2006-04-06 23:18:53,330 seAppBase.py:393 INFO - seAppBase.seStartRun -- Test LatReinit starting run, Operator: NOT-DEFINED, Run Id: 101000064, Time Started: 060406231853 -- Thu Apr 6 23:18:53 2006 2006-04-06 23:18:53,332 seAppBase.py:409 DEBUG - seAppBase.seStartRun -- LatReinit 2006-04-06 23:18:53,337 LatReinit.py:233 DEBUG - LatReinit.startRun() 2006-04-06 23:18:53,342 SequenceStep.py:93 DEBUG - Starting resetSiu1 prerequisite tests 2006-04-06 23:18:53,343 SequenceStep.py:95 DEBUG - Completed resetSiu1 prerequisite tests - result:True 2006-04-06 23:18:53,344 ResetSiu.py:61 DEBUG - Sending SC reset command to SIU 1... 2006-04-06 23:18:56,346 ResetSiu.py:78 DEBUG - Starting resetSiu1 verification tests 2006-04-06 23:18:56,346 ResetSiu.py:179 INFO - Waiting for SIU 1 boot telemetry after SC reset... 2006-04-06 23:19:29,026 SequenceStep.py:585 INFO - SIU boot telemetry received. 2006-04-06 23:19:29,027 PowerSequenceStep.py:309 INFO - Checking for SIU 1 Memory Check PASS... 2006-04-06 23:19:29,992 ScriptEngineConnector.py:792 DEBUG - VscPidsHandler at seconds 0x9e5d981 useconds 0x4a tid 0x9e5d981 pids 0x3 2006-04-06 23:19:30,041 SequenceStep.py:585 INFO - SIU 1 Memory Check passed. 2006-04-06 23:19:30,042 PowerSequenceStep.py:333 INFO - Checking for SIU 1 Comm Check PASS... 2006-04-06 23:19:30,992 ScriptEngineConnector.py:792 DEBUG - VscPidsHandler at seconds 0x9e5d982 useconds 0x49 tid 0x9e5d982 pids 0x3 2006-04-06 23:19:31,006 SequenceStep.py:585 INFO - SIU 1 Comm Check passed. 2006-04-06 23:19:32,009 SequenceStep.py:585 INFO - Diagnostic data confirmed reset of SIU 1 2006-04-06 23:19:42,015 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [605.06813465735604, 605.0681532372414, 605.0681532372414, 605.0681532372414, 605.0681532372414] for SIU 1 is within [600, 700] 2006-04-06 23:19:42,016 ResetSiu.py:106 DEBUG - Completed resetSiu1 verification tests - result:True 2006-04-06 23:19:42,017 SequenceStep.py:93 DEBUG - Starting resetSiu2 prerequisite tests 2006-04-06 23:19:42,018 SequenceStep.py:95 DEBUG - Completed resetSiu2 prerequisite tests - result:True 2006-04-06 23:19:42,019 ResetSiu.py:69 DEBUG - Sending PBC reset command to SIU 1... 2006-04-06 23:19:45,020 ResetSiu.py:78 DEBUG - Starting resetSiu2 verification tests 2006-04-06 23:19:45,021 ResetSiu.py:219 INFO - Waiting for SIU 1 boot telemetry after PBC reset... 2006-04-06 23:19:45,236 SequenceStep.py:585 INFO - SIU boot telemetry received. 2006-04-06 23:19:45,237 PowerSequenceStep.py:309 INFO - Checking for SIU 1 Memory Check PASS... 2006-04-06 23:19:45,992 ScriptEngineConnector.py:792 DEBUG - VscPidsHandler at seconds 0x9e5d991 useconds 0x49 tid 0x9e5d991 pids 0x3 2006-04-06 23:19:46,001 SequenceStep.py:585 INFO - SIU 1 Memory Check passed. 2006-04-06 23:19:46,002 PowerSequenceStep.py:333 INFO - Checking for SIU 1 Comm Check PASS... 2006-04-06 23:19:46,992 ScriptEngineConnector.py:792 DEBUG - VscPidsHandler at seconds 0x9e5d992 useconds 0x49 tid 0x9e5d992 pids 0x3 2006-04-06 23:19:47,018 SequenceStep.py:585 INFO - SIU 1 Comm Check passed. 2006-04-06 23:19:57,025 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [605.06807402825632, 605.0681532372414, 605.0681532372414, 605.0681532372414, 605.0681532372414] for SIU 1 is within [600, 700] 2006-04-06 23:19:57,025 ResetSiu.py:106 DEBUG - Completed resetSiu2 verification tests - result:True 2006-04-06 23:19:57,027 ReinitSecondarySiuBoot.py:54 DEBUG - Starting secondarySiuBoot1 prerequisite tests 2006-04-06 23:19:57,028 PowerSequenceStep.py:60 INFO - Waiting for SIU 1 boot telemetry... 2006-04-06 23:19:57,242 SequenceStep.py:585 INFO - SIU boot telemetry received. 2006-04-06 23:19:57,243 ReinitSecondarySiuBoot.py:63 DEBUG - Completed secondarySiuBoot1 prerequisite tests - result:True 2006-04-06 23:19:57,244 SequenceStep.py:585 INFO - Sending secondary boot command to SIU 1 using flags hi=0x5400, lo=0xc000 ... 2006-04-06 23:19:57,246 ReinitSecondarySiuBoot.py:86 DEBUG - Starting secondarySiuBoot1 verification tests 2006-04-06 23:19:57,246 SequenceStep.py:567 INFO - Waiting for operator acknowledgement: Load VxWorks libraries for SIU 1 and click OK to continue 2006-04-06 23:23:09,018 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:09,018 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:23:09,019 LIM.py:260 DEBUG - Action : 1 2006-04-06 23:23:09,021 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:23:09,021 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:09,022 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:09,024 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:09,024 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:23:09,025 LIM.py:260 DEBUG - Action : 53 2006-04-06 23:23:09,027 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:23:09,027 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:09,028 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:15,152 SequenceStep.py:573 INFO - Operator confirmed the successful completion of manual task 2006-04-06 23:23:15,155 ReinitSecondarySiuBoot.py:124 INFO - Waiting for LAT housekeeping telemetry... 2006-04-06 23:23:15,230 SequenceStep.py:585 INFO - LAT housekeeping telemetry received. 2006-04-06 23:23:20,469 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [10.06962703775373, 10.074852874985629, 10.079690490402209, 9.9835601192860768, 9.9885776662241152] for SIU 1 is within [9, 11] 2006-04-06 23:23:20,474 ReinitSecondarySiuBoot.py:112 DEBUG - Completed secondarySiuBoot1 verification tests - result:True 2006-04-06 23:23:20,475 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:23:21,439 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:23:21,444 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnPdu1.st.f with file ID 0x23400001=591396865 2006-04-06 23:23:24,308 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000001 2006-04-06 23:23:25,622 SequenceStep.py:447 INFO - Uploaded file LhkPowerOnPdu1.st.f with file id 0x23400001 2006-04-06 23:23:25,626 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400001 2006-04-06 23:23:26,448 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400001 2006-04-06 23:23:26,457 PowerOnPdu.py:79 DEBUG - Starting powerOnPdu1 prerequisite tests 2006-04-06 23:23:26,461 PowerSequenceStep.py:354 INFO - Checking if the DAQ feed voltage is within range [27.0, 29.0]... 2006-04-06 23:23:27,026 SequenceStep.py:585 INFO - DAQ feed voltage 28.08V is within [27.0, 29.0] 2006-04-06 23:23:27,027 PowerSequenceStep.py:390 INFO - Checking if PDU temperature is within range [-30.0, 45.0]... 2006-04-06 23:23:28,043 SequenceStep.py:585 INFO - PDU temperature 21.69C is within [-30.0, 45.0] 2006-04-06 23:23:28,044 PowerSequenceStep.py:477 INFO - Checking if the GASU temperature is within range [-30.0, 45.0]... 2006-04-06 23:23:29,010 SequenceStep.py:585 INFO - GASU temperature 22.93C is within [-30.0, 45.0] 2006-04-06 23:23:29,011 PowerOnPdu.py:94 DEBUG - Completed powerOnPdu1 prerequisite tests - result:True 2006-04-06 23:23:29,012 PowerOnPdu.py:99 INFO - Sending main feed on for SIU 1 PDU 1 2006-04-06 23:23:31,219 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:31,219 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:23:31,220 LIM.py:260 DEBUG - Action : 3 2006-04-06 23:23:31,226 LIM.py:261 DEBUG - Status : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"') 2006-04-06 23:23:31,226 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:31,227 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:31,230 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:31,231 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:23:31,231 LIM.py:260 DEBUG - Action : 7 2006-04-06 23:23:31,237 LIM.py:261 DEBUG - Status : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"') 2006-04-06 23:23:31,238 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:31,238 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:31,242 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:31,242 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:23:31,242 LIM.py:260 DEBUG - Action : 6 2006-04-06 23:23:31,244 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:23:31,245 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:31,245 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:31,249 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:31,250 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:23:31,250 LIM.py:260 DEBUG - Action : 74 2006-04-06 23:23:31,252 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:23:31,253 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:31,253 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:31,257 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:31,257 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:23:31,258 LIM.py:260 DEBUG - Action : 75 2006-04-06 23:23:31,260 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:23:31,260 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:31,261 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:31,264 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:23:31,265 LIM.py:259 DEBUG - Operating Mode: 1 2006-04-06 23:23:31,265 LIM.py:260 DEBUG - Action : 2 2006-04-06 23:23:31,267 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:23:31,268 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:23:31,268 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:23:31,279 PowerOnPdu.py:142 INFO - Verified main feed on action. 2006-04-06 23:23:31,283 PowerOnPdu.py:151 INFO - Verified operating mode change to QUIESCENT. 2006-04-06 23:23:31,288 PowerOnPdu.py:159 INFO - Completed main feed on action, result:True 2006-04-06 23:23:31,289 PowerOnPdu.py:207 DEBUG - Starting powerOnPdu1 verification tests 2006-04-06 23:23:31,289 PowerSequenceStep.py:354 INFO - Checking if the DAQ feed voltage is within range [27.0, 29.0]... 2006-04-06 23:23:32,010 SequenceStep.py:585 INFO - DAQ feed voltage 28.03V is within [27.0, 29.0] 2006-04-06 23:23:32,011 PowerSequenceStep.py:390 INFO - Checking if PDU temperature is within range [-30.0, 45.0]... 2006-04-06 23:23:33,026 SequenceStep.py:585 INFO - PDU temperature 21.63C is within [-30.0, 45.0] 2006-04-06 23:23:33,027 PowerSequenceStep.py:433 INFO - Checking if the PDU 1 3.3V voltage is within range [3.0, 3.6000000000000001]... 2006-04-06 23:23:34,043 SequenceStep.py:585 INFO - PDU 1 3.3Vvoltage 3.35V is within [3.0, 3.6000000000000001] 2006-04-06 23:23:34,043 PowerSequenceStep.py:477 INFO - Checking if the GASU temperature is within range [-30.0, 45.0]... 2006-04-06 23:23:35,011 SequenceStep.py:585 INFO - GASU temperature 23.74C is within [-30.0, 45.0] 2006-04-06 23:23:35,012 PowerSequenceStep.py:781 INFO - Checking if the AEM/EBM 3.3V and AEM/EBM 2.5V voltages are within range [[3.0, 3.6000000000000001], [2.0, 2.6000000000000001]]... 2006-04-06 23:23:36,027 SequenceStep.py:585 INFO - AEM/EBM 3.3V voltage 3.28V is within [3.0, 3.6000000000000001] 2006-04-06 23:23:36,028 SequenceStep.py:585 INFO - AEM/EBM 2.5V voltage 2.48V is within [2.0, 2.6000000000000001] 2006-04-06 23:23:36,028 PowerSequenceStep.py:830 INFO - Checking if the CRU/GEM 3.3V and CRU/GEM 2.5V voltages are within range [[3.0, 3.6000000000000001], [2.0, 2.6000000000000001]]... 2006-04-06 23:23:36,994 SequenceStep.py:585 INFO - CRU/GEM 3.3V voltage 3.32V is within [3.0, 3.6000000000000001] 2006-04-06 23:23:36,995 SequenceStep.py:585 INFO - CRU/GEM 2.5V voltage 2.44V is within [2.0, 2.6000000000000001] 2006-04-06 23:23:36,996 PowerSequenceStep.py:195 INFO - Reading the DAQ feed current... 2006-04-06 23:23:38,011 SequenceStep.py:585 INFO - Read the DAQ feed current as 2.73A 2006-04-06 23:23:38,012 PowerOnPdu.py:240 DEBUG - Completed powerOnPdu1 verification tests - result:True 2006-04-06 23:23:38,012 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:23:39,427 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:23:39,436 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnEpu0.st.f with file ID 0x23400002=591396866 2006-04-06 23:23:42,297 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000002 2006-04-06 23:23:43,662 SequenceStep.py:447 INFO - Uploaded file LhkPowerOnEpu0.st.f with file id 0x23400002 2006-04-06 23:23:43,666 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002 2006-04-06 23:23:44,438 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400002 2006-04-06 23:23:44,443 SequenceStep.py:93 DEBUG - Starting resetEpu prerequisite tests 2006-04-06 23:23:44,448 SequenceStep.py:95 DEBUG - Completed resetEpu prerequisite tests - result:True 2006-04-06 23:23:44,452 ResetEpu.py:67 DEBUG - Sending warm boot command to EPU 0... 2006-04-06 23:23:44,454 ResetEpu.py:75 DEBUG - Starting resetEpu verification tests 2006-04-06 23:23:44,454 ResetEpu.py:151 INFO - Waiting for EPU 0 boot telemetry... 2006-04-06 23:23:47,622 SequenceStep.py:585 INFO - EPU 0 boot telemetry received. 2006-04-06 23:23:48,624 SequenceStep.py:585 INFO - Diagnostic data confirmed warm reboot of EPU 0 2006-04-06 23:23:53,631 SequenceStep.py:585 INFO - Watchdog timer is enabled: The timer values [605.06854537061145, 605.06855906105329, 605.068560038942, 605.068560038942, 605.068560038942] for EPU 0 is within [600, 700] 2006-04-06 23:23:53,632 ResetEpu.py:91 DEBUG - Completed resetEpu verification tests - result:True 2006-04-06 23:23:53,633 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:23:54,448 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:23:54,453 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnEpu1.st.f with file ID 0x23400003=591396867 2006-04-06 23:23:57,318 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000003 2006-04-06 23:23:58,632 SequenceStep.py:447 INFO - Uploaded file LhkPowerOnEpu1.st.f with file id 0x23400003 2006-04-06 23:23:58,636 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400003 2006-04-06 23:23:59,458 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400003 2006-04-06 23:23:59,467 SequenceStep.py:93 DEBUG - Starting resetEpu prerequisite tests 2006-04-06 23:23:59,471 SequenceStep.py:95 DEBUG - Completed resetEpu prerequisite tests - result:True 2006-04-06 23:23:59,472 ResetEpu.py:67 DEBUG - Sending warm boot command to EPU 1... 2006-04-06 23:23:59,474 ResetEpu.py:75 DEBUG - Starting resetEpu verification tests 2006-04-06 23:23:59,474 ResetEpu.py:151 INFO - Waiting for EPU 1 boot telemetry... 2006-04-06 23:24:02,639 SequenceStep.py:585 INFO - EPU 1 boot telemetry received. 2006-04-06 23:24:03,641 SequenceStep.py:585 INFO - Diagnostic data confirmed warm reboot of EPU 1 2006-04-06 23:24:08,649 SequenceStep.py:585 INFO - Watchdog timer is enabled: The timer values [605.06854537061145, 605.06855906105329, 605.068560038942, 605.06855906105329, 605.068560038942] for EPU 1 is within [600, 700] 2006-04-06 23:24:08,650 ResetEpu.py:91 DEBUG - Completed resetEpu verification tests - result:True 2006-04-06 23:24:08,650 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:24:09,464 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:24:09,469 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400002 2006-04-06 23:24:10,440 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400002 2006-04-06 23:24:10,445 ReinitSecondaryEpuBoot.py:63 DEBUG - Starting secondaryEpuBoot1 prerequisite tests 2006-04-06 23:24:10,450 ReinitSecondaryEpuBoot.py:164 INFO - Waiting for EPU 0 boot telemetry... 2006-04-06 23:24:10,668 SequenceStep.py:585 INFO - EPU 0 boot telemetry received. 2006-04-06 23:24:10,669 ReinitSecondaryEpuBoot.py:71 DEBUG - Completed secondaryEpuBoot1 prerequisite tests - result:True 2006-04-06 23:24:10,669 SequenceStep.py:585 INFO - Sending secondary boot command to EPU 0 using flags hi=0x5400, lo=0xc000 ... 2006-04-06 23:24:10,672 ReinitSecondaryEpuBoot.py:92 DEBUG - Starting secondaryEpuBoot1 verification tests 2006-04-06 23:24:10,672 SequenceStep.py:567 INFO - Waiting for operator acknowledgement: Load VxWorks libraries for EPU 0 and click OK to continue 2006-04-06 23:28:36,223 SequenceStep.py:573 INFO - Operator confirmed the successful completion of manual task 2006-04-06 23:28:36,223 PowerSequenceStep.py:623 INFO - Checking if EPU 0 CPU junction temperature is within range [1, 999]...... 2006-04-06 23:28:38,420 SequenceStep.py:585 INFO - EPU 0 CPU junction temperature measured as 47 and within the required range of [1, 999] 2006-04-06 23:28:43,461 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [9.9851599452051243, 9.9884182703654325, 9.9927708529850392, 9.9959978857068332, 9.999831209424844] for EPU 0 is within [9, 11] 2006-04-06 23:28:43,466 ReinitSecondaryEpuBoot.py:120 DEBUG - Completed secondaryEpuBoot1 verification tests - result:True 2006-04-06 23:28:43,466 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:28:44,430 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:28:44,438 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400003 2006-04-06 23:28:45,456 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400003 2006-04-06 23:28:45,461 ReinitSecondaryEpuBoot.py:63 DEBUG - Starting secondaryEpuBoot1 prerequisite tests 2006-04-06 23:28:45,465 ReinitSecondaryEpuBoot.py:164 INFO - Waiting for EPU 1 boot telemetry... 2006-04-06 23:28:45,633 SequenceStep.py:585 INFO - EPU 1 boot telemetry received. 2006-04-06 23:28:45,634 ReinitSecondaryEpuBoot.py:71 DEBUG - Completed secondaryEpuBoot1 prerequisite tests - result:True 2006-04-06 23:28:45,635 SequenceStep.py:585 INFO - Sending secondary boot command to EPU 1 using flags hi=0x5400, lo=0xc000 ... 2006-04-06 23:28:45,637 ReinitSecondaryEpuBoot.py:92 DEBUG - Starting secondaryEpuBoot1 verification tests 2006-04-06 23:28:45,637 SequenceStep.py:567 INFO - Waiting for operator acknowledgement: Load VxWorks libraries for EPU 1 and click OK to continue 2006-04-06 23:29:49,220 SequenceStep.py:573 INFO - Operator confirmed the successful completion of manual task 2006-04-06 23:29:49,220 PowerSequenceStep.py:623 INFO - Checking if EPU 1 CPU junction temperature is within range [1, 999]...... 2006-04-06 23:29:51,421 SequenceStep.py:585 INFO - EPU 1 CPU junction temperature measured as 43 and within the required range of [1, 999] 2006-04-06 23:29:56,456 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [10.004395016004423, 10.007404957434025, 10.010652525818593, 10.013541209048951, 10.016781932212595] for EPU 1 is within [9, 11] 2006-04-06 23:29:56,461 ReinitSecondaryEpuBoot.py:120 DEBUG - Completed secondaryEpuBoot1 verification tests - result:True 2006-04-06 23:29:56,462 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:29:57,425 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:29:57,430 SequenceStep.py:93 DEBUG - Starting induceSiuWatchdogTimeout prerequisite tests 2006-04-06 23:29:57,435 SequenceStep.py:95 DEBUG - Completed induceSiuWatchdogTimeout prerequisite tests - result:True 2006-04-06 23:29:57,439 InduceSiuWatchdogTimeout.py:56 DEBUG - Inducing SIU 1 watchdog timeout... 2006-04-06 23:29:57,441 testAppBase.py:681 INFO - Wrote 1 words to memory location 0xbf880058 on unit SIU, status=1 2006-04-06 23:29:57,442 InduceSiuWatchdogTimeout.py:72 DEBUG - Starting induceSiuWatchdogTimeout verification tests 2006-04-06 23:29:57,442 InduceSiuWatchdogTimeout.py:95 INFO - Waiting for SIU 1 boot telemetry after watchdog timeout... 2006-04-06 23:30:19,664 SequenceStep.py:585 INFO - SIU 1 boot telemetry received. 2006-04-06 23:30:19,665 InduceSiuWatchdogTimeout.py:81 DEBUG - Completed induceSiuWatchdogTimeout verification tests - result:True 2006-04-06 23:30:19,666 ReinitSecondarySiuBoot.py:54 DEBUG - Starting secondarySiuBoot2 prerequisite tests 2006-04-06 23:30:19,667 PowerSequenceStep.py:60 INFO - Waiting for SIU 1 boot telemetry... 2006-04-06 23:30:20,032 SequenceStep.py:585 INFO - SIU boot telemetry received. 2006-04-06 23:30:20,033 ReinitSecondarySiuBoot.py:63 DEBUG - Completed secondarySiuBoot2 prerequisite tests - result:True 2006-04-06 23:30:20,034 SequenceStep.py:585 INFO - Sending secondary boot command to SIU 1 using flags hi=0x5400, lo=0xc000 ... 2006-04-06 23:30:20,035 ReinitSecondarySiuBoot.py:86 DEBUG - Starting secondarySiuBoot2 verification tests 2006-04-06 23:30:20,036 SequenceStep.py:567 INFO - Waiting for operator acknowledgement: Load VxWorks libraries for SIU 1 and click OK to continue 2006-04-06 23:31:37,421 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:37,422 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:31:37,422 LIM.py:260 DEBUG - Action : 1 2006-04-06 23:31:37,425 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:31:37,425 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:37,425 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:37,428 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:37,428 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:31:37,428 LIM.py:260 DEBUG - Action : 53 2006-04-06 23:31:37,431 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:31:37,431 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:37,432 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:40,996 SequenceStep.py:573 INFO - Operator confirmed the successful completion of manual task 2006-04-06 23:31:40,998 ReinitSecondarySiuBoot.py:124 INFO - Waiting for LAT housekeeping telemetry... 2006-04-06 23:31:41,040 SequenceStep.py:585 INFO - LAT housekeeping telemetry received. 2006-04-06 23:31:46,426 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [10.053014664457416, 10.057740800561788, 10.06287960569907, 10.068317644779645, 10.073441781586371] for SIU 1 is within [9, 11] 2006-04-06 23:31:46,430 ReinitSecondarySiuBoot.py:112 DEBUG - Completed secondarySiuBoot2 verification tests - result:True 2006-04-06 23:31:46,431 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:31:47,445 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:31:47,451 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnPdu1.st.f with file ID 0x23400004=591396868 2006-04-06 23:31:50,316 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000004 2006-04-06 23:31:51,642 SequenceStep.py:447 INFO - Uploaded file LhkPowerOnPdu1.st.f with file id 0x23400004 2006-04-06 23:31:51,647 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400004 2006-04-06 23:31:52,418 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400004 2006-04-06 23:31:52,426 PowerOnPdu.py:79 DEBUG - Starting powerOnPdu2 prerequisite tests 2006-04-06 23:31:52,431 PowerSequenceStep.py:354 INFO - Checking if the DAQ feed voltage is within range [27.0, 29.0]... 2006-04-06 23:31:52,995 SequenceStep.py:585 INFO - DAQ feed voltage 27.93V is within [27.0, 29.0] 2006-04-06 23:31:52,996 PowerSequenceStep.py:390 INFO - Checking if PDU temperature is within range [-30.0, 45.0]... 2006-04-06 23:31:54,011 SequenceStep.py:585 INFO - PDU temperature 22.34C is within [-30.0, 45.0] 2006-04-06 23:31:54,012 PowerSequenceStep.py:477 INFO - Checking if the GASU temperature is within range [-30.0, 45.0]... 2006-04-06 23:31:55,027 SequenceStep.py:585 INFO - GASU temperature 23.20C is within [-30.0, 45.0] 2006-04-06 23:31:55,028 PowerOnPdu.py:94 DEBUG - Completed powerOnPdu2 prerequisite tests - result:True 2006-04-06 23:31:55,029 PowerOnPdu.py:99 INFO - Sending main feed on for SIU 1 PDU 1 2006-04-06 23:31:57,219 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:57,219 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:31:57,220 LIM.py:260 DEBUG - Action : 3 2006-04-06 23:31:57,226 LIM.py:261 DEBUG - Status : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"') 2006-04-06 23:31:57,226 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:57,227 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:57,230 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:57,231 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:31:57,231 LIM.py:260 DEBUG - Action : 7 2006-04-06 23:31:57,237 LIM.py:261 DEBUG - Status : 0x210077f8 - ('PIG_INMUD', '"Happy as a pig in mud"') 2006-04-06 23:31:57,238 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:57,238 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:57,242 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:57,242 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:31:57,243 LIM.py:260 DEBUG - Action : 6 2006-04-06 23:31:57,245 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:31:57,245 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:57,246 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:57,249 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:57,250 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:31:57,250 LIM.py:260 DEBUG - Action : 74 2006-04-06 23:31:57,252 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:31:57,253 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:57,253 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:57,257 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:57,257 LIM.py:259 DEBUG - Operating Mode: 0 2006-04-06 23:31:57,258 LIM.py:260 DEBUG - Action : 75 2006-04-06 23:31:57,260 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:31:57,260 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:57,261 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:57,264 LIM.py:258 DEBUG - LIM State: 2006-04-06 23:31:57,265 LIM.py:259 DEBUG - Operating Mode: 1 2006-04-06 23:31:57,265 LIM.py:260 DEBUG - Action : 2 2006-04-06 23:31:57,267 LIM.py:261 DEBUG - Status : 0x598333a8 - ('LIM_SUCCESS', '"Success"') 2006-04-06 23:31:57,268 LIM.py:263 DEBUG - SaaTransit : 0 2006-04-06 23:31:57,269 LIM.py:264 DEBUG - HV Allow : 0 2006-04-06 23:31:57,297 PowerOnPdu.py:142 INFO - Verified main feed on action. 2006-04-06 23:31:57,297 PowerOnPdu.py:151 INFO - Verified operating mode change to QUIESCENT. 2006-04-06 23:31:57,298 PowerOnPdu.py:159 INFO - Completed main feed on action, result:True 2006-04-06 23:31:57,299 PowerOnPdu.py:207 DEBUG - Starting powerOnPdu2 verification tests 2006-04-06 23:31:57,299 PowerSequenceStep.py:354 INFO - Checking if the DAQ feed voltage is within range [27.0, 29.0]... 2006-04-06 23:31:58,015 SequenceStep.py:585 INFO - DAQ feed voltage 27.93V is within [27.0, 29.0] 2006-04-06 23:31:58,016 PowerSequenceStep.py:390 INFO - Checking if PDU temperature is within range [-30.0, 45.0]... 2006-04-06 23:31:59,032 SequenceStep.py:585 INFO - PDU temperature 22.02C is within [-30.0, 45.0] 2006-04-06 23:31:59,033 PowerSequenceStep.py:433 INFO - Checking if the PDU 1 3.3V voltage is within range [3.0, 3.6000000000000001]... 2006-04-06 23:31:59,998 SequenceStep.py:585 INFO - PDU 1 3.3Vvoltage 3.37V is within [3.0, 3.6000000000000001] 2006-04-06 23:31:59,999 PowerSequenceStep.py:477 INFO - Checking if the GASU temperature is within range [-30.0, 45.0]... 2006-04-06 23:32:01,014 SequenceStep.py:585 INFO - GASU temperature 22.93C is within [-30.0, 45.0] 2006-04-06 23:32:01,015 PowerSequenceStep.py:781 INFO - Checking if the AEM/EBM 3.3V and AEM/EBM 2.5V voltages are within range [[3.0, 3.6000000000000001], [2.0, 2.6000000000000001]]... 2006-04-06 23:32:02,035 SequenceStep.py:585 INFO - AEM/EBM 3.3V voltage 3.32V is within [3.0, 3.6000000000000001] 2006-04-06 23:32:02,036 SequenceStep.py:585 INFO - AEM/EBM 2.5V voltage 2.46V is within [2.0, 2.6000000000000001] 2006-04-06 23:32:02,037 PowerSequenceStep.py:830 INFO - Checking if the CRU/GEM 3.3V and CRU/GEM 2.5V voltages are within range [[3.0, 3.6000000000000001], [2.0, 2.6000000000000001]]... 2006-04-06 23:32:03,001 SequenceStep.py:585 INFO - CRU/GEM 3.3V voltage 3.35V is within [3.0, 3.6000000000000001] 2006-04-06 23:32:03,002 SequenceStep.py:585 INFO - CRU/GEM 2.5V voltage 2.46V is within [2.0, 2.6000000000000001] 2006-04-06 23:32:03,003 PowerSequenceStep.py:195 INFO - Reading the DAQ feed current... 2006-04-06 23:32:04,017 SequenceStep.py:585 INFO - Read the DAQ feed current as 2.29A 2006-04-06 23:32:04,018 PowerOnPdu.py:240 DEBUG - Completed powerOnPdu2 verification tests - result:True 2006-04-06 23:32:04,019 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:32:05,432 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:32:05,437 SequenceStep.py:93 DEBUG - Starting induceEpuWatchdogTimeout prerequisite tests 2006-04-06 23:32:05,442 SequenceStep.py:95 DEBUG - Completed induceEpuWatchdogTimeout prerequisite tests - result:True 2006-04-06 23:32:05,446 InduceEpuWatchdogTimeout.py:63 DEBUG - Inducing EPU 0 watchdog timeout... 2006-04-06 23:32:05,448 testAppBase.py:681 INFO - Wrote 1 words to memory location 0xbf880058 on unit EPU0, status=1 2006-04-06 23:32:05,449 InduceEpuWatchdogTimeout.py:79 DEBUG - Starting induceEpuWatchdogTimeout verification tests 2006-04-06 23:32:05,449 InduceEpuWatchdogTimeout.py:103 INFO - Waiting for EPU 0 boot telemetry after watchdog timeout... 2006-04-06 23:32:27,468 SequenceStep.py:585 INFO - EPU 0 boot telemetry received. 2006-04-06 23:32:27,468 InduceEpuWatchdogTimeout.py:88 DEBUG - Completed induceEpuWatchdogTimeout verification tests - result:True 2006-04-06 23:32:27,469 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:32:28,434 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:32:28,438 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnEpu0.st.f with file ID 0x23400005=591396869 2006-04-06 23:32:31,300 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000005 2006-04-06 23:32:32,664 SequenceStep.py:447 INFO - Uploaded file LhkPowerOnEpu0.st.f with file id 0x23400005 2006-04-06 23:32:32,669 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400005 2006-04-06 23:32:33,440 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400005 2006-04-06 23:32:33,445 ReinitSecondaryEpuBoot.py:63 DEBUG - Starting secondaryEpuBoot2 prerequisite tests 2006-04-06 23:32:33,453 ReinitSecondaryEpuBoot.py:164 INFO - Waiting for EPU 0 boot telemetry... 2006-04-06 23:32:33,671 SequenceStep.py:585 INFO - EPU 0 boot telemetry received. 2006-04-06 23:32:33,672 ReinitSecondaryEpuBoot.py:71 DEBUG - Completed secondaryEpuBoot2 prerequisite tests - result:True 2006-04-06 23:32:33,673 SequenceStep.py:585 INFO - Sending secondary boot command to EPU 0 using flags hi=0x5400, lo=0xc000 ... 2006-04-06 23:32:33,674 ReinitSecondaryEpuBoot.py:92 DEBUG - Starting secondaryEpuBoot2 verification tests 2006-04-06 23:32:33,675 SequenceStep.py:567 INFO - Waiting for operator acknowledgement: Load VxWorks libraries for EPU 0 and click OK to continue 2006-04-06 23:35:47,989 SequenceStep.py:573 INFO - Operator confirmed the successful completion of manual task 2006-04-06 23:35:47,990 PowerSequenceStep.py:623 INFO - Checking if EPU 0 CPU junction temperature is within range [1, 999]...... 2006-04-06 23:35:50,442 SequenceStep.py:585 INFO - EPU 0 CPU junction temperature measured as 47 and within the required range of [1, 999] 2006-04-06 23:35:55,425 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [10.015269138388165, 10.018276146151655, 10.021795567595818, 10.024805509025418, 10.028032541747212] for EPU 0 is within [9, 11] 2006-04-06 23:35:55,430 ReinitSecondaryEpuBoot.py:120 DEBUG - Completed secondaryEpuBoot2 verification tests - result:True 2006-04-06 23:35:55,430 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:35:56,447 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:35:56,450 SequenceStep.py:93 DEBUG - Starting induceEpuWatchdogTimeout prerequisite tests 2006-04-06 23:35:56,457 SequenceStep.py:95 DEBUG - Completed induceEpuWatchdogTimeout prerequisite tests - result:True 2006-04-06 23:35:56,461 InduceEpuWatchdogTimeout.py:63 DEBUG - Inducing EPU 1 watchdog timeout... 2006-04-06 23:35:56,464 testAppBase.py:681 INFO - Wrote 1 words to memory location 0xbf880058 on unit EPU1, status=1 2006-04-06 23:35:56,464 InduceEpuWatchdogTimeout.py:79 DEBUG - Starting induceEpuWatchdogTimeout verification tests 2006-04-06 23:35:56,465 InduceEpuWatchdogTimeout.py:103 INFO - Waiting for EPU 1 boot telemetry after watchdog timeout... 2006-04-06 23:36:18,439 SequenceStep.py:585 INFO - EPU 1 boot telemetry received. 2006-04-06 23:36:18,440 InduceEpuWatchdogTimeout.py:88 DEBUG - Completed induceEpuWatchdogTimeout verification tests - result:True 2006-04-06 23:36:18,441 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:36:19,455 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:36:19,460 LHK.py:86 DEBUG - Uploading file /usr/local/online/LICOS_Config/lhk/LhkPowerOnEpu1.st.f with file ID 0x23400006=591396870 2006-04-06 23:36:22,325 FILE.py:472 DEBUG - committing to unit:0, flags:0, id:/ram/d013/f0000006 2006-04-06 23:36:23,641 SequenceStep.py:447 INFO - Uploaded file LhkPowerOnEpu1.st.f with file id 0x23400006 2006-04-06 23:36:23,646 SequenceStep.py:449 DEBUG - Configuring LHK with file id 0x23400006 2006-04-06 23:36:24,465 SequenceStep.py:454 INFO - Configured LHK with file id 0x23400006 2006-04-06 23:36:24,470 ReinitSecondaryEpuBoot.py:63 DEBUG - Starting secondaryEpuBoot2 prerequisite tests 2006-04-06 23:36:24,478 ReinitSecondaryEpuBoot.py:164 INFO - Waiting for EPU 1 boot telemetry... 2006-04-06 23:36:24,644 SequenceStep.py:585 INFO - EPU 1 boot telemetry received. 2006-04-06 23:36:24,644 ReinitSecondaryEpuBoot.py:71 DEBUG - Completed secondaryEpuBoot2 prerequisite tests - result:True 2006-04-06 23:36:24,645 SequenceStep.py:585 INFO - Sending secondary boot command to EPU 1 using flags hi=0x5400, lo=0xc000 ... 2006-04-06 23:36:24,647 ReinitSecondaryEpuBoot.py:92 DEBUG - Starting secondaryEpuBoot2 verification tests 2006-04-06 23:36:24,647 SequenceStep.py:567 INFO - Waiting for operator acknowledgement: Load VxWorks libraries for EPU 1 and click OK to continue 2006-04-06 23:37:53,581 SequenceStep.py:573 INFO - Operator confirmed the successful completion of manual task 2006-04-06 23:37:53,582 PowerSequenceStep.py:623 INFO - Checking if EPU 1 CPU junction temperature is within range [1, 999]...... 2006-04-06 23:37:55,430 SequenceStep.py:585 INFO - EPU 1 CPU junction temperature measured as 43 and within the required range of [1, 999] 2006-04-06 23:38:00,465 SequenceStep.py:585 INFO - Watchdog function is enabled: The timer values [10.064224202666484, 10.067569559921409, 10.071081158255945, 10.074503768718452, 10.07766039345359] for EPU 1 is within [9, 11] 2006-04-06 23:38:00,470 ReinitSecondaryEpuBoot.py:120 DEBUG - Completed secondaryEpuBoot2 verification tests - result:True 2006-04-06 23:38:00,470 SequenceStep.py:462 DEBUG - Configuring LHK with the default configuration 2006-04-06 23:38:01,436 SequenceStep.py:467 INFO - Configured LHK with the default configuration 2006-04-06 23:38:01,441 seAppBase.py:427 DEBUG - seAppBase.seStopRun -- LatReinit 2006-04-06 23:38:01,491 seAppBase.py:951 DEBUG - Generating run report... 2006-04-06 23:38:01,494 rcReportGen.py:95 DEBUG - Database elogbook opened successfully 2006-04-06 23:38:01,842 seAppBase.py:1080 DEBUG - Run report generation complete. 2006-04-06 23:38:01,842 seAppBase.py:1201 INFO - seAppBase.seStopRun -- Test LatReinit finished, Run Id: 101000064, Status: PASSED, Completion Time: Thu Apr 6 23:38:01 2006