2006-03-06 19:17:34,665 seAppBase.py:384 INFO - seAppBase.seStartRun -- Test LatPowerOff starting run, Operator: NOT-DEFINED, Run Id: 101000045, Time Started: 060306191734 -- Mon Mar 6 19:17:34 2006 2006-03-06 19:17:34,667 seAppBase.py:400 DEBUG - seAppBase.seStartRun -- LatPowerOff 2006-03-06 19:17:34,672 LatPowerOff.py:327 DEBUG - LatPowerOff.startRun() 2006-03-06 19:17:34,675 SequenceStep.py:93 DEBUG - Starting dwellOnStatus prerequisite tests 2006-03-06 19:17:34,677 SequenceStep.py:95 DEBUG - Completed dwellOnStatus prerequisite tests - result:True 2006-03-06 19:17:34,677 DwellOnStatus.py:101 INFO - Dwelling on the LAT for 30 seconds... 2006-03-06 19:18:04,682 DwellOnStatus.py:230 DEBUG - Starting dwellOnStatus verification tests 2006-03-06 19:18:04,683 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-1.000, 10.000] for payload LHKAFR33ISUM, values [0.00, 0.00, 0.00, 0.00] (starting with index:0, margin:0) 2006-03-06 19:18:04,684 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKAFR33ISUM are within [-1.000, 10.000] 2006-03-06 19:18:04,685 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VA, values [3.38, 3.38, 3.38] (starting with index:0, margin:0) 2006-03-06 19:18:04,685 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CAL33VA are within [3.000, 3.500] 2006-03-06 19:18:04,686 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV0, values [0.25, 0.25, 0.31] (starting with index:0, margin:0) 2006-03-06 19:18:04,687 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CALBSV0 are within [0.000, 80.000] 2006-03-06 19:18:04,688 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 80.000] for payload LHKT0CALBSV1, values [25.28, 25.40, 25.34] (starting with index:0, margin:0) 2006-03-06 19:18:04,688 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CALBSV1 are within [0.000, 80.000] 2006-03-06 19:18:04,689 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-120.000, 30.000] for payload LHKAEMFR0T, values [23.73, 23.73, 23.73, 23.73] (starting with index:0, margin:0) 2006-03-06 19:18:04,690 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKAEMFR0T are within [-120.000, 30.000] 2006-03-06 19:18:04,691 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC1T0, values [27.70, 27.66, 27.70] (starting with index:0, margin:0) 2006-03-06 19:18:04,691 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC1T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,692 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [23.000, 40.000] for payload LHKT0CALAF1T1, values [27.77, 27.77, 27.77] (starting with index:0, margin:0) 2006-03-06 19:18:04,693 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CALAF1T1 are within [23.000, 40.000] 2006-03-06 19:18:04,694 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC0T1, values [-114.72, -114.72, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,694 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC0T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,695 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP0EPU0T, values [26.85, 26.88, 26.88, 26.92] (starting with index:0, margin:0) 2006-03-06 19:18:04,696 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0EPU0T are within [-30.000, 45.000] 2006-03-06 19:18:04,697 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 6.000] for payload L_DAQ_P_SIU_V, values [2.34, 2.32, 2.38, 2.34, 2.35, 2.34, 2.34, 2.36, 2.34, 2.38, 2.38, 2.34, 2.34, 2.42, 2.34, 2.35, 2.35, 2.34, 2.34, 2.36, 2.42, 2.34, 2.34, 2.34, 2.40, 2.40, 2.33, 2.34, 2.33, 2.35] (starting with index:0, margin:0) 2006-03-06 19:18:04,698 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_SIU_V are within [0.000, 6.000] 2006-03-06 19:18:04,699 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC6T0, values [26.68, 26.68, 26.68] (starting with index:0, margin:0) 2006-03-06 19:18:04,699 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC6T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,700 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [23.000, 50.000] for payload L_DAQ_P_SIU_T, values [31.59, 33.09, 32.91, 33.09, 33.00, 32.64, 31.59, 32.73, 33.36, 33.09, 33.09, 33.09, 33.18, 33.18, 31.24, 34.19, 32.64, 33.82, 33.09, 31.50, 33.00, 33.18, 33.00, 31.59, 33.00, 33.00, 33.18, 31.59, 33.00, 31.59] (starting with index:0, margin:0) 2006-03-06 19:18:04,702 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_SIU_T are within [23.000, 50.000] 2006-03-06 19:18:04,702 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [23.000, 40.000] for payload LHKT0CALAF0T1, values [27.77, 27.80, 27.80] (starting with index:0, margin:0) 2006-03-06 19:18:04,703 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CALAF0T1 are within [23.000, 40.000] 2006-03-06 19:18:04,704 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC3T0, values [30.21, 30.21, 30.25] (starting with index:0, margin:0) 2006-03-06 19:18:04,704 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC3T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,705 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-40.000, 60.000] for payload LHKP0TEM0PST, values [23.19, 23.19, 23.19, 23.22] (starting with index:0, margin:0) 2006-03-06 19:18:04,706 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0TEM0PST are within [-40.000, 60.000] 2006-03-06 19:18:04,707 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VD, values [2.52, 2.52, 2.52] (starting with index:0, margin:0) 2006-03-06 19:18:04,708 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKR25VD are within [0.000, 3.000] 2006-03-06 19:18:04,708 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC7T0, values [27.34, 27.38, 27.38] (starting with index:0, margin:0) 2006-03-06 19:18:04,709 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC7T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,710 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC7T1, values [-114.72, -114.72, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,711 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC7T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,711 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [23.000, 40.000] for payload LHKT0CALAF2T1, values [26.54, 26.47, 26.47] (starting with index:0, margin:0) 2006-03-06 19:18:04,712 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CALAF2T1 are within [23.000, 40.000] 2006-03-06 19:18:04,713 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [23.000, 40.000] for payload LHKT0CALAF3T1, values [25.62, 25.62, 25.59] (starting with index:0, margin:0) 2006-03-06 19:18:04,714 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CALAF3T1 are within [23.000, 40.000] 2006-03-06 19:18:04,714 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC4T1, values [-114.72, -114.72, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,715 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC4T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,716 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC2T0, values [28.60, 28.60, 28.60] (starting with index:0, margin:0) 2006-03-06 19:18:04,717 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC2T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,717 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC4T0, values [27.59, 27.59, 27.52] (starting with index:0, margin:0) 2006-03-06 19:18:04,718 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC4T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,719 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKEPU1CPUJTEMP, values [39.00, 39.00, 39.00] (starting with index:0, margin:0) 2006-03-06 19:18:04,720 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKEPU1CPUJTEMP are within [1.000, 999.000] 2006-03-06 19:18:04,720 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP0EPU1PM, values [1.00, 1.00, 1.00, 1.00] (starting with index:0, margin:0) 2006-03-06 19:18:04,721 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0EPU1PM are within [1.000, 1.000] 2006-03-06 19:18:04,722 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [23.000, 30.000] for payload L_DAQ_P_GASU_T, values [25.41, 24.36, 25.34, 24.78, 24.78, 25.06, 24.78, 24.85, 24.22, 24.50, 24.50, 24.85, 25.06, 24.78, 24.78, 25.41, 24.85, 25.06, 25.06, 24.50, 24.85, 24.50, 25.41, 24.78, 24.50, 24.22, 25.41, 24.85, 24.85, 25.34] (starting with index:0, margin:0) 2006-03-06 19:18:04,723 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_GASU_T are within [23.000, 30.000] 2006-03-06 19:18:04,724 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [666.000, 814.000] for payload LHKAEMFR0V1, values [773.43, 773.43, 773.43, 773.43] (starting with index:0, margin:0) 2006-03-06 19:18:04,725 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKAEMFR0V1 are within [666.000, 814.000] 2006-03-06 19:18:04,726 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC6T1, values [-114.72, -114.72, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,726 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC6T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,727 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC2T1, values [-114.72, -114.72, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,728 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC2T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,729 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [2.000, 3.500] for payload LHKP0EPU033V, values [2.25, 2.25, 2.25, 2.25] (starting with index:0, margin:0) 2006-03-06 19:18:04,729 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0EPU033V are within [2.000, 3.500] 2006-03-06 19:18:04,730 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_EBM33V, values [3.35, 3.32, 3.34, 3.35, 3.28, 3.29, 3.35, 3.35, 3.28, 3.32, 3.35, 3.28, 3.35, 3.34, 3.34, 3.33, 3.32, 3.36, 3.35, 3.29, 3.38, 3.32, 3.34, 3.27, 3.28, 3.35, 3.34, 3.34, 3.31, 3.35] (starting with index:0, margin:0) 2006-03-06 19:18:04,731 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_EBM33V are within [3.000, 3.600] 2006-03-06 19:18:04,732 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_DAQ_V, values [27.78, 27.93, 27.73, 27.93, 27.73, 28.17, 27.93, 28.08, 27.73, 28.12, 27.69, 27.73, 28.03, 27.93, 27.78, 27.93, 28.08, 27.98, 28.03, 28.03, 28.03, 28.08, 28.27, 27.73, 28.08, 28.08, 27.73, 27.93, 28.08, 27.93] (starting with index:0, margin:0) 2006-03-06 19:18:04,734 SequenceStep.py:539 INFO - Dwell telemetry for payload VSC_RBPU_DAQ_V are within [27.000, 29.000] 2006-03-06 19:18:04,734 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC3T1, values [-114.72, -114.72, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,735 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC3T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,736 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-40.000, 60.000] for payload LHKP0TEM0PCT, values [26.37, 26.37, 26.37, 26.41] (starting with index:0, margin:0) 2006-03-06 19:18:04,737 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0TEM0PCT are within [-40.000, 60.000] 2006-03-06 19:18:04,737 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0CAL33VD, values [3.36, 3.36, 3.36] (starting with index:0, margin:0) 2006-03-06 19:18:04,738 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0CAL33VD are within [3.000, 3.500] 2006-03-06 19:18:04,739 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 29.000] for payload LHKAEMFR0VD, values [3.48, 3.48, 3.48, 3.48] (starting with index:0, margin:0) 2006-03-06 19:18:04,740 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKAEMFR0VD are within [0.000, 29.000] 2006-03-06 19:18:04,740 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 6.000] for payload L_DAQ_P_PDU_V, values [3.36, 3.36, 3.36, 3.36, 3.32, 3.36, 3.37, 3.35, 3.33, 3.40, 3.35, 3.36, 3.36, 3.35, 3.32, 3.39, 3.33, 3.36, 3.38, 3.37, 3.39, 3.36, 3.35, 3.32, 3.36, 3.36, 3.32, 3.36, 3.36, 3.36] (starting with index:0, margin:0) 2006-03-06 19:18:04,742 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_PDU_V are within [0.000, 6.000] 2006-03-06 19:18:04,742 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [1.000, 1.000] for payload LHKP0EPU0PM, values [1.00, 1.00, 1.00, 1.00] (starting with index:0, margin:0) 2006-03-06 19:18:04,743 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0EPU0PM are within [1.000, 1.000] 2006-03-06 19:18:04,744 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [2.000, 3.500] for payload LHKP0EPU133V, values [2.26, 2.26, 2.26, 2.26] (starting with index:0, margin:0) 2006-03-06 19:18:04,745 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0EPU133V are within [2.000, 3.500] 2006-03-06 19:18:04,745 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC1T1, values [-108.07, -108.07, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,746 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC1T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,747 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-30.000, 45.000] for payload LHKP0EPU1T, values [25.51, 25.51, 25.55, 25.51] (starting with index:0, margin:0) 2006-03-06 19:18:04,748 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKP0EPU1T are within [-30.000, 45.000] 2006-03-06 19:18:04,748 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_EBM25V, values [2.48, 2.46, 2.53, 2.50, 2.50, 2.51, 2.43, 2.48, 2.46, 2.44, 2.46, 2.50, 2.43, 2.46, 2.43, 2.42, 2.49, 2.50, 2.43, 2.48, 2.48, 2.49, 2.53, 2.53, 2.46, 2.44, 2.42, 2.43, 2.50, 2.44] (starting with index:0, margin:0) 2006-03-06 19:18:04,750 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_EBM25V are within [2.000, 2.600] 2006-03-06 19:18:04,751 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [2.000, 2.600] for payload L_DAQ_P_GEM25V, values [2.49, 2.46, 2.46, 2.47, 2.45, 2.46, 2.45, 2.48, 2.44, 2.48, 2.48, 2.48, 2.48, 2.50, 2.52, 2.46, 2.46, 2.49, 2.50, 2.46, 2.49, 2.45, 2.46, 2.48, 2.46, 2.47, 2.47, 2.46, 2.45, 2.48] (starting with index:0, margin:0) 2006-03-06 19:18:04,752 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_GEM25V are within [2.000, 2.600] 2006-03-06 19:18:04,753 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [3.000, 3.600] for payload L_DAQ_P_GEM33V, values [3.35, 3.28, 3.30, 3.26, 3.28, 3.30, 3.28, 3.28, 3.33, 3.29, 3.28, 3.34, 3.32, 3.29, 3.32, 3.32, 3.32, 3.30, 3.27, 3.29, 3.33, 3.32, 3.28, 3.30, 3.28, 3.35, 3.32, 3.31, 3.34, 3.32] (starting with index:0, margin:0) 2006-03-06 19:18:04,754 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_GEM33V are within [3.000, 3.600] 2006-03-06 19:18:04,755 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [3.000, 3.500] for payload LHKT0TEM33V, values [3.40, 3.40, 3.40] (starting with index:0, margin:0) 2006-03-06 19:18:04,756 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TEM33V are within [3.000, 3.500] 2006-03-06 19:18:04,757 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-1.000, 20.000] for payload VSC_RBPU_DAQ_C, values [2.73, 2.54, 2.34, 2.69, 2.29, 2.44, 2.69, 2.34, 2.54, 2.39, 2.59, 2.64, 2.39, 2.34, 2.29, 2.49, 2.44, 2.34, 2.29, 2.10, 2.00, 2.34, 2.34, 2.54, 2.34, 2.34, 2.54, 2.69, 2.29, 2.78] (starting with index:0, margin:0) 2006-03-06 19:18:04,758 SequenceStep.py:539 INFO - Dwell telemetry for payload VSC_RBPU_DAQ_C are within [-1.000, 20.000] 2006-03-06 19:18:04,759 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 100.000] for payload LHKT0TKRBV1, values [25.77, 25.84, 25.77] (starting with index:0, margin:0) 2006-03-06 19:18:04,759 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRBV1 are within [0.000, 100.000] 2006-03-06 19:18:04,763 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 100.000] for payload LHKT0TKRBV0, values [0.31, 0.31, 0.31] (starting with index:0, margin:0) 2006-03-06 19:18:04,764 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRBV0 are within [0.000, 100.000] 2006-03-06 19:18:04,765 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 2.000] for payload LHKT0TKR15VAA, values [1.43, 1.43, 1.43] (starting with index:0, margin:0) 2006-03-06 19:18:04,766 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKR15VAA are within [0.000, 2.000] 2006-03-06 19:18:04,770 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-1.000, 20.000] for payload VSC_RBPU_SIU_C, values [0.71, 0.69, 0.70, 0.72, 0.71, 0.68, 0.70, 0.70, 0.66, 0.72, 0.72, 0.71, 0.70, 0.70, 0.67, 0.74, 0.70, 0.70, 0.70, 0.73, 0.73, 0.70, 0.70, 0.72, 0.71, 0.70, 0.70, 0.72, 0.70, 0.70] (starting with index:0, margin:0) 2006-03-06 19:18:04,772 SequenceStep.py:539 INFO - Dwell telemetry for payload VSC_RBPU_SIU_C are within [-1.000, 20.000] 2006-03-06 19:18:04,773 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V0, values [27.54, 27.55, 27.54] (starting with index:0, margin:0) 2006-03-06 19:18:04,774 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TEM28V0 are within [27.000, 29.000] 2006-03-06 19:18:04,775 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [23.000, 50.000] for payload L_DAQ_P_PDU_T, values [23.20, 23.27, 23.13, 23.40, 23.27, 23.67, 23.74, 24.01, 24.36, 24.01, 24.29, 23.74, 23.47, 23.61, 23.20, 24.01, 23.27, 23.74, 23.74, 24.15, 23.13, 24.29, 24.29, 23.27, 23.47, 23.74, 24.29, 23.74, 23.81, 23.74] (starting with index:0, margin:0) 2006-03-06 19:18:04,777 SequenceStep.py:539 INFO - Dwell telemetry for payload L_DAQ_P_PDU_T are within [23.000, 50.000] 2006-03-06 19:18:04,779 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC0T0, values [28.20, 28.20, 28.20] (starting with index:0, margin:0) 2006-03-06 19:18:04,780 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC0T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,781 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC5T0, values [28.86, 28.89, 28.89] (starting with index:0, margin:0) 2006-03-06 19:18:04,782 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC5T0 are within [-123.000, 40.000] 2006-03-06 19:18:04,812 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [-123.000, 40.000] for payload LHKT0TKRC5T1, values [-114.72, -114.72, -114.72] (starting with index:0, margin:0) 2006-03-06 19:18:04,813 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKRC5T1 are within [-123.000, 40.000] 2006-03-06 19:18:04,813 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [0.000, 3.000] for payload LHKT0TKR25VAB, values [2.56, 2.56, 2.56] (starting with index:0, margin:0) 2006-03-06 19:18:04,814 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TKR25VAB are within [0.000, 3.000] 2006-03-06 19:18:04,815 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [27.000, 29.000] for payload LHKT0TEM28V1, values [27.77, 27.78, 27.77] (starting with index:0, margin:0) 2006-03-06 19:18:04,816 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKT0TEM28V1 are within [27.000, 29.000] 2006-03-06 19:18:04,816 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [1.000, 999.000] for payload LHKEPU0CPUJTEMP, values [43.00, 43.00, 43.00] (starting with index:0, margin:0) 2006-03-06 19:18:04,817 SequenceStep.py:539 INFO - Dwell telemetry for payload LHKEPU0CPUJTEMP are within [1.000, 999.000] 2006-03-06 19:18:04,818 SequenceStep.py:539 INFO - Checking if dwell telemetry is in range [27.000, 29.000] for payload VSC_RBPU_SIU_V, values [28.08, 28.12, 28.47, 27.93, 28.08, 28.17, 28.12, 28.12, 28.37, 28.12, 28.12, 28.12, 28.47, 28.17, 28.12, 27.93, 28.12, 27.98, 27.93, 28.12, 28.03, 28.12, 28.03, 28.27, 28.08, 28.27, 27.98, 28.12, 28.03, 28.08] (starting with index:0, margin:0) 2006-03-06 19:18:04,819 SequenceStep.py:539 INFO - Dwell telemetry for payload VSC_RBPU_SIU_V are within [27.000, 29.000] 2006-03-06 19:18:04,820 DwellOnStatus.py:232 DEBUG - Completed dwellOnStatus verification tests - result:True 2006-03-06 19:18:04,820 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:18:05,383 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:18:05,385 SequenceStep.py:93 DEBUG - Starting powerOffAcdHvbs prerequisite tests 2006-03-06 19:18:05,386 SequenceStep.py:95 DEBUG - Completed powerOffAcdHvbs prerequisite tests - result:True 2006-03-06 19:18:05,387 PowerOffAcdHvbs.py:79 INFO - Configuring the ACD bias voltage for free board 0 with the SAA level of 945 counts and operational level of 0 counts... 2006-03-06 19:18:06,374 LIM.py:226 DEBUG - LIM State: 1 56 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:06,409 PowerOffAcdHvbs.py:95 INFO - Stepping down to SAA voltage... 2006-03-06 19:18:07,370 LIM.py:226 DEBUG - LIM State: 1 60 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:07,375 LIM.py:226 DEBUG - LIM State: 1 19 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:12,425 PowerOffAcdHvbs.py:103 INFO - Verified that ACD bias voltages are configured. 2006-03-06 19:18:12,425 PowerOffAcdHvbs.py:108 INFO - Verified HV State Change. 2006-03-06 19:18:12,426 PowerOffAcdHvbs.py:114 INFO - Stepping down to minimum voltage... 2006-03-06 19:18:13,370 LIM.py:226 DEBUG - LIM State: 1 60 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:13,375 LIM.py:226 DEBUG - LIM State: 1 21 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:18,390 PowerOffAcdHvbs.py:122 INFO - Verified HV State Change. 2006-03-06 19:18:18,390 PowerOffAcdHvbs.py:131 INFO - Configuring the ACD bias voltage for free board 0 with the SAA level of 0 counts and operational level of 0 counts... 2006-03-06 19:18:19,374 LIM.py:226 DEBUG - LIM State: 1 56 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:19,413 PowerOffAcdHvbs.py:140 INFO - Disallowing HV voltage... 2006-03-06 19:18:20,370 LIM.py:226 DEBUG - LIM State: 1 60 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:20,375 LIM.py:226 DEBUG - LIM State: 1 19 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:20,427 PowerOffAcdHvbs.py:147 INFO - Verified that ACD bias voltages are configured. 2006-03-06 19:18:20,427 PowerOffAcdHvbs.py:152 INFO - Verified HV State Change. 2006-03-06 19:18:20,428 PowerOffAcdHvbs.py:156 INFO - Completed Set ACD Bias Voltage to Minimum action for free board 0, result:True 2006-03-06 19:18:20,428 PowerOffAcdHvbs.py:163 DEBUG - Starting powerOffAcdHvbs verification tests 2006-03-06 19:18:20,429 PowerSequenceStep.py:1730 INFO - Executing LIM SAA enter command 2006-03-06 19:18:21,370 LIM.py:226 DEBUG - LIM State: 1 45 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:21,375 LIM.py:226 DEBUG - LIM State: 1 19 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:21,393 PowerSequenceStep.py:1737 INFO - Verified SAA entry. 2006-03-06 19:18:26,393 PowerSequenceStep.py:923 INFO - Checking if AEM free board 0 HV1 voltage is within range [-60.0, 60.0]... 2006-03-06 19:18:28,393 SequenceStep.py:539 INFO - AEM free board 0 HV1 voltage measured as 10.13V and within the required range of [-60.0, 60.0] 2006-03-06 19:18:28,394 PowerSequenceStep.py:1755 INFO - Configuring LIM to allow setting of the HV 2006-03-06 19:18:29,370 LIM.py:226 DEBUG - LIM State: 1 60 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:29,408 PowerSequenceStep.py:1762 INFO - Verified HV State Change. 2006-03-06 19:18:29,409 PowerSequenceStep.py:1769 INFO - Executing LIM SAA exit command 2006-03-06 19:18:30,370 LIM.py:226 DEBUG - LIM State: 1 45 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:30,375 LIM.py:226 DEBUG - LIM State: 1 21 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:30,425 PowerSequenceStep.py:1776 INFO - Verified SAA exit. 2006-03-06 19:18:35,426 PowerSequenceStep.py:1785 INFO - Configuring LIM to disallow setting of the HV 2006-03-06 19:18:36,370 LIM.py:226 DEBUG - LIM State: 1 60 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:36,375 LIM.py:226 DEBUG - LIM State: 1 19 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:18:36,390 PowerSequenceStep.py:1792 INFO - Verified HV State Change. 2006-03-06 19:18:36,390 PowerSequenceStep.py:923 INFO - Checking if AEM free board 0 HV1 voltage is within range [-60.0, 60.0]... 2006-03-06 19:18:38,389 SequenceStep.py:539 INFO - AEM free board 0 HV1 voltage measured as 10.13V and within the required range of [-60.0, 60.0] 2006-03-06 19:18:38,390 PowerOffAcdHvbs.py:186 DEBUG - Completed powerOffAcdHvbs verification tests - result:True 2006-03-06 19:18:38,390 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:18:39,404 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:18:39,405 PowerOffAcdFreeBoard.py:52 DEBUG - Starting powerOffAcdFreeBoard prerequisite tests 2006-03-06 19:18:39,406 PowerSequenceStep.py:923 INFO - Checking if AEM free board 0 HV1 voltage is within range [-0.5, 80.0]... 2006-03-06 19:18:41,407 SequenceStep.py:539 INFO - AEM free board 0 HV1 voltage measured as 10.13V and within the required range of [-0.5, 80.0] 2006-03-06 19:18:41,408 PowerOffAcdFreeBoard.py:64 DEBUG - Completed powerOffAcdFreeBoard prerequisite tests - result:True 2006-03-06 19:18:41,409 PowerOffAcdFreeBoard.py:74 INFO - Powering off free board 0... 2006-03-06 19:18:42,374 LIM.py:226 DEBUG - LIM State: 1 8 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:42,382 LIM.py:226 DEBUG - LIM State: 1 5 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:42,416 PowerOffAcdFreeBoard.py:84 INFO - Verified power off action. 2006-03-06 19:18:42,417 PowerOffAcdFreeBoard.py:88 INFO - Completed ACD power off action for free board 0, result:True 2006-03-06 19:18:42,418 PowerOffAcdFreeBoard.py:95 DEBUG - Starting powerOffAcdFreeBoard verification tests 2006-03-06 19:18:42,418 PowerSequenceStep.py:778 INFO - Checking if the AEM/EBM 3.3V and AEM/EBM 2.5V voltages are within range [[3.0, 3.6000000000000001], [2.0, 2.6000000000000001]]... 2006-03-06 19:18:42,984 SequenceStep.py:539 INFO - AEM/EBM 3.3V voltage 3.34V is within [3.0, 3.6000000000000001] 2006-03-06 19:18:42,984 SequenceStep.py:539 INFO - AEM/EBM 2.5V voltage 2.42V is within [2.0, 2.6000000000000001] 2006-03-06 19:18:42,985 PowerSequenceStep.py:877 INFO - Checking if AEM free board 0 voltage is within range [0.0, 29.0]... 2006-03-06 19:18:45,386 SequenceStep.py:539 INFO - AEM free board 0 voltage measured as 0.73V and within the required range of [0.0, 29.0] 2006-03-06 19:18:45,386 PowerOffAcdFreeBoard.py:110 DEBUG - Completed powerOffAcdFreeBoard verification tests - result:True 2006-03-06 19:18:45,387 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:18:46,401 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:18:46,402 PowerOffAem.py:51 DEBUG - Starting powerOffAem prerequisite tests 2006-03-06 19:18:46,403 PowerSequenceStep.py:877 INFO - Checking if AEM free board 0 voltage is within range [-0.10000000000000001, 0.80000000000000004]... 2006-03-06 19:18:48,403 SequenceStep.py:539 INFO - AEM free board 0 voltage measured as 0.73V and within the required range of [-0.10000000000000001, 0.80000000000000004] 2006-03-06 19:18:48,403 PowerOffAem.py:62 DEBUG - Completed powerOffAem prerequisite tests - result:True 2006-03-06 19:18:48,404 PowerOffAem.py:72 INFO - Powering off the AEM... 2006-03-06 19:18:49,374 LIM.py:226 DEBUG - LIM State: 1 8 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:49,383 LIM.py:226 DEBUG - LIM State: 1 5 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:50,426 PowerOffAem.py:82 INFO - Verified power off action. 2006-03-06 19:18:50,426 PowerOffAem.py:86 INFO - Completed AEM power off action, result:True 2006-03-06 19:18:50,427 PowerOffAem.py:93 DEBUG - Starting powerOffAem verification tests 2006-03-06 19:18:50,428 PowerOffAem.py:101 DEBUG - Completed powerOffAem verification tests - result:True 2006-03-06 19:18:50,428 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:18:51,392 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:18:51,393 SequenceStep.py:93 DEBUG - Starting powerOffTkrHvbs prerequisite tests 2006-03-06 19:18:51,394 SequenceStep.py:95 DEBUG - Completed powerOffTkrHvbs prerequisite tests - result:True 2006-03-06 19:18:51,394 PowerOffTkrHvbs.py:50 INFO - Setting TEM 0 TKR bias voltage to 0x0... 2006-03-06 19:18:52,374 LIM.py:226 DEBUG - LIM State: 1 58 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:52,415 PowerOffTkrHvbs.py:59 INFO - Verified TKR bias voltage change. 2006-03-06 19:18:52,415 PowerOffTkrHvbs.py:63 INFO - Completed Set TKR bias voltage to minumum action for TKR 0, result:True 2006-03-06 19:18:52,416 PowerOffTkrHvbs.py:70 DEBUG - Starting powerOffTkrHvbs verification tests 2006-03-06 19:18:52,417 PowerSequenceStep.py:1491 INFO - Checking if TEM 0 TKR bias voltages are within range [[0.0, 100.0], [0.0, 100.0], [-1.0, 10.0]]... 2006-03-06 19:18:54,415 SequenceStep.py:539 INFO - TEM 0 TKR bias V0 measured as 0.31V and within the required range of [0.0, 100.0] 2006-03-06 19:18:54,416 SequenceStep.py:539 INFO - TEM 0 TKR bias V1 measured as 25.90V and within the required range of [0.0, 100.0] 2006-03-06 19:18:54,417 SequenceStep.py:556 WARNING - Conversion constant for LDET0TKRBIASI was not in the database, using the data from the configuration file 2006-03-06 19:18:54,418 SequenceStep.py:539 INFO - TEM 0 TKR bias current measured as -0.00A and within the required range of [-1.0, 10.0] 2006-03-06 19:18:54,419 PowerOffTkrHvbs.py:83 DEBUG - Completed powerOffTkrHvbs verification tests - result:True 2006-03-06 19:18:54,419 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:18:55,383 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:18:55,385 SequenceStep.py:93 DEBUG - Starting powerOffTkr prerequisite tests 2006-03-06 19:18:55,385 SequenceStep.py:95 DEBUG - Completed powerOffTkr prerequisite tests - result:True 2006-03-06 19:18:55,386 PowerOffTkr.py:51 INFO - Powering off TEM 0 TKR... 2006-03-06 19:18:56,374 LIM.py:226 DEBUG - LIM State: 1 8 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:57,574 LIM.py:226 DEBUG - LIM State: 1 5 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:18:57,606 PowerOffTkr.py:61 INFO - Verified power off action. 2006-03-06 19:18:57,607 PowerOffTkr.py:65 INFO - Completed power off action for TKR 0, result:True 2006-03-06 19:18:57,608 PowerOffTkr.py:72 DEBUG - Starting powerOffTkr verification tests 2006-03-06 19:18:57,608 PowerSequenceStep.py:1402 INFO - Checking if TEM 0 TKR voltages are within range [[0.0, 0.10000000000000001], [0.0, 0.10000000000000001], [0.0, 0.10000000000000001]]... 2006-03-06 19:18:59,410 SequenceStep.py:539 INFO - TEM 0 TKR 1.5V analog measured as 0.00V and within the required range of [0.0, 0.10000000000000001] 2006-03-06 19:18:59,411 SequenceStep.py:539 INFO - TEM 0 TKR 2.5V digital measured as 0.00V and within the required range of [0.0, 0.10000000000000001] 2006-03-06 19:18:59,411 SequenceStep.py:539 INFO - TEM 0 TKR 2.5V analog measured as 0.01V and within the required range of [0.0, 0.10000000000000001] 2006-03-06 19:18:59,412 PowerOffTkr.py:86 DEBUG - Completed powerOffTkr verification tests - result:True 2006-03-06 19:18:59,412 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:19:00,376 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:19:00,377 SequenceStep.py:93 DEBUG - Starting powerOffCalHvbs prerequisite tests 2006-03-06 19:19:00,378 SequenceStep.py:95 DEBUG - Completed powerOffCalHvbs prerequisite tests - result:True 2006-03-06 19:19:00,378 PowerOffCalHvbs.py:50 INFO - Setting TEM 0 CAL bias voltage to 0x0... 2006-03-06 19:19:01,374 LIM.py:226 DEBUG - LIM State: 1 57 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:01,395 PowerOffCalHvbs.py:59 INFO - Verified CAL bias voltage change. 2006-03-06 19:19:01,395 PowerOffCalHvbs.py:63 INFO - Completed Set CAL bias voltage to minumum action for TKR 0, result:True 2006-03-06 19:19:01,396 PowerOffCalHvbs.py:70 DEBUG - Starting powerOffCalHvbs verification tests 2006-03-06 19:19:01,397 PowerSequenceStep.py:1253 INFO - Checking if TEM 0 CAL bias voltages are within range [[0.0, 80.0], [0.0, 80.0], [-1.0, 10.0]]... 2006-03-06 19:19:03,397 SequenceStep.py:539 INFO - TEM 0 CAL bias V0 measured as 0.25V and within the required range of [0.0, 80.0] 2006-03-06 19:19:03,398 SequenceStep.py:539 INFO - TEM 0 CAL bias V1 measured as 25.65V and within the required range of [0.0, 80.0] 2006-03-06 19:19:03,398 PowerSequenceStep.py:1312 WARNING - Conversion constant for LDET0CALBIASI was not in the database, using the data from the configuration file 2006-03-06 19:19:03,399 SequenceStep.py:539 INFO - TEM 0 CAL bias current measured as 0.01A and within the required range of [-1.0, 10.0] 2006-03-06 19:19:03,400 PowerOffCalHvbs.py:83 DEBUG - Completed powerOffCalHvbs verification tests - result:True 2006-03-06 19:19:03,400 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:19:04,415 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:19:04,416 SequenceStep.py:93 DEBUG - Starting powerOffCal prerequisite tests 2006-03-06 19:19:04,417 SequenceStep.py:95 DEBUG - Completed powerOffCal prerequisite tests - result:True 2006-03-06 19:19:04,417 PowerOffCal.py:51 INFO - Powering off TEM 0 CAL... 2006-03-06 19:19:05,374 LIM.py:226 DEBUG - LIM State: 1 8 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:06,574 LIM.py:226 DEBUG - LIM State: 1 5 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:06,589 PowerOffCal.py:61 INFO - Verified power off action. 2006-03-06 19:19:06,590 PowerOffCal.py:65 INFO - Completed power off action for CAL 0, result:True 2006-03-06 19:19:06,590 PowerOffCal.py:72 DEBUG - Starting powerOffCal verification tests 2006-03-06 19:19:06,591 PowerSequenceStep.py:1185 INFO - Checking if TEM 0 CAL 3.3V digital and analog are within range [[0.0, 0.10000000000000001], [0.0, 0.10000000000000001]]... 2006-03-06 19:19:08,387 SequenceStep.py:539 INFO - TEM 0 CAL 3.3V digital measured as 0.00V and within the required range of [0.0, 0.10000000000000001] 2006-03-06 19:19:08,388 SequenceStep.py:539 INFO - TEM 0 CAL 3.3V analog measured as 0.01V and within the required range of [0.0, 0.10000000000000001] 2006-03-06 19:19:08,389 PowerOffCal.py:83 DEBUG - Completed powerOffCal verification tests - result:True 2006-03-06 19:19:08,389 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:19:09,403 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:19:09,405 SequenceStep.py:93 DEBUG - Starting powerOffTem prerequisite tests 2006-03-06 19:19:09,405 SequenceStep.py:95 DEBUG - Completed powerOffTem prerequisite tests - result:True 2006-03-06 19:19:09,406 PowerOffTem.py:52 INFO - Powering off TEM 0 on PDU 0... 2006-03-06 19:19:10,374 LIM.py:226 DEBUG - LIM State: 1 8 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:10,383 LIM.py:226 DEBUG - LIM State: 1 5 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:10,433 PowerOffTem.py:61 INFO - Verified power off action. 2006-03-06 19:19:10,434 PowerOffTem.py:63 INFO - Waiting 5 seconds for the TEM 0 3.3V voltage to settle... 2006-03-06 19:19:15,435 PowerOffTem.py:69 INFO - Completed power off action for TEM 0, result:True 2006-03-06 19:19:15,435 PowerOffTem.py:76 DEBUG - Starting powerOffTem verification tests 2006-03-06 19:19:17,385 SequenceStep.py:539 INFO - TEM 0 3.3V voltage measured as 1.13V and within the required range of [0.0, 2.0] 2006-03-06 19:19:17,386 PowerOffTem.py:85 DEBUG - Completed powerOffTem verification tests - result:True 2006-03-06 19:19:17,386 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:19:18,400 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:19:18,401 SequenceStep.py:93 DEBUG - Starting powerOffEpu prerequisite tests 2006-03-06 19:19:18,402 SequenceStep.py:95 DEBUG - Completed powerOffEpu prerequisite tests - result:True 2006-03-06 19:19:18,403 PowerOffEpu.py:52 INFO - Powering off EPU 1... 2006-03-06 19:19:19,374 LIM.py:226 DEBUG - LIM State: 1 8 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:19,382 LIM.py:226 DEBUG - LIM State: 1 5 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:19,424 PowerOffEpu.py:61 INFO - Verified power off action. 2006-03-06 19:19:19,425 PowerOffEpu.py:65 INFO - Completed power off action for EPU 1, result:True 2006-03-06 19:19:19,425 PowerOffEpu.py:72 DEBUG - Starting powerOffEpu verification tests 2006-03-06 19:19:19,426 PowerSequenceStep.py:516 INFO - Checking if EPU 1 voltage is within range [0.0, 0.5]... 2006-03-06 19:19:21,377 SequenceStep.py:539 INFO - PDU 0 EPU 1 3.3V voltage measured as 0.20V and within the required range of [0.0, 0.5] 2006-03-06 19:19:21,378 PowerOffEpu.py:81 DEBUG - Completed powerOffEpu verification tests - result:True 2006-03-06 19:19:21,379 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:19:22,393 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:19:22,395 SequenceStep.py:93 DEBUG - Starting powerOffEpu prerequisite tests 2006-03-06 19:19:22,396 SequenceStep.py:95 DEBUG - Completed powerOffEpu prerequisite tests - result:True 2006-03-06 19:19:22,396 PowerOffEpu.py:52 INFO - Powering off EPU 0... 2006-03-06 19:19:23,374 LIM.py:226 DEBUG - LIM State: 1 8 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:23,382 LIM.py:226 DEBUG - LIM State: 1 5 0x210077f8:('PIG_INMUD', '"Happy as a pig in mud"') 2006-03-06 19:19:23,424 PowerOffEpu.py:61 INFO - Verified power off action. 2006-03-06 19:19:23,425 PowerOffEpu.py:65 INFO - Completed power off action for EPU 0, result:True 2006-03-06 19:19:23,426 PowerOffEpu.py:72 DEBUG - Starting powerOffEpu verification tests 2006-03-06 19:19:23,426 PowerSequenceStep.py:516 INFO - Checking if EPU 0 voltage is within range [0.0, 0.5]... 2006-03-06 19:19:25,380 SequenceStep.py:539 INFO - PDU 0 EPU 0 3.3V voltage measured as 0.22V and within the required range of [0.0, 0.5] 2006-03-06 19:19:25,380 PowerOffEpu.py:81 DEBUG - Completed powerOffEpu verification tests - result:True 2006-03-06 19:19:25,382 SequenceStep.py:416 DEBUG - Configuring LHK with the default configuration 2006-03-06 19:19:26,395 SequenceStep.py:421 INFO - Configured LHK with the default configuration 2006-03-06 19:19:26,396 SequenceStep.py:93 DEBUG - Starting powerOffGasuPdu prerequisite tests 2006-03-06 19:19:26,397 SequenceStep.py:95 DEBUG - Completed powerOffGasuPdu prerequisite tests - result:True 2006-03-06 19:19:26,397 PowerOffGasuPdu.py:52 INFO - Sending Load Shed to power off the GASU and the PDU 2006-03-06 19:19:27,370 LIM.py:226 DEBUG - LIM State: 1 16 0x598cf25c:('LIM_PKTSENT', '"Command or telemetry packet was sent to another task"') 2006-03-06 19:19:32,370 LIM.py:226 DEBUG - LIM State: 1 9 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:19:43,370 LIM.py:226 DEBUG - LIM State: 1 10 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:19:43,375 LIM.py:226 DEBUG - LIM State: 1 17 0x598333a8:('LIM_SUCCESS', '"Success"') 2006-03-06 19:19:46,398 PowerOffGasuPdu.py:60 INFO - Verified completion of power off due to a Load-Shed command. 2006-03-06 19:19:46,399 PowerOffGasuPdu.py:64 INFO - Completed Load-Shed action, result:True 2006-03-06 19:19:46,400 SequenceStep.py:104 DEBUG - Starting powerOffGasuPdu verification tests 2006-03-06 19:19:46,400 SequenceStep.py:106 DEBUG - Completed powerOffGasuPdu verification tests - result:True 2006-03-06 19:19:46,401 SequenceStep.py:93 DEBUG - Starting powerConsumption prerequisite tests 2006-03-06 19:19:46,402 SequenceStep.py:95 DEBUG - Completed powerConsumption prerequisite tests - result:True 2006-03-06 19:19:46,402 PowerConsumption.py:74 DEBUG - Starting powerConsumption verification tests 2006-03-06 19:19:46,968 SequenceStep.py:539 INFO - LAT input power measured as 21.98W and within the required range of [0, 750] 2006-03-06 19:19:46,968 PowerConsumption.py:62 INFO - Dwelling on the power rack for 10 seconds... 2006-03-06 19:19:56,969 SequenceStep.py:539 INFO - LAT average input power measured as 17.42W and within the required range of [0, 650] 2006-03-06 19:19:56,970 SequenceStep.py:539 INFO - LAT peak input power measured as 24.70W and within the required range of [0, 750] 2006-03-06 19:19:56,971 PowerConsumption.py:92 DEBUG - Completed powerConsumption verification tests - result:True 2006-03-06 19:19:56,972 seAppBase.py:418 DEBUG - seAppBase.seStopRun -- LatPowerOff 2006-03-06 19:19:57,032 seAppBase.py:932 DEBUG - Generating run report... 2006-03-06 19:19:57,035 rcReportGen.py:95 DEBUG - Database elogbook opened successfully 2006-03-06 19:19:57,277 seAppBase.py:1058 DEBUG - Run report generation complete. 2006-03-06 19:19:57,277 seAppBase.py:1179 INFO - seAppBase.seStopRun -- Test LatPowerOff finished, Run Id: 101000045, Status: PASSED, Completion Time: Mon Mar 6 19:19:57 2006