.06, 25.41, 25.34, 25.41] (starting with index:0, margin:0)
2006-03-28 19:17:09,814 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_P_GASU_T are within [-30.000, 45.000]
2006-03-28 19:17:09,816 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC3T0, values [31.75, 31.79, 31.75, 31.75] (starting with index:0, margin:0)
2006-03-28 19:17:09,816 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC3T0 are within [-123.000, 40.000]
2006-03-28 19:17:09,817 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC6T1, values [-114.72, -108.07, -108.07, -108.07] (starting with index:0, margin:0)
2006-03-28 19:17:09,818 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC6T1 are within [-123.000, 40.000]
2006-03-28 19:17:09,819 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC2T1, values [-114.72, -114.72, -114.72, -114.72] (starting with index:0, margin:0)
2006-03-28 19:17:09,820 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC2T1 are within [-123.000, 40.000]
2006-03-28 19:17:09,821 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC2T0, values [29.79, 29.79, 29.79, 29.79] (starting with index:0, margin:0)
2006-03-28 19:17:09,821 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC2T0 are within [-123.000, 40.000]
2006-03-28 19:17:09,822 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_EBM33V, values [3.32, 3.30, 3.35, 3.33, 3.33, 3.35, 3.32, 3.40, 3.35, 3.35, 3.34, 3.33, 3.35, 3.32, 3.29, 3.28, 3.35, 3.32, 3.35, 3.30, 3.32, 3.27, 3.35, 3.32, 3.35, 3.37, 3.32, 3.32, 3.34, 3.34] (starting with index:0, margin:0)
2006-03-28 19:17:09,824 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_P_EBM33V are within [3.000, 3.600]
2006-03-28 19:17:09,824 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VA, values [3.38, 3.38, 3.38, 3.38] (starting with index:0, margin:0)
2006-03-28 19:17:09,825 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CAL33VA are within [3.000, 3.500]
2006-03-28 19:17:09,826 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC3T1, values [-114.72, -114.72, -114.72, -114.72] (starting with index:0, margin:0)
2006-03-28 19:17:09,827 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC3T1 are within [-123.000, 40.000]
2006-03-28 19:17:09,828 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VD, values [3.36, 3.36, 3.36, 3.36] (starting with index:0, margin:0)
2006-03-28 19:17:09,829 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0CAL33VD are within [3.000, 3.500]
2006-03-28 19:17:09,829 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [2.900, 3.800] for payload LHKAEMFR0VD, values [3.55, 3.54, 3.55] (starting with index:0, margin:0)
2006-03-28 19:17:09,830 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKAEMFR0VD are within [2.900, 3.800]
2006-03-28 19:17:09,831 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 2.000] for payload LHKT0TKR15VAA, values [1.43, 1.43, 1.43, 1.43] (starting with index:0, margin:0)
2006-03-28 19:17:09,832 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKR15VAA are within [0.000, 2.000]
2006-03-28 19:17:09,833 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC1T0, values [29.68, 29.64, 29.68, 29.64] (starting with index:0, margin:0)
2006-03-28 19:17:09,834 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC1T0 are within [-123.000, 40.000]
2006-03-28 19:17:09,835 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC1T1, values [-108.07, -108.07, -108.07, -108.07] (starting with index:0, margin:0)
2006-03-28 19:17:09,835 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC1T1 are within [-123.000, 40.000]
2006-03-28 19:17:09,836 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_EBM25V, values [2.53, 2.42, 2.42, 2.42, 2.46, 2.46, 2.48, 2.48, 2.44, 2.43, 2.47, 2.50, 2.43, 2.46, 2.46, 2.43, 2.51, 2.46, 2.46, 2.47, 2.46, 2.45, 2.46, 2.51, 2.46, 2.46, 2.46, 2.46, 2.47, 2.50] (starting with index:0, margin:0)
2006-03-28 19:17:09,838 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_P_EBM25V are within [2.000, 2.600]
2006-03-28 19:17:09,839 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_GEM25V, values [2.46, 2.46, 2.50, 2.46, 2.44, 2.46, 2.46, 2.44, 2.52, 2.48, 2.48, 2.47, 2.50, 2.46, 2.43, 2.47, 2.48, 2.43, 2.50, 2.45, 2.46, 2.46, 2.45, 2.46, 2.50, 2.44, 2.46, 2.46, 2.47, 2.46] (starting with index:0, margin:0)
2006-03-28 19:17:09,840 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_P_GEM25V are within [2.000, 2.600]
2006-03-28 19:17:09,841 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_GEM33V, values [3.31, 3.30, 3.30, 3.30, 3.35, 3.29, 3.35, 3.28, 3.31, 3.29, 3.32, 3.32, 3.32, 3.35, 3.30, 3.32, 3.32, 3.32, 3.36, 3.30, 3.32, 3.28, 3.33, 3.27, 3.33, 3.32, 3.34, 3.27, 3.33, 3.32] (starting with index:0, margin:0)
2006-03-28 19:17:09,843 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_P_GEM33V are within [3.000, 3.600]
2006-03-28 19:17:09,843 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP1TEM0PST, values [24.61, 24.61, 24.61] (starting with index:0, margin:0)
2006-03-28 19:17:09,844 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1TEM0PST are within [-30.000, 45.000]
2006-03-28 19:17:09,845 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0TEM33V, values [3.40, 3.40, 3.40, 3.40] (starting with index:0, margin:0)
2006-03-28 19:17:09,846 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TEM33V are within [3.000, 3.500]
2006-03-28 19:17:09,847 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-1.000, 20.000] for payload VSC_RBPU_DAQ_C, values [2.73, 2.20, 2.39, 2.49, 2.15, 2.34, 2.34, 2.34, 2.69, 2.64, 2.29, 2.15, 2.29, 2.59, 2.39, 2.29, 2.39, 2.29, 2.59, 2.34, 2.34, 2.59, 2.29, 2.49, 2.49, 2.69, 2.34, 2.49, 2.34, 2.34] (starting with index:0, margin:0)
2006-03-28 19:17:09,848 SequenceStep.py:585 INFO  - Dwell telemetry for payload VSC_RBPU_DAQ_C are within [-1.000, 20.000]
2006-03-28 19:17:09,849 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 105.000] for payload LHKT0TKRBV1, values [25.84, 25.90, 25.77, 25.84] (starting with index:0, margin:0)
2006-03-28 19:17:09,850 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRBV1 are within [0.000, 105.000]
2006-03-28 19:17:09,851 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 105.000] for payload LHKT0TKRBV0, values [0.25, 0.31, 0.31, 0.31] (starting with index:0, margin:0)
2006-03-28 19:17:09,852 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRBV0 are within [0.000, 105.000]
2006-03-28 19:17:09,852 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP1EPU0PM, values [1.00, 1.00, 1.00] (starting with index:0, margin:0)
2006-03-28 19:17:09,854 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1EPU0PM are within [1.000, 1.000]
2006-03-28 19:17:09,854 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP1TEM0PCT, values [26.24, 26.27, 26.27] (starting with index:0, margin:0)
2006-03-28 19:17:09,855 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1TEM0PCT are within [-30.000, 45.000]
2006-03-28 19:17:09,856 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V1, values [27.78, 27.79, 27.77, 27.78] (starting with index:0, margin:0)
2006-03-28 19:17:09,857 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TEM28V1 are within [27.000, 29.000]
2006-03-28 19:17:09,858 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V0, values [27.56, 27.56, 27.54, 27.55] (starting with index:0, margin:0)
2006-03-28 19:17:09,859 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TEM28V0 are within [27.000, 29.000]
2006-03-28 19:17:09,860 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload L_DAQ_R_PDU_T, values [25.41, 24.85, 24.78, 24.78, 24.36, 24.36, 24.29, 24.01, 24.78, 24.22, 24.29, 24.85, 24.22, 24.50, 24.22, 24.22, 24.78, 24.22, 24.50, 24.22, 24.50, 23.95, 23.74, 24.29, 24.29, 24.22, 24.29, 24.78, 24.50, 24.85] (starting with index:0, margin:0)
2006-03-28 19:17:09,861 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_R_PDU_T are within [-30.000, 45.000]
2006-03-28 19:17:09,862 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP1EPU1PM, values [1.00, 1.00, 1.00] (starting with index:0, margin:0)
2006-03-28 19:17:09,863 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1EPU1PM are within [1.000, 1.000]
2006-03-28 19:17:09,864 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 6.000] for payload L_DAQ_R_PDU_V, values [3.38, 3.36, 3.35, 3.35, 3.32, 3.36, 3.36, 3.36, 3.35, 3.41, 3.36, 3.35, 3.35, 3.32, 3.36, 3.37, 3.35, 3.36, 3.35, 3.35, 3.35, 3.35, 3.36, 3.36, 3.36, 3.35, 3.36, 3.36, 3.33, 3.35] (starting with index:0, margin:0)
2006-03-28 19:17:09,865 SequenceStep.py:585 INFO  - Dwell telemetry for payload L_DAQ_R_PDU_V are within [0.000, 6.000]
2006-03-28 19:17:09,866 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP1EPU1T, values [27.83, 27.87, 27.83] (starting with index:0, margin:0)
2006-03-28 19:17:09,867 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKP1EPU1T are within [-30.000, 45.000]
2006-03-28 19:17:09,868 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC5T0, values [30.87, 30.87, 30.87, 30.83] (starting with index:0, margin:0)
2006-03-28 19:17:09,869 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC5T0 are within [-123.000, 40.000]
2006-03-28 19:17:09,870 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC5T1, values [-114.72, -114.72, -114.72, -114.72] (starting with index:0, margin:0)
2006-03-28 19:17:09,871 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKRC5T1 are within [-123.000, 40.000]
2006-03-28 19:17:09,871 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VAB, values [2.56, 2.56, 2.56, 2.56] (starting with index:0, margin:0)
2006-03-28 19:17:09,872 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKT0TKR25VAB are within [0.000, 3.000]
2006-03-28 19:17:09,873 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [-1.000, 20.000] for payload VSC_RBPU_SIU_C, values [0.55, 0.50, 0.55, 0.54, 0.56, 0.54, 0.55, 0.52, 0.55, 0.57, 0.58, 0.55, 0.57, 0.58, 0.56, 0.54, 0.55, 0.57, 0.58, 0.57, 0.54, 0.54, 0.55, 0.56, 0.54, 0.59, 0.58, 0.54, 0.54, 0.55] (starting with index:0, margin:0)
2006-03-28 19:17:09,875 SequenceStep.py:585 INFO  - Dwell telemetry for payload VSC_RBPU_SIU_C are within [-1.000, 20.000]
2006-03-28 19:17:09,876 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKEPU0CPUJTEMP, values [51.00, 51.00, 51.00] (starting with index:0, margin:0)
2006-03-28 19:17:09,877 SequenceStep.py:585 INFO  - Dwell telemetry for payload LHKEPU0CPUJTEMP are within [1.000, 999.000]
2006-03-28 19:17:09,878 SequenceStep.py:585 INFO  - Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_SIU_V, values [28.17, 28.03, 28.17, 28.12, 28.03, 28.12, 28.08, 28.03, 28.17, 28.12, 28.12, 28.08, 28.12, 27.93, 28.12, 28.12, 28.27, 27.73, 27.88, 28.12, 27.93, 28.17, 27.93, 28.08, 27.93, 27.93, 27.98, 28.12, 28.22, 28.08] (starting with index:0, margin:0)
2006-03-28 19:17:09,879 SequenceStep.py:585 INFO  - Dwell telemetry for payload VSC_RBPU_SIU_V are within [27.000, 29.000]
2006-03-28 19:17:09,880 DwellOnStatus.py:232 DEBUG - Completed dwellOnStatus verification tests - result:False
2006-03-28 19:17:09,881 testAppBase.py:496 WARNING - dwellOnStatus : Verification - Verification tests failed (Step: Check if the LAT is Powered On), Retry, Abort (Fail) or Continue (Pass)?
2006-03-28 19:17:11,813 SequenceStep.py:602 WARNING - dwellOnStatus : Verification - Operator forced verification tests to pass
2006-03-28 19:17:11,814 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:17:12,828 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:17:12,834 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnPdu1.st.f with file ID 0x23400002=591396866
2006-03-28 19:17:15,694 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000002
2006-03-28 19:17:17,009 SequenceStep.py:447 INFO  - Uploaded file LhkPowerOnPdu1.st.f with file id 0x23400002
2006-03-28 19:17:17,013 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:17:17,835 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:17:17,840 SequenceStep.py:93 DEBUG - Starting powerOffAcdHvbs prerequisite tests
2006-03-28 19:17:17,845 SequenceStep.py:95 DEBUG - Completed powerOffAcdHvbs prerequisite tests - result:True
2006-03-28 19:17:17,849 PowerOffAcdHvbs.py:79 INFO  - Configuring the ACD bias voltage for free board 0 with the SAA level of 945 counts and operational level of 0 counts...
2006-03-28 19:17:18,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:18,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:18,793 LIM.py:260 DEBUG - 	Action        : 56
2006-03-28 19:17:18,800 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:17:18,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:18,801 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:18,823 PowerOffAcdHvbs.py:95 INFO  - Stepping down to SAA voltage...
2006-03-28 19:17:19,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:19,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:19,794 LIM.py:260 DEBUG - 	Action        : 60
2006-03-28 19:17:19,796 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:19,796 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:19,797 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:19,800 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:19,801 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:19,801 LIM.py:260 DEBUG - 	Action        : 19
2006-03-28 19:17:19,804 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:19,804 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:19,805 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:24,842 PowerOffAcdHvbs.py:103 INFO  - Verified that ACD bias voltages are configured.
2006-03-28 19:17:24,842 PowerOffAcdHvbs.py:108 INFO  - Verified HV State Change.
2006-03-28 19:17:24,843 PowerOffAcdHvbs.py:114 INFO  - Stepping down to minimum voltage...
2006-03-28 19:17:25,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:25,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:25,794 LIM.py:260 DEBUG - 	Action        : 60
2006-03-28 19:17:25,796 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:25,796 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:25,797 LIM.py:264 DEBUG - 	HV Allow      : 1
2006-03-28 19:17:25,801 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:25,801 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:25,802 LIM.py:260 DEBUG - 	Action        : 21
2006-03-28 19:17:25,804 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:25,804 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:25,805 LIM.py:264 DEBUG - 	HV Allow      : 1
2006-03-28 19:17:30,809 PowerOffAcdHvbs.py:122 INFO  - Verified HV State Change.
2006-03-28 19:17:30,809 PowerOffAcdHvbs.py:131 INFO  - Configuring the ACD bias voltage for free board 0 with the SAA level of 0 counts and operational level of 0 counts...
2006-03-28 19:17:31,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:31,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:31,794 LIM.py:260 DEBUG - 	Action        : 56
2006-03-28 19:17:31,800 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:17:31,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:31,801 LIM.py:264 DEBUG - 	HV Allow      : 1
2006-03-28 19:17:31,839 PowerOffAcdHvbs.py:139 INFO  - Disallowing HV voltage...
2006-03-28 19:17:32,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:32,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:32,794 LIM.py:260 DEBUG - 	Action        : 60
2006-03-28 19:17:32,796 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:32,796 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:32,797 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:32,800 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:32,801 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:32,801 LIM.py:260 DEBUG - 	Action        : 19
2006-03-28 19:17:32,803 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:32,804 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:32,804 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:32,855 PowerOffAcdHvbs.py:146 INFO  - Verified that ACD bias voltages are configured.
2006-03-28 19:17:32,855 PowerOffAcdHvbs.py:151 INFO  - Verified HV State Change.
2006-03-28 19:17:32,856 PowerOffAcdHvbs.py:155 INFO  - Completed Set ACD Bias Voltage to Minimum action for free board 0, result:True
2006-03-28 19:17:32,856 PowerOffAcdHvbs.py:162 DEBUG - Starting powerOffAcdHvbs verification tests
2006-03-28 19:17:32,857 PowerSequenceStep.py:1733 INFO  - Executing LIM SAA enter command
2006-03-28 19:17:33,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:33,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:33,794 LIM.py:260 DEBUG - 	Action        : 45
2006-03-28 19:17:33,796 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:33,796 LIM.py:263 DEBUG - 	SaaTransit    : 1
2006-03-28 19:17:33,797 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:33,800 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:33,801 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:33,801 LIM.py:260 DEBUG - 	Action        : 19
2006-03-28 19:17:33,804 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:33,804 LIM.py:263 DEBUG - 	SaaTransit    : 1
2006-03-28 19:17:33,805 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:33,822 PowerSequenceStep.py:1740 INFO  - Verified SAA entry.
2006-03-28 19:17:38,824 PowerSequenceStep.py:924 INFO  - Checking if AEM free board 0 HV1 voltage is within range [-60.0, 60.0]...
2006-03-28 19:17:40,830 SequenceStep.py:585 INFO  - AEM free board 0 HV1 voltage measured as 10.13V and within the required range of [-60.0, 60.0]
2006-03-28 19:17:40,831 PowerSequenceStep.py:1758 INFO  - Configuring LIM to allow setting of the HV
2006-03-28 19:17:41,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:41,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:41,793 LIM.py:260 DEBUG - 	Action        : 60
2006-03-28 19:17:41,795 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:41,796 LIM.py:263 DEBUG - 	SaaTransit    : 1
2006-03-28 19:17:41,796 LIM.py:264 DEBUG - 	HV Allow      : 1
2006-03-28 19:17:41,846 PowerSequenceStep.py:1765 INFO  - Verified HV State Change.
2006-03-28 19:17:41,846 PowerSequenceStep.py:1772 INFO  - Executing LIM SAA exit command
2006-03-28 19:17:42,792 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:42,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:42,793 LIM.py:260 DEBUG - 	Action        : 45
2006-03-28 19:17:42,796 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:42,796 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:42,796 LIM.py:264 DEBUG - 	HV Allow      : 1
2006-03-28 19:17:42,800 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:42,800 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:42,801 LIM.py:260 DEBUG - 	Action        : 21
2006-03-28 19:17:42,803 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:42,803 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:42,804 LIM.py:264 DEBUG - 	HV Allow      : 1
2006-03-28 19:17:42,814 PowerSequenceStep.py:1779 INFO  - Verified SAA exit.
2006-03-28 19:17:47,815 PowerSequenceStep.py:1788 INFO  - Configuring LIM to disallow setting of the HV
2006-03-28 19:17:48,792 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:48,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:48,793 LIM.py:260 DEBUG - 	Action        : 60
2006-03-28 19:17:48,795 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:48,796 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:48,796 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:48,800 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:48,800 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:48,801 LIM.py:260 DEBUG - 	Action        : 19
2006-03-28 19:17:48,803 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:17:48,803 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:48,804 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:48,829 PowerSequenceStep.py:1795 INFO  - Verified HV State Change.
2006-03-28 19:17:48,829 PowerSequenceStep.py:924 INFO  - Checking if AEM free board 0 HV1 voltage is within range [-60.0, 60.0]...
2006-03-28 19:17:50,837 SequenceStep.py:585 INFO  - AEM free board 0 HV1 voltage measured as 10.13V and within the required range of [-60.0, 60.0]
2006-03-28 19:17:50,838 PowerOffAcdHvbs.py:185 DEBUG - Completed powerOffAcdHvbs verification tests - result:True
2006-03-28 19:17:50,838 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:17:51,803 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:17:51,808 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:17:52,830 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:17:52,836 PowerOffAcdFreeBoard.py:52 DEBUG - Starting powerOffAcdFreeBoard prerequisite tests
2006-03-28 19:17:52,842 PowerSequenceStep.py:924 INFO  - Checking if AEM free board 0 HV1 voltage is within range [-0.5, 80.0]...
2006-03-28 19:17:54,804 SequenceStep.py:585 INFO  - AEM free board 0 HV1 voltage measured as 10.13V and within the required range of [-0.5, 80.0]
2006-03-28 19:17:54,804 PowerOffAcdFreeBoard.py:64 DEBUG - Completed powerOffAcdFreeBoard prerequisite tests - result:True
2006-03-28 19:17:54,805 PowerOffAcdFreeBoard.py:74 INFO  - Powering off free board 0...
2006-03-28 19:17:55,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:55,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:55,793 LIM.py:260 DEBUG - 	Action        : 8
2006-03-28 19:17:55,799 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:17:55,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:55,800 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:55,804 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:17:55,805 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:17:55,805 LIM.py:260 DEBUG - 	Action        : 5
2006-03-28 19:17:55,811 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:17:55,811 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:17:55,812 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:17:55,816 PowerOffAcdFreeBoard.py:84 INFO  - Verified power off action.
2006-03-28 19:17:55,816 PowerOffAcdFreeBoard.py:88 INFO  - Completed ACD power off action for free board 0, result:True
2006-03-28 19:17:55,817 PowerOffAcdFreeBoard.py:95 DEBUG - Starting powerOffAcdFreeBoard verification tests
2006-03-28 19:17:55,817 PowerSequenceStep.py:779 INFO  - Checking if the AEM/EBM 3.3V and AEM/EBM 2.5V voltages are within range [[3.0, 3.6000000000000001], [2.0, 2.6000000000000001]]...
2006-03-28 19:17:56,383 SequenceStep.py:585 INFO  - AEM/EBM 3.3V voltage 3.36V is within [3.0, 3.6000000000000001]
2006-03-28 19:17:56,383 SequenceStep.py:585 INFO  - AEM/EBM 2.5V voltage 2.53V is within [2.0, 2.6000000000000001]
2006-03-28 19:17:56,384 PowerSequenceStep.py:878 INFO  - Checking if AEM free board 0 voltage is within range [-0.10000000000000001, 0.80000000000000004]...
2006-03-28 19:17:58,840 SequenceStep.py:585 INFO  - AEM free board 0 voltage measured as 0.73V and within the required range of [-0.10000000000000001, 0.80000000000000004]
2006-03-28 19:17:58,841 PowerOffAcdFreeBoard.py:110 DEBUG - Completed powerOffAcdFreeBoard verification tests - result:True
2006-03-28 19:17:58,841 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:17:59,806 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:17:59,811 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:00,833 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:00,838 PowerOffAem.py:51 DEBUG - Starting powerOffAem prerequisite tests
2006-03-28 19:18:00,847 PowerSequenceStep.py:878 INFO  - Checking if AEM free board 0 voltage is within range [-0.10000000000000001, 0.80000000000000004]...
2006-03-28 19:18:02,809 SequenceStep.py:585 INFO  - AEM free board 0 voltage measured as 0.73V and within the required range of [-0.10000000000000001, 0.80000000000000004]
2006-03-28 19:18:02,810 PowerOffAem.py:62 DEBUG - Completed powerOffAem prerequisite tests - result:True
2006-03-28 19:18:02,810 PowerOffAem.py:72 INFO  - Powering off the AEM...
2006-03-28 19:18:03,792 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:03,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:03,793 LIM.py:260 DEBUG - 	Action        : 8
2006-03-28 19:18:03,799 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:03,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:03,800 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:03,804 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:03,804 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:03,805 LIM.py:260 DEBUG - 	Action        : 5
2006-03-28 19:18:03,811 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:03,812 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:03,812 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:04,832 PowerOffAem.py:82 INFO  - Verified power off action.
2006-03-28 19:18:04,833 PowerOffAem.py:86 INFO  - Completed AEM power off action, result:True
2006-03-28 19:18:04,833 PowerOffAem.py:93 DEBUG - Starting powerOffAem verification tests
2006-03-28 19:18:04,834 PowerOffAem.py:101 DEBUG - Completed powerOffAem verification tests - result:True
2006-03-28 19:18:04,834 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:05,801 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:05,807 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:06,824 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:06,829 SequenceStep.py:93 DEBUG - Starting powerOffTkrHvbs prerequisite tests
2006-03-28 19:18:06,837 SequenceStep.py:95 DEBUG - Completed powerOffTkrHvbs prerequisite tests - result:True
2006-03-28 19:18:06,839 PowerOffTkrHvbs.py:52 INFO  - Setting TEM 0 TKR bias voltage to 0x0...
2006-03-28 19:18:07,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:07,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:07,793 LIM.py:260 DEBUG - 	Action        : 58
2006-03-28 19:18:07,799 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:07,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:07,800 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:07,805 PowerOffTkrHvbs.py:73 INFO  - Verified TKR bias voltage change.
2006-03-28 19:18:07,805 PowerOffTkrHvbs.py:77 INFO  - Completed Set TKR bias voltage to minumum action for TKR 0, result:True
2006-03-28 19:18:07,806 PowerOffTkrHvbs.py:84 DEBUG - Starting powerOffTkrHvbs verification tests
2006-03-28 19:18:07,807 PowerSequenceStep.py:1493 INFO  - Checking if TEM 0 TKR bias voltages are within range [[0.0, 105.0], [0.0, 105.0], [-1.0, 10.0]]...
2006-03-28 19:18:09,807 SequenceStep.py:585 INFO  - TEM 0 TKR bias V0 measured as 0.31V and within the required range of [0.0, 105.0]
2006-03-28 19:18:09,808 SequenceStep.py:585 INFO  - TEM 0 TKR bias V1 measured as 25.84V and within the required range of [0.0, 105.0]
2006-03-28 19:18:09,809 SequenceStep.py:602 WARNING - Conversion constant for LDET0TKRBIASI was not in the database, using the data from the configuration file
2006-03-28 19:18:09,810 SequenceStep.py:585 INFO  - TEM 0 TKR bias current measured as -0.00A and within the required range of [-1.0, 10.0]
2006-03-28 19:18:09,811 PowerOffTkrHvbs.py:97 DEBUG - Completed powerOffTkrHvbs verification tests - result:True
2006-03-28 19:18:09,812 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:10,827 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:10,832 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:11,805 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:11,810 SequenceStep.py:93 DEBUG - Starting powerOffTkr prerequisite tests
2006-03-28 19:18:11,819 SequenceStep.py:95 DEBUG - Completed powerOffTkr prerequisite tests - result:True
2006-03-28 19:18:11,819 PowerOffTkr.py:51 INFO  - Powering off TEM 0 TKR...
2006-03-28 19:18:12,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:12,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:12,794 LIM.py:260 DEBUG - 	Action        : 8
2006-03-28 19:18:12,800 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:12,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:12,801 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:13,992 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:13,993 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:13,994 LIM.py:260 DEBUG - 	Action        : 5
2006-03-28 19:18:14,000 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:14,000 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:14,000 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:14,040 PowerOffTkr.py:61 INFO  - Verified power off action.
2006-03-28 19:18:14,041 PowerOffTkr.py:65 INFO  - Completed power off action for TKR 0, result:True
2006-03-28 19:18:14,041 PowerOffTkr.py:72 DEBUG - Starting powerOffTkr verification tests
2006-03-28 19:18:14,042 PowerSequenceStep.py:1404 INFO  - Checking if TEM 0 TKR voltages are within range [[0.0, 0.10000000000000001], [0.0, 0.10000000000000001], [0.0, 0.10000000000000001]]...
2006-03-28 19:18:15,799 SequenceStep.py:585 INFO  - TEM 0 TKR 1.5V analog measured as 0.00V and within the required range of [0.0, 0.10000000000000001]
2006-03-28 19:18:15,800 SequenceStep.py:585 INFO  - TEM 0 TKR 2.5V digital measured as 0.00V and within the required range of [0.0, 0.10000000000000001]
2006-03-28 19:18:15,801 SequenceStep.py:585 INFO  - TEM 0 TKR 2.5V analog measured as 0.01V and within the required range of [0.0, 0.10000000000000001]
2006-03-28 19:18:15,801 PowerOffTkr.py:86 DEBUG - Completed powerOffTkr verification tests - result:True
2006-03-28 19:18:15,802 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:16,815 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:16,820 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:17,841 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:17,850 SequenceStep.py:93 DEBUG - Starting powerOffCalHvbs prerequisite tests
2006-03-28 19:18:17,854 SequenceStep.py:95 DEBUG - Completed powerOffCalHvbs prerequisite tests - result:True
2006-03-28 19:18:17,855 PowerOffCalHvbs.py:50 INFO  - Setting TEM 0 CAL bias voltage to 0x0...
2006-03-28 19:18:18,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:18,794 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:18,795 LIM.py:260 DEBUG - 	Action        : 57
2006-03-28 19:18:18,801 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:18,801 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:18,802 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:18,821 PowerOffCalHvbs.py:59 INFO  - Verified CAL bias voltage change.
2006-03-28 19:18:18,822 PowerOffCalHvbs.py:63 INFO  - Completed Set CAL bias voltage to minumum action for TKR 0, result:True
2006-03-28 19:18:18,823 PowerOffCalHvbs.py:70 DEBUG - Starting powerOffCalHvbs verification tests
2006-03-28 19:18:18,823 PowerSequenceStep.py:1254 INFO  - Checking if TEM 0 CAL bias voltages are within range [[0.0, 80.0], [0.0, 80.0], [-1.0, 10.0]]...
2006-03-28 19:18:20,824 SequenceStep.py:585 INFO  - TEM 0 CAL bias V0 measured as 73.99V and within the required range of [0.0, 80.0]
2006-03-28 19:18:20,824 SequenceStep.py:585 INFO  - TEM 0 CAL bias V1 measured as 78.62V and within the required range of [0.0, 80.0]
2006-03-28 19:18:20,825 SequenceStep.py:602 WARNING - Conversion constant for LDET0CALBIASI was not in the database, using the data from the configuration file
2006-03-28 19:18:20,826 SequenceStep.py:585 INFO  - TEM 0 CAL bias current measured as 0.00A and within the required range of [-1.0, 10.0]
2006-03-28 19:18:20,827 PowerOffCalHvbs.py:83 DEBUG - Completed powerOffCalHvbs verification tests - result:True
2006-03-28 19:18:20,827 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:21,840 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:21,845 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:22,817 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:22,826 SequenceStep.py:93 DEBUG - Starting powerOffCal prerequisite tests
2006-03-28 19:18:22,830 SequenceStep.py:95 DEBUG - Completed powerOffCal prerequisite tests - result:True
2006-03-28 19:18:22,831 PowerOffCal.py:51 INFO  - Powering off TEM 0 CAL...
2006-03-28 19:18:23,792 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:23,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:23,794 LIM.py:260 DEBUG - 	Action        : 8
2006-03-28 19:18:23,799 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:23,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:23,800 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:24,993 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:24,993 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:24,994 LIM.py:260 DEBUG - 	Action        : 5
2006-03-28 19:18:24,999 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:25,000 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:25,001 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:25,053 PowerOffCal.py:61 INFO  - Verified power off action.
2006-03-28 19:18:25,053 PowerOffCal.py:65 INFO  - Completed power off action for CAL 0, result:True
2006-03-28 19:18:25,054 PowerOffCal.py:72 DEBUG - Starting powerOffCal verification tests
2006-03-28 19:18:25,055 PowerSequenceStep.py:1186 INFO  - Checking if TEM 0 CAL 3.3V digital and analog are within range [[0.0, 0.10000000000000001], [0.0, 0.10000000000000001]]...
2006-03-28 19:18:26,817 SequenceStep.py:585 INFO  - TEM 0 CAL 3.3V digital measured as 0.00V and within the required range of [0.0, 0.10000000000000001]
2006-03-28 19:18:26,818 SequenceStep.py:585 INFO  - TEM 0 CAL 3.3V analog measured as 0.01V and within the required range of [0.0, 0.10000000000000001]
2006-03-28 19:18:26,818 PowerOffCal.py:83 DEBUG - Completed powerOffCal verification tests - result:True
2006-03-28 19:18:26,820 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:27,834 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:27,842 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:28,811 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:28,816 SequenceStep.py:93 DEBUG - Starting powerOffTem prerequisite tests
2006-03-28 19:18:28,820 SequenceStep.py:95 DEBUG - Completed powerOffTem prerequisite tests - result:True
2006-03-28 19:18:28,825 PowerOffTem.py:52 INFO  - Powering off TEM 0 on PDU 1...
2006-03-28 19:18:29,792 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:29,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:29,793 LIM.py:260 DEBUG - 	Action        : 8
2006-03-28 19:18:29,799 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:29,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:29,800 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:29,804 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:29,804 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:29,805 LIM.py:260 DEBUG - 	Action        : 5
2006-03-28 19:18:29,810 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:29,811 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:29,812 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:29,849 PowerOffTem.py:61 INFO  - Verified power off action.
2006-03-28 19:18:29,850 PowerOffTem.py:63 INFO  - Waiting 5 seconds for the TEM 0 3.3V voltage to settle...
2006-03-28 19:18:34,851 PowerOffTem.py:69 INFO  - Completed power off action for TEM 0, result:True
2006-03-28 19:18:34,852 PowerOffTem.py:76 DEBUG - Starting powerOffTem verification tests
2006-03-28 19:18:36,808 SequenceStep.py:585 INFO  - TEM 0 3.3V voltage measured as 1.14V and within the required range of [0.0, 2.0]
2006-03-28 19:18:36,809 PowerOffTem.py:85 DEBUG - Completed powerOffTem verification tests - result:True
2006-03-28 19:18:36,809 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:37,824 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:37,833 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:38,800 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:38,805 SequenceStep.py:93 DEBUG - Starting powerOffEpu prerequisite tests
2006-03-28 19:18:38,810 SequenceStep.py:95 DEBUG - Completed powerOffEpu prerequisite tests - result:True
2006-03-28 19:18:38,814 PowerOffEpu.py:52 INFO  - Powering off EPU 1...
2006-03-28 19:18:39,792 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:39,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:39,793 LIM.py:260 DEBUG - 	Action        : 8
2006-03-28 19:18:39,799 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:39,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:39,800 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:39,804 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:39,804 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:39,805 LIM.py:260 DEBUG - 	Action        : 5
2006-03-28 19:18:39,811 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:39,811 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:39,812 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:39,836 PowerOffEpu.py:61 INFO  - Verified power off action.
2006-03-28 19:18:39,837 PowerOffEpu.py:65 INFO  - Completed power off action for EPU 1, result:True
2006-03-28 19:18:39,838 PowerOffEpu.py:72 DEBUG - Starting powerOffEpu verification tests
2006-03-28 19:18:39,838 PowerSequenceStep.py:516 INFO  - Checking if EPU 1 voltage is within range [0.0, 0.5]...
2006-03-28 19:18:41,795 SequenceStep.py:585 INFO  - PDU 1 EPU 1 3.3V voltage measured as 0.08V and within the required range of [0.0, 0.5]
2006-03-28 19:18:41,795 PowerOffEpu.py:81 DEBUG - Completed powerOffEpu verification tests - result:True
2006-03-28 19:18:41,796 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:42,810 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:42,811 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002
2006-03-28 19:18:43,835 SequenceStep.py:454 INFO  - Configured LHK with file id 0x23400002
2006-03-28 19:18:43,844 SequenceStep.py:93 DEBUG - Starting powerOffEpu prerequisite tests
2006-03-28 19:18:43,849 SequenceStep.py:95 DEBUG - Completed powerOffEpu prerequisite tests - result:True
2006-03-28 19:18:43,849 PowerOffEpu.py:52 INFO  - Powering off EPU 0...
2006-03-28 19:18:44,793 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:44,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:44,794 LIM.py:260 DEBUG - 	Action        : 8
2006-03-28 19:18:44,799 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:44,800 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:44,801 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:44,804 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:44,805 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:44,805 LIM.py:260 DEBUG - 	Action        : 5
2006-03-28 19:18:44,811 LIM.py:261 DEBUG - 	Status        : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"')
2006-03-28 19:18:44,812 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:44,813 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:44,821 PowerOffEpu.py:61 INFO  - Verified power off action.
2006-03-28 19:18:44,822 PowerOffEpu.py:65 INFO  - Completed power off action for EPU 0, result:True
2006-03-28 19:18:44,823 PowerOffEpu.py:72 DEBUG - Starting powerOffEpu verification tests
2006-03-28 19:18:44,823 PowerSequenceStep.py:516 INFO  - Checking if EPU 0 voltage is within range [0.0, 0.5]...
2006-03-28 19:18:46,828 SequenceStep.py:585 INFO  - PDU 1 EPU 0 3.3V voltage measured as 0.08V and within the required range of [0.0, 0.5]
2006-03-28 19:18:46,829 PowerOffEpu.py:81 DEBUG - Completed powerOffEpu verification tests - result:True
2006-03-28 19:18:46,830 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration
2006-03-28 19:18:47,793 SequenceStep.py:467 INFO  - Configured LHK with the default configuration
2006-03-28 19:18:47,803 SequenceStep.py:93 DEBUG - Starting powerOffGasuPdu prerequisite tests
2006-03-28 19:18:47,807 SequenceStep.py:95 DEBUG - Completed powerOffGasuPdu prerequisite tests - result:True
2006-03-28 19:18:47,808 PowerOffGasuPdu.py:52 INFO  - Sending Load Shed to power off the GASU and the PDU
2006-03-28 19:18:48,792 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:48,793 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:48,793 LIM.py:260 DEBUG - 	Action        : 16
2006-03-28 19:18:48,796 LIM.py:261 DEBUG - 	Status        : 0x598cf25c - ('LIM_PKTSENT', '"Command or telemetry packet was sent to another task"')
2006-03-28 19:18:48,796 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:48,797 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:18:53,795 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:18:53,796 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:18:53,796 LIM.py:260 DEBUG - 	Action        : 9
2006-03-28 19:18:53,798 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:18:53,799 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:18:53,799 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:19:04,603 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:19:04,604 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:19:04,604 LIM.py:260 DEBUG - 	Action        : 10
2006-03-28 19:19:04,606 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:19:04,607 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:19:04,607 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:19:04,611 LIM.py:258 DEBUG - LIM State:
2006-03-28 19:19:04,611 LIM.py:259 DEBUG - 	Operating Mode: 1
2006-03-28 19:19:04,612 LIM.py:260 DEBUG - 	Action        : 17
2006-03-28 19:19:04,614 LIM.py:261 DEBUG - 	Status        : 0x598333a8 - ('LIM_SUCCESS', '"Success"')
2006-03-28 19:19:04,614 LIM.py:263 DEBUG - 	SaaTransit    : 0
2006-03-28 19:19:04,615 LIM.py:264 DEBUG - 	HV Allow      : 0
2006-03-28 19:19:07,808 PowerOffGasuPdu.py:60 INFO  - Verified completion of power off due to a Load-Shed command.
2006-03-28 19:19:07,809 PowerOffGasuPdu.py:64 INFO  - Completed Load-Shed action, result:True
2006-03-28 19:19:07,810 SequenceStep.py:104 DEBUG - Starting powerOffGasuPdu verification tests
2006-03-28 19:19:07,810 SequenceStep.py:106 DEBUG - Completed powerOffGasuPdu verification tests - result:True
2006-03-28 19:19:07,811 SequenceStep.py:93 DEBUG - Starting powerConsumption prerequisite tests
2006-03-28 19:19:07,812 SequenceStep.py:95 DEBUG - Completed powerConsumption prerequisite tests - result:True
2006-03-28 19:19:07,813 PowerConsumption.py:85 DEBUG - Starting powerConsumption verification tests
2006-03-28 19:19:08,378 SequenceStep.py:585 INFO  - LAT input power measured as 7.31W and within the required range of [0, 750]
2006-03-28 19:19:08,379 SequenceStep.py:567 INFO  - Waiting for operator acknowledgement: Enter dwell period for Power Consumption measurements:
2006-03-28 19:39:52,985 SequenceStep.py:573 INFO  - Operator confirmed the successful completion of manual task
2006-03-28 19:39:52,985 PowerConsumption.py:72 INFO  - Dwelling on the power rack for 10 seconds...
2006-03-28 19:40:02,986 SequenceStep.py:585 INFO  - LAT average input power measured as 11.02W and within the required range of [0, 650]
2006-03-28 19:40:02,987 PowerConsumption.py:109 DEBUG - Completed powerConsumption verification tests - result:True
2006-03-28 19:40:02,988 seAppBase.py:427 DEBUG - seAppBase.seStopRun -- LatPowerOff
2006-03-28 19:40:03,050 seAppBase.py:951 DEBUG - Generating run report...
2006-03-28 19:40:03,056 rcReportGen.py:95 DEBUG - Database elogbook opened successfully
2006-03-28 19:40:03,057 gVersions.py:83 INFO  - Retrieving FSW module versions from unit SIU...
2006-03-28 19:40:08,060 gVersions.py:92 INFO  - FSW module dump complete.
2006-03-28 19:40:08,394 seAppBase.py:1080 DEBUG - Run report generation complete.
2006-03-28 19:40:08,394 seAppBase.py:1201 INFO  - seAppBase.seStopRun -- Test LatPowerOff finished, Run Id: 101000056, Status: PASSED, Completion Time: Tue Mar 28 19:40:03 2006