| Name | Value | Description |
| CALTransverseStayClear |
364 mm |
Transverse dimension of
CAL Stay Clear envelope from LAT-DS-00038-2 |
| CALVertStayClear |
224.3 mm |
Z-dimension of CAL
Stay Clear envelope from LAT-DS-00038-2 |
| diodeX |
0.3 mm |
Depletion depth of diode Si
|
| diodeLY |
14.5 mm |
Width of large diode Si
|
| diodeSY |
2.4 mm |
Width of small diode Si
|
| diodeZ |
10.5 mm |
Height of diode Si
|
| CsILength |
326 mm |
Length of a CsI crystal as of 30May02
|
| CsIWidth |
26.7 mm |
(Transverse) width of
a CsI crytal. Changed from 26.714mm on 18 June, 2003. |
| CsIHeight |
19.9 mm |
Height of a CsI crystal
|
| diodeZOffset |
0.55 mm |
Z offset of diodes relative to
crystal. Changed from .9 mm 18 June, 2003. |
| diodeLYOffset |
-2.6 mm |
Y (transverse) offset of
large diode relative to crystal. Changed from -2.55 mm on 18 June, 2003 |
| diodeSYOffset |
8.025 mm |
Y offset of small diode relative
to crystal. Changed from 8.6 mm on 18 June, 2003. |
| cellVertPitch |
21.35 mm |
Vertical pitch of CsI and
cells |
| cellHorPitch |
27.84 mm |
Horizontal pitch of CsI
and cells. Changed from 27.844 mm on 18 June, 2003. |
| CsIWrapThick |
0.0065 mm |
Thickness of crystal wrap
(reflector VM2000), as of 18 June, 2003. |
| cellVertWallThick |
0.45 mm |
Thickness of
composite cell vertical walls (C) [only. Before 18 June, 2003, also
includedreflector]
|
| cellHorWallThick |
0.85 mm |
Thickness of
composite cell horizontal walls (C) |
| cellSideWallThick |
1.685 mm |
Thickness of vertical cell
wall for outermost cells in each layer. New constant, first defined
18 June, 2003 |
| cellTopWallThick |
2.43 mm |
Thickness of horizontal cell wall
above top layer. New constant, first defined 18 June 2003. |
| cellBottomWallThick |
4.43 mm |
Thickness of horizontal cell
wall below bottom layer. New constant, first defined 18 June 2003. |
| CALSideWallThick |
12 mm |
Horizontal thickness
of side compartment with electronics. Changed from 11.6 mm as of
18 June, 2003. |
| CALGridFrameGap |
1.5 mm |
Minimum gap between
top of CAL (frame) and bottom of grid flange. 3 Sept. 2003 |
| CALSideWallInnerThick |
1 mm |
Horizontal thickness
of inner wall within (largely hollow) side wall |
| CALSideWallOuterThick |
0.8 mm |
Horizontal thickness
of outer wall within (largely hollow) side wall. Changed from 1.0 mm as
of 18 june, 2003. |
| CALSideWallPCBThick |
1.6 mm |
Horizontal thickness
of PCB within (largely hollow) side wall |
| CALInnerWallPCBGap |
3.7 mm |
Gap between CAL closeout and PCB
layer of side wall |
| CALModuleWidth |
363 mm |
Horizontal, face-to-face
dimension of CAL module (presumably both X and Y) |
| CALModuleHeight |
222 mm |
Vertical, top-to-bottom
dimension of CAL module. Changed from 223.8 mm as of 18 June, 2003. |
| CALCylSupportDiameter |
10 mm |
Diameter of
cylindrical supports (Al) |
| CALCylSupportCellDelta |
4 |
Number of
cells between adjacent (in the same layer) cylindrical supports |
| CALFrameSideThick |
8 mm |
Thickness of CAL frame sides
|
| CALTopFrameZ |
16 mm |
Thickness of top of
CAL frame (Al) |
| CALBottomFrameZ |
14 mm |
Thickness of bottom of
CAL frame (Al) Changed 4 Sept. 2003 from 16.0 (ref: Sasha) |
| CALTopFrameWidth |
16.7 mm |
Width of top picture
frame. Changed from 22 to 16.7 19 June 2003.(Al) |
| CALBottomFrameWidth |
35 mm |
Width of bottom picture
frame (Al) |
| CALTopPlateZ |
2.43 mm |
Vertical thickness of CAL
top plate composite. Changed from 2.0 mm as of 18 June, 2003. |
| CALBottomPlateZ |
4.43 mm |
Vertical thickness of CAL
bottom plate composite. Changed from 4.0 mm as of 18 June, 2003. |
| CALBottomRibPitch |
73 mm |
Pitch of bottom plate
ribs (Al) |
| CALBottomRibWidth |
10 mm |
Width of bottom plate
ribs (Al) |
| CALBottomRibThick |
12 mm |
Thickness of bottom plate
ribs (Al) |
| CALMountTabThick |
15 mm |
Thickness of CAL mounting
tabs, CAL to grid (Al) |
| CALMountTabWidth |
12 mm |
Width of CAL mounting
tabs |
| CALCloseoutLen |
338 mm |
Transverse length of innermost
components of CAL side wall, equal to gap between opposing closeout
walls. Added as primary 24 June 2003 |
| CALTopFrameUpperWidth |
13.2 mm |
Frame width for upper
of two top frame pieces. 19 June 2003 |
| CALTopFrameLowerWidth |
7.5 mm |
Frame width for lower
of two top frame pieces. 19 June 2003 |
| CALTopFrameLowerZ |
10 mm |
Frame height for lower
of two top frame pieces. 19 June 2003 |
| Name | Value | Description |
| TKRTransverseStayClear |
372 mm |
Tranverse dimension of
TKR Stay Clear envelope from LAT-DS-00038-2 |
| TKRVertStayClear |
640 mm |
Z dimension of
TKR Stay Clear envelope from LAT-DS-00038-2 |
| SiThick |
0.4 mm |
Si thickness |
| coreThick |
27.92 mm |
Thickness of core material
in all trays except the bottom and top |
| coreThickBot |
36.535 mm |
Core thickness for
top tray (20Jun03) |
| coreThickTop |
33.995 mm |
Core thickness for
top tray (20Jun03) |
| TKRCloseoutWidth |
5 mm |
Width of closeout
walls. Last modified 2aug02 |
| glueSiThick |
0.15 mm |
Thickness of glue
between Si and bias plane |
| glueCoreThick |
0.075 mm |
Thickness of glue between
core (or closeout) and something else (15oct01) |
| glueDefThick |
0.1 mm |
Default glue thickness,
when neither Si nor core is involved (15oct01) |
| convThickReg |
0.105 mm |
Thickness of conversion
material in "regular" layers in mm |
| convThickSup |
0.723 mm |
Thickness of conversion
material in super-GLAST trays in mm (as of 15 oct 2001) |
| faceThick |
0.2 mm |
Face sheet thickness
for all but super-glast tray and bottom tray (as of 15oct01) |
| faceSupThick |
0.29 mm |
Face sheet thickness
for super-glast trays and bottom tray (15oct01) |
| biasPlaneThick |
0.1 mm |
Thickness of bias
plane (15oct01) |
| tray0Gap |
2.05 mm |
Gap above bottom tray
modified 21jun03 |
| trayNoCnvGap |
2.13 mm |
Gap above non-bottom
no-converter trays |
| traySuperGap |
2.127 mm |
Gap above super-glast
trays |
| trayRegGap |
2.125 mm |
Gap above regular trays. Last
modified 2aug02 |
| TKRTraysTotalZ |
627.465 mm |
Height of a tracker tower.
(From spreadsheet, 21jun03 |
| TKRFootZ |
4.5 mm |
Height of foot between bottom of bottom tray
and grid |
| ssdGap |
0.025 mm |
gap between Si dies within a ladder
(15oct01) |
| SiWaferSide |
89.5 mm |
Length and width of Si wafer |
| SiWaferActiveSide |
87.552 mm |
Length and width of active
area on a wafer |
| faceWidth |
360.6 mm |
X and y width of face sheet
(15oct01) |
| TKRElectGap |
4.2 mm |
Distance between wall
and panel edge (each edge) |
| ladderGap |
0.2 mm |
gap between ladders |
| MCMHeight |
23 mm |
Height of tracker MCM boards |
| MCMThick |
1.1 mm |
Thickness of tracker MCM
boards |
| MCMGap |
0.1 mm |
Gap between MCM board and closeout
|
| TKRWallThick |
1.5 mm |
Thickness of tracker
walls |
| TKRWallLength |
371.45 mm |
Outer dimension of square
formed by tracker walls (Z cross-section)
Last modified 2aug02 |
| Name | Value | Description |
| ACDTransOuterSC |
1796 mm |
Maximum transverse outer extent
of ACD (from LAT-DS-00038) |
| ACDTransInnerSC |
1515.5 mm |
Minimum transverse inner
envelope for ACD sides (from LAT-DS-00038) |
| ACDTransInnerSCflange |
1574 mm |
Minimum transverse inner
envelope for lower part of ACD sides (from LAT-DS-00038) |
| ACDVertSC |
1015 mm |
Max. delta Z from top to bottom of
ACD (from LAT-DS-00038) |
| topTileXEdge_l |
329.667 mm |
X dimension of outermost (in X)
top tiles, i.e., columns 0 and 4. Modified November 05 from new (2005)
3-d model |
| topTileXMid_l |
332 mm |
X dimension of tiles in columns
1 and 3. Modified Nov '05 from 3-d model of 2005. |
| topTileXCentral_l |
332 mm |
X dimension of central top tiles
(column 2) Modified Nov '05 from 3-d model of 2005. |
| topTileYEdge_l |
355 mm |
Y dimension of outermost (in y)
top tiles, i.e., rows 0 and 4.
Modified Nov '05 from 3-d model of 2005. |
| topTileYMid_l |
344 mm |
Y dimension of tiles in rows
1 and 3. Modified Nov '05 from 3-d model of 2005. |
| topTileYCentral_l |
344 mm |
Y dimension of central top tiles
(row 2) Modified Nov '05 from 3-d model of 2005. |
| tileThickness |
10 mm |
Thickness of ACD tiles
*except* for top center tiles |
| tileCenterThickness |
12 mm |
Thickness of ACD tiles,
middle column of top only |
| topTileGap |
2 mm |
Worst-case (most thermal expansion)
transverse gap between tiles on the top. Revised Oct. 2002 to 3.5.
Revised again July '03. Nov. 2005: gap occurs in X (so between adjacent
columns)
use number from 3-d model of 2005. |
| topOverlap |
20 mm |
Width of overlap
of overlapped top tiles (changed from 10.0, as of Oct. 2002;
changed from 15 in July '03. Get 20 from 3-d model (6-23-03))
Still correct as of Nov. 05 |
| topTileOuterZGap |
2.6 mm |
Gap in Z between top tile
in row. 0 (resp. 4) and its neighbor in row. 1 (resp. 3).
Last revised Nov. 2005 (swap col for row; value now 2.6) |
| topTileInnerZGap |
2.6 mm |
Gap in Z between top tile
in row. 3 and its neighbor in rows. 2 and 4.
Last revised Nov. 2005 (swap col for row; value now 2.6) |
| sideTileR0_dt |
839.97 mm |
Transverse displacement
of top row of side tiles, last revised Nov 2005 from new 3-d model |
| topTileBentZ |
50 mm |
Z dimension for extra box stuck onto
the bottom of top tiles in rows 0 and 4 to simulate a bent tile. |
| sideTileHeight0 |
366 mm |
Height of top row
of side tiles. From 3-d model (6-23-03) |
| sideTileHeight1 |
199.46 mm |
Height of 2nd row
of side tiles as simulated (no slant; no gaps or overlaps between
rows). |
| sideTileHeight2 |
150 mm |
Height of 3rd row
of side tiles as simulated (no slant; no gaps or overlaps between rows. |
| sideTileHeight3 |
135.35 mm |
Height of 4th row
of side tiles as simulated (no overlaps or gaps). True height from
3-d model 6-23-03 would be 155 |
| sideOverlap |
30 mm |
Distance side tiles
extend above topACD tile surface --- used for positioning.
(7/28/03) 3-d model 6-23-03 essentially agrees with this.
(11/2205) So does latest 3-d model |
| sideVerticalGap |
0 mm |
Vertical gap
between (rows of?) side tiles |
| sideHorizontalGap |
2 mm |
Horizontal
gap at the corners between adjacent columns of side tiles (July 03; revised
according to 3-d model 6-23-03, from old value of 3.0)
(11/22/05) 2.0 still correct. |
| ACDTileScale |
0.9968 |
Scale factor
used to transform tile dimensions to operating temperature:
5*10**(-5) by 40 degrees, from Alex. Added July 2005 |
| ACDHoleRad |
1.59 mm |
Radius of hole in tile.
Added July 2005 |
| ACDScrewRad |
1.4 mm |
Radius of screw in tile.
Added July 2005 |
| ACDScrewLen |
25.4 mm |
Length of screw in tile.
Added July 2005 |
| ACDScrewFromEdge |
50 mm |
Distance of (most) screws from edge of tile
|
| ACDScrewCenterDiff |
50 mm |
Distance between centers of screws in a screw square (in bottom side
tiles)
|
| ACDSideCoreThickness |
25.4254 mm |
Thickness (short
transverse dimension) of side support
structure for ACD, not including face sheets. As of Nov. 05 |
| ACDTopCoreThickness |
50.8254 mm |
Thickness of top support
structure for ACD, not including face sheets. As of Nov., 2005 |
| ACDTopCoreTrans |
1532.72 mm |
X and Y dimensions.
From 3-d model, Nov. 05
|
| ACDSideCoreZ |
674.11 mm |
Height of ACD side core from
3-d model, Nov. 05 |
| ACDSideCoreTrans |
1558.78 mm |
Long transverse dimension
(x or y) of ACD side core. From 3-d model, Nov. 05 |
| ACDFaceThickness |
0.508 mm |
Thickness of face sheets used
in ACD support structure, both top and sides. As of Nov. 05 |
| ACDTopSupport_dz |
683 mm |
Displacement of top support
w.r.t. Ritz origin. From 3-d model (Nov 05) |
| ACDSideSupport_dt |
779.9 mm |
Transverse displacement of
side support, from 3-d model 6-23-03, confirmed for Nov 05 |
| ACDSideSupport_dz |
371.16 mm |
Z-displacement of
side support, from 3-d model Nov 05 |
| ACDSideSupport_dDovetail |
13.03 mm |
Small offset needed
for sides to dovetail around top support, from 3-d model (Nov 05 |
| PMTFiberGap |
41.6 mm |
Minimum distance between
outer edge of side support structure and inner edge of innermost
side tile. Side ribbons (as well as PMT fibers) may go in this gap |
| topTileSupportStandoff |
25.4 mm |
Minimum distance
between lowest top tiles and top of ACD support. Ribbons are placed
within this gap. Not actually used. |
| dovetailGap |
3.3 mm |
Distance between adjacent ACD sides
of tiles (11/22/05) Still 3.3 |
| ACDSideTopTileGap |
3.3 mm |
Transverse distance between
top edge tile and nearest side tile. From 3-d model 6-23-03.
(11/22/05) Still 3.3 |
| ACDTileMaxZ |
775 mm |
Very top of top tiles in
columns 0 and 4, from 3-d model Nov. 05 |
| ACDTopSupportMaxZ |
708.918 mm |
Very top of top of ACD
support structure (including face sheet) under top tiles,
from 3-d model Nov. 05 |
| ribbonWidth |
14 mm |
Width of scintillating ribbon
(from 3-d model 6-23-03, still ok Nov. 05) |
| ribbonThickness |
5 mm |
Thickness of scintillating ribbon, confirmed 30 July 2003, Nov. 05 |
| ribbonGap |
1.5 mm |
Distance between ribbon and the adjacent
top tile, as of Oct. 2002.
As of new 3-d model 6-23-03 old value of 2.5 caused overlap. With
no official blessing, try something smaller. According to (old) model there
is no gap between ribbon and topmost tiles. As of Nov. 05, gap
appears to be about 1.5 or 2 mm |
| ribbonOverlap |
15 mm |
Amount X ribbon segment overshoots
tile edge of tile it's under. (This is a figment of the simulated
model. Real ribbons don't come in disconnected segments.) |
| xRibbonOuter_dx |
501.8 mm |
X displacement of outer
X-ribbon (contained in YZ plane): ribbon #3 (Nov 05) |
| xRibbonInner_dx |
166 mm |
X displacement for X-ribbon
#2 (Nov 05) |
| yRibbonOuter_dy |
502 mm |
Y displacement of outer
Y-ribbon (contained in XZ plane): ribbon #3 (Nov 05) |
| yRibbonInner_dy |
168.4 mm |
Y displacement for Y-ribbon
#2 (Nov 05) |
| yRibbonTopAbs_dz |
724 mm |
Z displacement (w.r.t. origin)
of top segment of Y ribbons (the flat ones) as of Nov. 05 |
| Name | Value | Description |
| NADGridWebInner |
8 mm |
Full thickness of grid between
towers (not half-width) Verified against LAT-DS-01579 on 5 May 2004.
|
| NADGridWebOuter |
13 mm |
Thickness of grid on outside
towers.
Verified against LAT-DS-01579 on 5 May 2004. Correct for bulk of web;
lower bound for bottom.
Bottom of grid has variable thickness of up to 42.24 mm.
|
| NADGridWebZ |
210.8 mm |
Height of grid web.
Verified against LAT-DS-01579 on 5 May 2004. |
| NADGridWebCutout |
366.5 mm |
Cut-outs for calorimeters.
Verified against LAT-DS-01579 on 5 May 2004. |
| NADGridFlangeZ |
25.4 mm |
Height of grid flange.
Verified against LAT-DS-01579 on 5 May 2004. |
| NADGridFlangeCutout |
346.6 mm |
Cutouts in the flange.
Verified against LAT-DS-01579 on 5 May 2004.
|
| NADGridFlangeInner |
27.9 mm |
Thickness of inner parts of
grid flange. Verified against LAT-DS-01579 on 5 May 2004. |
| NADGridFlangeOverhang |
25 mm |
Flange overhangs web.
Verified against LAT-DS-01579 on 5 May 2004. |
| NADBlanketTopThick |
30.22 mm |
Blanket thickness as of
May, 2006. See
https://confluence.slac.stanford.edu/display/ACD/Thermal+Blanket |
| NADBlanketSideThick |
30.8 mm |
Blanket thickness as
of May, 2006. See
https://confluence.slac.stanford.edu/display/ACD/Thermal+Blanket |
| NADCrownToTile |
2.26 mm |
Distance from top of side tile
to bottom of crown of blanket (room temperature). May, 2006. |
| NADBlanketToTopTile |
6.89 mm |
Distance from top tile
to bottom of blanket. May, 2006 |
| NADCrownWidth |
101.6 mm |
Transverse distance across
crown. May, 2006 |
| NADCrownDepth |
31.75 mm |
Z-distance from top of crown
to top of lower, central part of blanket. May, 2006 |
| NADBlanketTopTrans |
1790.7 mm |
Max transverse distance
across top blanket, from outside of crown. From as-build document
ACD-RPT-000394 RevA |
| NADBlanketSideZ |
918 mm |
Z-dimension of blanket
sides, from
https://confluence.slac.stanford.edu/display/ACD/Thermal+Blanket,
May, 2006 |
| NADSpacecraftZ |
1400 mm |
Height of spacecraft |
| NADSpacecraftR |
817.775 mm |
Radius of spacecraft
(800.0 * sqrt(1/(0.957)) to make mass equal to about 1000 kg |
| NADSpacecraftGap |
0 mm |
Gap between LAT and spacecraft |
| NADSolarRodLength |
1000 mm |
Length of connecting
rods for solar panels |
| NADSolarRodR |
50 mm |
Radius of connecting
rods for solar panels |
| NADSolarPLength |
5000 mm |
Solar panel length (extending
out from spacecraft) |
| NADSolarPWidth |
1500 mm |
Solar panel width |
| NADSolarSiThick |
4 mm |
Solar panel thickness |
| NADSolarCoreThick |
2 mm |
Solar panel thickness |
| Name | Value | Description |
| CsISegLength |
27.1667 mm |
length along measurement dimension of a CsI segment |
| nCsISegM1 |
11 |
upper limit for id field keeping track of segment number
|
| CALMaxLayer |
7 |
upper limit on Cal layer idfield value |
| diodePosXOffset |
163.15 mm |
X-offset of a diode relative to the center of the
CsI crystal |
| diodeNegXOffset |
-163.15 mm |
X-offset of diode on negative end of a crystal |
| cellVertWallHalfThick |
0.225 mm |
convenience |
| cellHorWallHalfThick |
0.425 mm |
convenience |
| CsIEnvX |
326.6 mm |
Long dimension of envelope containing a CsI crystal
and its diodes |
| CsIEnvY |
27.84 mm |
Transverse dimension of envelope containing a CsI
crystal and its diodes |
| CsIEnvZ |
21.35 mm |
Height of the envelope containing a CsI crystal and
its diodes |
| cellIntWallZ |
20.5 mm |
Height of vertical wall, up to but not including
horizontal walls |
| CsIWrapTranvLen |
26.713 mm |
Extent (in Y or X, perp. to main axis of crystal)
of crystal wrap |
| cellHorWall_dz |
10.4625 mm |
Z position rel. to cell of upper horiz. wall |
| cellHorWall_dzn |
-10.4625 mm |
Z position rel. to cell of lower horiz. wall |
| cellVertWall_dy |
13.8075 mm |
Y displacement rel. to cell of vertical cell wall
(here Y means perp. to height and length directions) |
| cellVertWall_dyn |
-13.8075 mm |
Neg. of Y displacement rel. to cell of vertical cell wall
(here Y means perp. to height and length directions) |
| wrapHorWall_dz |
9.95325 mm |
Z positionrel. to cell of upper crystal wrap box |
| wrapHorWall_dzn |
-9.95325 mm |
Z position rel. to cell of lower crystal wrap box |
| wrapVertWall_dy |
13.3532 mm |
Z position rel. to cell of +y side crystal wrap box |
| wrapVertWall_dyn |
-13.3532 mm |
Z position rel. to cell of -y side crystal wrap box |
| cellTopExtraThick |
2.005 mm |
Extra thickness of cell material on top layer, beyond
what the standard layer has |
| cellBottomExtraThick |
4.005 mm |
Extra thickness of cell material on bottom layer, beyond
what the standard layer has |
| cellSideExtraThick |
1.46 mm |
Extra thickness of cell material on side of
outermost crystal, beyond interior crystals have. |
| CALLayerNonmeasWidth |
337 mm |
Width of a layer in non-meas direction. Logs
plus two bits of extra carbon cell material
on the sides |
| CALLayerTrans |
337 mm |
Transverse dimension of a CAL layer:
max(CsiEnvX, nEltPerlayer*cellHorPitch) |
| CALLayersTotalZ |
176.81 mm |
Includes cal layers and inter-layer walls but not frame,
grid, etc. (may be superseded by info from Eric) |
| CALTopFrameLowerLen |
338 mm |
Outer dimension of lower of two top frame pieces |
| CALTopFrameUpperZ |
6 mm |
Height of top frame is derived from total frame Z and
lower height, which are primary |
| CALTopFrameUpperLen |
350.6 mm |
Outer dimension of upper of two top frame pieces |
| CALTopFrameLowerCutoutLen |
323 mm |
Length of the side of the square vacuum cutout for
lower of two top frame pieces. |
| CALTopFrameUpperCutoutLen |
324.2 mm |
Length of the side of the square vacuum cutout for
upper of two top frame pieces. |
| CALFrameWidth |
353 mm |
transverse dimension for cal frame (one tower) |
| CALBottomFrameShort |
293 mm |
Length of shorter pieces in CAL bottom frame |
| CALBottomFrame_dt |
164 mm |
Transverse displacement of bottom frame pieces |
| CALBottomFrame_dtn |
-164 mm |
Negative transverse displacement of bottom
frame pieces |
| CALFramedLayersZ |
206.81 mm |
Z dimension of CsI layers plus frame. Note
This constant may need updating if description of
CAL changes! Constant instituted 30 April 2003 |
| CALBottomFrame_dz |
-90.15 mm |
Offset of bottom frame relative to stay-clear box.
Later will probably have to locate different frame
pieces separately. |
| CALLayers_dz |
5.255 mm |
Offset of vol. containing layers relative to
stay-clear box. Upper frame is at top of box,
followed by CALLayers.
Constant instituted 30 April 2003.
Modified 20 June when CALLayers was redefined to
exclude frame. Modified 3 Sept 2003 to align
CAL bottom frame with bottom of grid web |
| CALTopFrameLower_dz |
98.66 mm |
Displacement for lower of 2 top frame pieces
within stay-clear |
| CALTopFrameUpper_dz |
106.66 mm |
Displacement for upper of 2 top frame pieces
within stay-clear |
| CALOuterWallPCBGap |
4.9 mm |
Gap between CAL outer side wall Al component and PCB
layer. Comparable gap on other side is primary constant. |
| CALCloseoutGap |
0.5 mm |
Distance from closeout (inner
part of CAL side wall) and carbon fiber cell about crystals.
As of 24 June 2003, derived |
| CALSidePCBLen |
347.4 mm |
Transverse length of PCB component of CAL side wall |
| CALSideOuterLen |
360.4 mm |
Transverse length of outer Al component of CAL
side wall |
| CALCloseoutZ |
186.81 mm |
Height of CAL closeout (and, with current model, also
PCB. **To be revised.
For now (20 June 2003) have shortened closeout
pieces to only run down to top of bottom frame.**
|
| CALSidePCBZ |
186.81 mm |
Height of CAL side wall PCB. **To be revised.
For now (20 June 2003) have shortened side PCB
pieces to only run down to top of bottom frame.**
|
| CALSideOuterZ |
192.81 mm |
Height of outermost component of CAL side wall
**To be revised.
For now (20 June 2003) have shortened side
pieces to only run down to top of bottom frame.**
|
| CALCloseout_dt |
169.5 mm |
Transverse offset of CAL closeout walls |
| CALCloseout_dtn |
-169.5 mm |
Transverse offset of negative CAL closeout walls |
| CALCloseout_dz |
10.255 mm |
Vertical offset of CAL side closeouts |
| CALSidePCB_dt |
174.5 mm |
Transverse offset of CAL side PCB walls |
| CALSidePCB_dtn |
-174.5 mm |
Transverse offset for negative CAL side PCB walls |
| CALSidePCB_dz |
10.255 mm |
Vertical offset of CAL side PCB |
| CALSideOuter_dt |
180.6 mm |
Transverse offset of outer Al component of
CAL side walls |
| CALSideOuter_dtn |
-180.6 mm |
Transverse offset of negative outer Al component of
CAL side walls |
| CALSideOuter_dz |
13.255 mm |
Vertical offset of outer Al component of CAL side
walls. Assume top of it lines up with top of frame. |
| eBottomFrame |
18 |
For use in identifiers |
| eTopFrame |
19 |
For use in identifiers |
| eBottomPlate |
20 |
For use in identifiers |
| eTopPlate |
21 |
For use in identifiers |
| Name | Value | Description |
| TKRCloseoutTrans |
360.6 mm |
Transverse dimension of the business part of the
tray, large enough to include all silicon, closeout,
etc. but no larger (Revised 3May02) |
| TKRTotalZ |
631.965 mm |
total space occupied by tracker, including foot |
| TKRTrayWidth |
363 mm |
Large enough to include 2 MCM boards (and 2 gaps) as
well as closeout. |
| waferPitch |
89.525 mm |
Distance between centers of adjacent wafers in
a ladder |
| ladderPitch |
89.7 mm |
Distance between centers of adjacent wafers in
adjacent ladders |
| TKRGuardRing |
0.974 mm |
Width of dead region around outside of Si wafer |
| TKRBiasWidth |
360.6 mm |
Transverse dimension of bias board (for now assuming
it's a square |
| TKRCloseoutThick |
27.92 mm |
Z dimension of closeout for trays other than top
and bottom |
| TKRCloseoutThickBot |
36.535 mm |
Z dimension of closeout for bottom tray |
| TKRCloseoutThickTop |
33.995 mm |
Z dimension of closeout for top tray |
| TKRCloseoutLen |
360.6 mm |
Transverse length of longer of (imaginary) closeout
pieces, just the same as the face sheet |
| TKRCloseoutLenShort |
350.6 mm |
Transverse length of shorter of (imaginary) closeout
pieces |
| TKRCoreWidth |
350.6 mm |
Length of sides for core |
| TKRCloseout_dt |
177.8 mm |
Transverse (x or y) offset of closeout pieces
w.r.t. tray |
| MCMLength |
360.6 mm |
Long transverse dimension of MCM board |
| TKRWallLengthShort |
368.45 mm |
For the XML description, tracker wall is broken up
into 4 pieces: 2 long ones extending in X and two slightly
shorter ones extending in Y. This is the length of the
shorter ones. |
| TKRWall_dt |
184.975 mm |
Positive transverse offset of TKR wall, relative to
center of a tower |
| TKRWall_dtn |
-184.975 mm |
Negative transverse offset of TKR wall, relative to
center of a tower |
| TKRCloseout_dtn |
-177.8 mm |
Negative transverse offset of closeout pieces |
| TKRMCMint_dz |
2.46 mm |
Offset of MCM board on + side w.r.t. enclosing envelope
for interior (not top or bottom) boards
|
| TKRMCMint_dzn |
-2.46 mm |
Offset of MCM board on - side w.r.t. enclosing envelope
for interior (not top or bottom) boards
|
| TKRMCMextTop_dz |
5.4975 mm |
Offset of MCM board on + side w.r.t. enclosing envelope
for top board
|
| TKRMCMextTop_dzn |
-5.4975 mm |
Offset of MCM board on - side w.r.t. enclosing envelope
for top board
|
| TKRMCMextBot_dz |
6.7675 mm |
Offset of MCM board on + side w.r.t. enclosing envelope
for top board
|
| TKRMCMextBot_dzn |
-6.7675 mm |
Offset of MCM board on - side w.r.t. enclosing envelope
for top board
|
| TKRMCM_dt |
180.95 mm |
Transverse (x or y) offset of MCM board |
| TKRMCM_dtn |
-180.95 mm |
Negative transverse (x or y) offset of MCM board |
| biasGlueThick |
0.35 mm |
Thickness of upper bias board and glue above it |
| TKRTopFaceRegZ |
0.625 mm |
Thickness of combined glue+ face-sheet + glue +
bias-board + glue for non-superGLAST trays |
| TKRTopFaceSupZ |
0.715 mm |
Thickness of combined glue+ face-sheet + glue +
bias-board + glue for superGLAST trays |
| TKRBotFaceRegZ |
0.375 mm |
Thickness of bottom face sheet and surrounding glue
for non-superGLAST trays |
| TKRBotFaceSupZ |
0.465 mm |
Thickness of bottom face sheet and surrounding glue
for superGLAST trays |
| TKRFaceMinZ |
0.275 mm |
Thickness of regular face sheet and glue attaching
it to core/closeout |
| TKRFaceMinBotZ |
0.365 mm |
Thickness of regular face sheet and glue attaching
it to core/closeout |
| TKRMaxNoCnv |
2 |
Tray number of most forward no-converter tray |
| TKRMaxReg |
17 |
Tray number of most forward "regular" tray. Top
tray doesn't qualify since it has no top Si. |
| nWaferAcrossM1 |
3 |
Used as bound for possible idField values |
| nLadderM1 |
3 |
Upper limit on ladder idField values |
| maxTray |
18 |
Upper limit on tray idField values |
| maxTrayM1 |
17 |
max tray number of tray with bottom Si wafers |
| maxWaferStripNum |
383 |
Upper limit on strip number within a wafer |
| Name | Value | Description |
| sideTileTransLesser |
329.667 mm |
Transverse dimension of one edge side tile tile per side:
column 4 for -X and +Y side (faces 1 and 4); column 0 for +X
side and -Y side (faces 2 and 3).
|
| sideTileTransGreater |
342.967 mm |
Transverse dimension of one edge side tile tile per side:
column 0 for -X and +Y side (faces 1 and 4); column 4 for
+X side and -Y side (faces 2 and 3).
|
| sideTileTransMid |
332 mm |
Transverse dimension of side tiles in columns 1,2 and 3. |
| ACDSideSupportThick |
26.4414 mm |
Thickness of core + face sheets for side support |
| ACDTopSupportThick |
51.8414 mm |
Thickness of core + face sheets for top support |
| ACDTop_z |
66.082 mm |
Z dimension of envelope which will contain
ACD top tiles and ribbons (1 nov 2002)
As of July, '03, simply use information from 3-d model
about location of top of topmost tiles and top of
support structure to compute this. |
| ACDTopZHalf |
33.041 mm |
for convenience |
| ACDTop_d |
741.959 mm |
Z displacement of top ACD relative to Ritz origin.
As of July, 2003, get frontmost tile position from
3-d model version 6-23-03; compute from there. |
| ACDSideThickness |
10 mm |
This isn't really correct. If overlapping and
slant are taken into account, ACDSideThickness is
over twice this value. (1 nov 2002) |
| ACDTotalTransSide |
1676.63 mm |
transverse length of collection of ACD side tiles,
e.g those alone -X side of instrument. Could be
used for envelope volume. Is also equal to transverse
dimension of the single tile in the bottom row.
(1 nov 2002). July '03. Now compute as sum of tranverse
dimensions of tiles in R0, columns 0-5, plus gaps |
| ACDTotalTransSideOp |
1671.26 mm |
Scaled for operating temperature
|
| tileThicknessOp |
9.968 mm |
Scaled tile thickness (all but top center tiles) |
| tileCenterThicknessOp |
11.9616 mm |
Scaled tile thickness for top center tiles) |
| ACDSidesGap |
1669.94 mm |
Min. distance between tiles of the two sides || to x-axis
or equivalently of the two sides || to y-axis.
Use displacement info for top row of tiles from from 3-d model
|
| ACDTopTransverse |
1663.34 mm |
Transverse dimension of envelope which will contain
ACD top tiles and ribbons. As of July 2003, just set to
value large enough to include all top tiles as positioned
from 3-d model. From this model there is an approx. 3 mm
(actually 3.3) gap between side tiles (top row) and top tiles
|
| ACDTotalX |
1690.94 mm |
Total extent in X of entire collection of ACD pieces,
plus a millimeter for good luck (4 nov 2002) |
| ACDTotalY |
1690.94 mm |
Total extent in Y of entire collection of ACD pieces |
| topTileXEdge_lOp |
328.612 mm |
Scaled version of topTileXEdge_l
|
| topTileXMid_lOp |
330.938 mm |
Scaled for operating temperature
|
| topTileXCentral_lOp |
330.938 mm |
Scaled for operating temperature
|
| topTileYEdge_lOp |
353.864 mm |
Scaled for operating temperature
|
| topTileYMid_lOp |
342.899 mm |
Scaled for operating temperature
|
| topTileYCentral_lOp |
342.899 mm |
Scaled for operating temperature
|
| topTileBentZOp |
49.84 mm |
Scaled for operating temperature |
| sideTileHeight0Op |
364.829 mm |
Scaled for operating temperature
|
| sideTileHeight1Op |
198.822 mm |
Scaled for operating temperature
|
| sideTileHeight2Op |
149.52 mm |
Scaled for operating temperature
|
| sideTileHeight3Op |
134.917 mm |
Scaled for operating temperature
|
| sideTileTransLesserOp |
328.612 mm |
Scaled for operating temperature
|
| sideTileTransGreaterOp |
341.87 mm |
Scaled for operating temperature
|
| sideTileTransMidOp |
330.938 mm |
Scaled for operating temperature
|
| screwExtLen |
15.4 mm |
Length of screw part sticking out of normal-thickness tile
|
| screwExtThickLen |
13.4 mm |
Length of screw part sticking out of thick (top central) tile
|
| topScrewXEdge_dx |
139.833 mm |
x-displacement for screws on +x side of X-edge tiles
|
| topScrewXEdge_dxn |
-139.833 mm |
x-displacement for screws on -x side of X-edge tiles
|
| topScrewXMid_dx |
141 mm |
x-displacement for screws on +x side of X-mid tiles
|
| topScrewXMid_dxn |
-141 mm |
x-displacement for screws on -x side of X-mid tiles
|
| topScrewXCentral_dx |
141 mm |
x-displacement for screws on +x side of X-central tiles
|
| topScrewXCentral_dxn |
-141 mm |
x-displacement for screws on -x side of X-edge tiles
|
| topScrewYEdge_dy |
152.5 mm |
y-displacement for screws on +y side of Y-edge tiles
|
| topScrewYEdge_dyn |
-152.5 mm |
y-displacement for screws on -y side of Y-edge tiles
|
| topScrewYMid_dy |
147 mm |
y-displacement for screws on +y side of Y-mid tiles
|
| topScrewYMid_dyn |
-147 mm |
y-displacement for screws on -y side of Y-mid tiles
|
| topScrewYCentral_dy |
147 mm |
y-displacement for screws on +y side of Y-central tiles
|
| topScrewYCentral_dyn |
-147 mm |
y-displacement for screws on -y side of Y-edge tiles
|
| side0Screw_dz |
158 mm |
z-displacement for screws on +z side of top row (0) side tiles
|
| side0Screw_dzn |
-158 mm |
z-displacement for screws on -z side of top row side tiles
|
| side1Screw_dz |
74.73 mm |
z-displacement for screws on +z side of row 1 side tiles
|
| side1Screw_dzn |
-74.73 mm |
z-displacement for screws on -z side of row 1 side tiles
|
| side2Screw_dz |
50 mm |
z-displacement for screws on +z side of row 2 side tiles
|
| side2Screw_dzn |
-50 mm |
z-displacement for screws on -z side of row 2 side tiles
|
| sideLesserScrew_dt |
139.833 mm |
Transverse (x or y) displacement for screws on some narrower
side tiles (col 0 for sides 2 or 3; col 4 for
sides 1 and 4) |
| sideLesserScrew_dtn |
-139.833 mm |
Transverse (x or y) displacement for screws on outer
side tiles (negative direction |
| sideGreaterScrew_dt |
146.483 mm |
Transverse (x or y) displacement for screws on wider outer
side tiles (col 4 for sides 2 or 3; col 0 for
sides 1 and 4) |
| sideGreaterScrew_dtn |
-146.483 mm |
Transverse (x or y) displacement for screws on wider
side tiles (negative direction |
| sideMidScrew_dt |
141 mm |
Transverse (x or y) displacement for screws on
side tiles in cols 1,2,3 |
| sideMidScrew_dtn |
-141 mm |
Transverse (x or y) displacement for screws in side
tiles, cols 1,2,3 (negative direction) |
| tileSide_dt |
839.97 mm |
Transverse (perpendicular to plane of face) displacement
of side face of ACD |
| tileSide_dtn |
-839.97 mm |
Transverse (perpendicular to plane of face) displacement
of side face of ACD for "negative" faces |
| ACDScrewSqSide |
53.18 mm |
Total length of side of a minimal square containing a group
of 4 screws |
| ACDScrewSqMin_d |
139.272 mm |
Half of distance between centers of adjacent screw squares,
equal to transverse displacement of most central squares |
| ACDScrewSqMin_dn |
-139.272 mm |
Smallest neg. displacement of a screw square |
| ACDScrewSqMin3_d |
417.816 mm |
Displacement for squares 2 and 5 |
| ACDScrewSqMin3_dn |
-417.816 mm |
Neg. displacement (square 2) |
| ACDScrewSqMin5_d |
696.36 mm |
Displacement for squares 1 and 6 |
| ACDScrewSqMin5_dn |
-696.36 mm |
Neg. displacement (square 1) |
| screwInSq_d |
25 mm |
Displacement of a screw from center of screw square |
| screwInSq_dn |
-25 mm |
Negative displacement of a screw from center of
screw square |
| ACDSide_z |
850.81 mm |
Total height of an ACD side of tiles
(tiles plus gaps) |
| tileHalfThickness |
5 mm |
for convenience |
| sideTileRow0_d |
242.405 mm |
Z-Displacement for top row (row 0) of side tiles (X and Y),
relative to the center of a box containing the side |
| sideTileRow1_d |
-40.325 mm |
Displacement for row 1 side tiles (X and Y) |
| sideTileRow2_d |
-215.055 mm |
Displacement for row 2 side tiles (X and Y) |
| sideTileRow3_d |
-357.73 mm |
Displacement for row 3 side tiles (X and Y) |
| ACDSideDovetail_d |
6.65 mm |
Side tiles on sides parallel to X-axis (sides 2 and 4)
have a displacement in X of this amount, positive
for side 2 and negative for side 4. Similarly side 3
is displaced positively in Y by this amount, side 1
negatively.
|
| ACDSideDovetail_dn |
-6.65 mm |
Dovetail displacement for "negative" ACD sides |
| topTileEdge_dz |
770 mm |
Displacement w.r.t. LAT origin of
highest tiles, those in row [was col before Nov 05] 0 and 4 |
| topTileMid_dz |
757.4 mm |
Displacement w.r.t. LAT origin for
tiles in rows [was cols before Nov 05] 1 and 3 |
| topTileCent_dz |
743.8 mm |
Displacement w.r.t. LAT origin for
tiles in row [was col before Nov 05] 2 |
| topTileMid_dy |
324 mm |
Y displacement of top tiles in row 3 |
| topTileMid_dyn |
-324 mm |
Y displacement of top tiles in row 1 |
| topTileEdge_dy |
653.5 mm |
Y displacement of top tiles in row 4 |
| topTileEdge_dyn |
-653.5 mm |
Y displacement of top tiles in row 0 |
| topTileMid_dx |
334 mm |
X displacement of tiles in col 3 |
| topTileMid_dxn |
-334 mm |
X displacement of tiles in col 1 |
| topTileEdge_dx |
666.833 mm |
X displacement of tiles in col 4 |
| topTileEdge_dxn |
-666.833 mm |
X displacement of tiles in col 0 |
| topTileBent_dz |
740.096 mm |
Z displacement w.r.t origin of extra pieces needed to make
bent tiles |
| topTileBentR0_dy |
-825.448 mm |
Y displacement w.r.t origin of extra pieces needed to make
bent tiles in row 0 |
| topTileBentR4_dy |
825.448 mm |
Y displacement w.r.t origin of extra pieces needed to make
bent tiles in row 0 |
| topYRibbon_dz |
724 mm |
Z displacement rel. to containing envelope
for long ribbon segments running || to
X-axis along top. |
| ribbonHalfThickness |
2.5 mm |
for convenience |
| yRibbonTop_l |
1663.34 mm |
These ribbons run the full distance across ACDTop
(actually more, but that's all that will fit) |
| xRibbonTopCent_l |
374 mm |
length of ribbon segments running under the central row
of tiles |
| xRibbonTopMid_l |
337.5 mm |
length of ribbon segments running under rows 1,3
of top tiles |
| xRibbonTopEdge_l |
322.396 mm |
length of ribbon segments running under rows 0,4
of top tiles. Shorten up to avoid bent tile pieces (Jan '06) |
| xRibbonOuter_dxn |
-501.8 mm |
X displacement for X-ribbon #0 |
| xRibbonInner_dxn |
-166 mm |
X displacement for X-ribbon #1 |
| yRibbonOuter_dyn |
-502 mm |
Y displacement for Y-ribbon #0 |
| yRibbonInner_dyn |
-168.4 mm |
Y displacement for Y-ribbon #1 |
| ribbonsSideWidth |
1017.6 mm |
Width of envelope volume to contain 4 side
ribbons |
| ribbonsSideZ |
754.728 mm |
Height of envelope volume to contain 4 side
ribbons. The envelope extends from bottom of
ACDTop volume to back edge of side tiles.
But this isn't quite right! They only go
down to a Z of -15.67 mm, whereas tiles go
down to -45.5. Furthermore, the side parts
of X-ribbons should go higher: nearly up to
underside of the top tiles.
|
| ribbonBentZ |
43.5 mm |
Length (Z) of pieces of ribbon behind extra bent tile pieces
|
| topXRibbonEdge_dz |
761 mm |
Z displacement for outer segments (1 and 5) of top ribbons
running perp. to X axis |
| ribbonBent_dz |
736.75 mm |
Z displacement of extra little pieces of ribbon behind bent tiles
|
| ribbonBentR4_dy |
816.448 mm |
Y displacement for ribbons behind bent tiles in row 4 |
| ribbonBentR0_dy |
-816.448 mm |
Y displacement for ribbons behind bent tiles in row. 0 |
| topXRibbonMid_dz |
748.4 mm |
Z displacement for mid segments (2 and 4) of
top ribbons perp. to x-axis |
| topXRibbonCent_dz |
733.8 mm |
Z displacement for central segment (3) of
top ribbons perp. to x-axis |
| topXRibbonMid_dy |
342.25 mm |
y-displacement of segment 4 |
| topXRibbonMid_dyn |
-342.25 mm |
y-displacement of segment 2 |
| topXRibbonEdge_dy |
658.698 mm |
y-displacement of segment 5 |
| topXRibbonEdge_dyn |
-658.698 mm |
y-displacement of segment 1 |
| ACDSideSupport_dDovetailn |
-13.03 mm |
Negative dovetail distance for those sides
that need it. |
| ACDSideSupport_dtn |
-779.9 mm |
Transverse (x or y) distance of support side from
Ritz origin, negative |
| XTopTileMax |
4 |
Convenience for idField definitons |
| YTopTileMax |
4 |
Convenience for idField definitons |
| ACDShortRowMin |
3 |
row number of first short ACD side row |
| ACDShortRowMax |
3 |
row number of last short ACD side row |
| ACDShortMaxCol |
0 |
Column number of last tile in a short row |
| ACDLongMaxCol |
4 |
Column number of last tile in a long row |
| Name | Value | Description |
| LATX |
1690.94 mm |
X-dimension of an envelope for the LAT,
not including thermal blanket |
| LATY |
1690.94 mm |
Y-dimension of an envelope for the LAT,
not including thermal blanket |
| LATZ |
1064.92 mm |
Z-dimension of an envelope for the LAT,
not including thermal blanket |
| bigXZDim |
4582.4 mm |
Something big enough (for X and Z) to position
everything inside,
with origin where it should be, at the very front
of the grid. |
| biggerZDim |
4582.4 mm |
this is to make room for moving the LAT around in z,
to look for bad hardwired consts. The formula is:
biggerZDim = bigXZDim + 2* abs(globalOffset_dz) |
| NADTotalPanelLen |
6000 mm |
Length of panel proper plus connecting rod |
| bigYDim |
13835.5 mm |
Something big enough to use as Y dimension of
envelope (takes into account solar panels)
|
| solarPanel_dy |
500 mm |
y-displacement of panel-only part of solar panel w.r.t.
envelope including panel and connecting rod |
| solarRod_dy |
-2500 mm |
y-displacement of rod part of solar panel w.r.t.
envelope including panel and connecting rod |
| solarPanelEnv_dy |
3817.78 mm |
y-displacement of entire (+Y) solar panel envelope w.r.t.
Ritz origin. |
| solarPanelEnv_dyn |
-3817.78 mm |
y-displacement of entire (-Y) solar panel envelope w.r.t.
Ritz origin. |
| solarPanelEnv_dz |
-951.2 mm |
z-displacement of entire solar panel envelope w.r.t.
Ritz origin. |
| solarPanelSi_dz |
1 mm |
z-displacement of Si part of solar panel w.r.t.
envelope including panel and connecting rod |
| solarPanelCore_dz |
-2 mm |
z-displacement of core part of solar panel w.r.t.
envelope including panel and connecting rod |
| NADSolarRodDiam |
100 mm |
Diameter of rods connecting solar panels to spacecraft |
| LATZHalf |
532.46 mm |
convenience |
| towersTrans |
1498 mm |
Transverse dimension of envelope containing the towers
|
| innerTowers_dt |
187.25 mm |
Transverse displacement of towers in row (column) 2 |
| outerTowers_dt |
561.75 mm |
Transverse displacement of towers in row (column) 3 |
| innerTowers_dtn |
-187.25 mm |
Transverse displacement of towers in row (column) 1 |
| outerTowers_dtn |
-561.75 mm |
Transverse displacement of towers in row (column) 0 |
| towers_dz |
194.4 mm |
Displacement necessary to get towers origin in the
right place, namely at the front face of the grid
**Decreased by gap between CAL and TKR, nearly the
same as grid flange height, as of 29 Apr 2003**
|
| spacecraft_dz |
-951.2 mm |
Z displacement of spacecraft relative to Ritz origin.
It goes immediately under the LAT |
| tileSide_dz |
379.595 mm |
displacement in z of side tiles rel. to Ritz origin.
Compute relative to ACDTop_d. Find coordinate of top of
ACD side, then subtract half side height.
|
| ribbonsSide_dz |
331.554 mm |
displacement in z of side ribbons rel. to Ritz origin.
Ribbons go down as far as tile sides but don't go up quite as
high. |
| ribbonsSide_dt |
832.47 mm |
Transverse displacement from origin of a side's worth
of ribbons. Place them in an idealized position right
next to side tiles |
| ribbonsSide_dtn |
-832.47 mm |
Transverse displacement from origin of a side's worth
of ribbons on a negative side |
| gridFlangeNoTKR_dz |
112.9 mm |
adjust for placement in smaller envelop |
| gridWebNoTKR_dz |
-5.2 mm |
adjust for placement in smaller envelop |
| CALNoTKR_dz |
-13.45 mm |
adjust for placement in smaller envelop |
| Name | Value | Description |
| NADGridWebWidth |
1516 mm |
Full width of grid web in X or Y |
| NADGridFlangeWidth |
1566 mm |
Full width of grid flange in X or Y |
| NADGridFlangeOuter |
47.95 mm |
Width of outer piece of flange (wider than web) |
| NADGridFlangeInnerHalf |
13.95 mm |
convenience |
| NADGridWebInnerHalf |
4 mm |
convenience |
| NADGridLenLong |
374.5 mm |
Length of longer outer (not per-tower) grid pieces |
| NADGridWebLenShort |
366.5 mm |
Length of shorter outer (not per-tower)
grid web pieces |
| NADGridFlangeLenShort |
346.6 mm |
Length of shorter outer (not per-tower)
grid flange pieces |
| NADGridWebOutsideWidth |
9 mm |
Width of web outside towers (i.e., 4 * towerPitch) |
| NADGridFlangeOutsideWidth |
34 mm |
Width of flange outside towers (i.e., 4 * towerPitch) |
| NADGridWebOutsideLenShort |
1498 mm |
Length of short outside piece of grid web |
| NADGridFlange_dz |
-12.7 mm |
Displacement of flange w.r.t. Ritz origin, which is
at its top face |
| NADGridWeb_dz |
-130.8 mm |
Displacement of grid w.r.t. Ritz origin. Web is
immediately below flange. |
| NADGridFlangeOutsideLenShort |
1498 mm |
Length of short outside piece of grid web |
| NADBlanketTopHoleTrans |
1587.5 mm |
Transverse distance between inner edges of crown
May, 2006. |
| NADBlanketTopInteriorTrans |
1647.94 mm |
Transverse dimension of depressed part of top blanket,
May, 2006 |
| NADBlanketTopMidZ |
1.53 mm |
Z of middle of three stacked volumes comprising blanket
top. |
| NADBlanketSideY_l |
1790.7 mm |
length in long (x) dimension of Y-sides of blanket |
| NADBlanketSideX_l |
1729.1 mm |
length in long (Y) dimension of X-sides of blanket, shorter
than Y-sides because Y-sides cover corners |
| NADBlanketSide_dt |
879.95 mm |
Transverse + displacement of blanket side |
| NADBlanketSide_dtn |
-879.95 mm |
x (resp. y) displacement of neg. x (resp.y)
side of blanket |
| NADBlanketTopInterior_dz |
797 mm |
Z-displacement of blanket interior to crown |
| NADBlanketTopMid_dz |
812.875 mm |
Z-displacement of middle section of blanket, above
interior, below outer crown piece |
| NADBlanketTopTop_dz |
828.75 mm |
Z-displacement of top crown sectio of blanket |
| NADBlanketSides_dz |
354.64 mm |
z displacement of sides of blanket. Sits
just under blanket crown piece. |
| NADBlanketSideToSideTileComp |
19.58 mm |
Compute distance from inner edge of side blanket
to outer edge of side tile (top row) |